BRITEQ BT-FOG3300 (01) PDF Document

The BRITEQ BT-FOG3300 can be controlled manually or with a timer using the display and buttons, by using the included RF remote, via full DMX control with RDM support, or by using a wireless DMX USB-dongle connected to the dedicated USB-port.

To produce fog manually, simply press the FOG button on the unit. To stop the fog output, press the ENTER/STOP button.

First, ensure the display shows READY TO WORK. Then, press the UP & TIMER button to activate the timer. The device will then execute the fog output volume, duration, and interval settings configured in the menu.

Switch off the BRITEQ BT-FOG3300 and wait for it to cool down. Remove the nozzle and empty the fluid from the tank. Fill the tank with a solution of 80% distilled water and 20% white vinegar. Switch on the unit and wait for the warm-up time. Operate the device in continuous mode until the tank is empty. Reinstall the nozzle, then remove any cleaning solution residue and refill the tank with fresh fog fluid.

Press the MENU button repeatedly until DMX512 ADDRESS appears on the display. Use the DOWN and UP buttons to select the desired address, then press the ENTER button to confirm.

Press the MENU button until DMX MODE is shown on the display. Use the DOWN and UP buttons to toggle between 1 CH or 2 CH, then press the ENTER button to confirm.

Press the MENU button until FOG OUTPUT is displayed. Use the DOWN and UP buttons to set the desired volume percentage. Press the ENTER button to confirm the setting.

Press the MENU button until INTERVAL SET appears. Use the DOWN and UP buttons to select an interval between 1 second and 600 seconds. Press the ENTER button to confirm your selection.

Press the MENU button until DURATION SET appears on the display. Use the DOWN and UP buttons to choose a duration between 2 seconds and 255 seconds. Press the ENTER button to confirm.

Press the MENU button until FLUID SENSOR is displayed. Use the DOWN and UP buttons to toggle between ON and OFF, then press the ENTER button to confirm.

Press the MENU button until WIRELESS CONTROL is shown on the display. Use the DOWN and UP buttons to select ON, then press the ENTER button to confirm. Note that this feature is automatically disabled if a DMX signal is connected.

Yes. Press the MENU button until KEY TONE appears. Use the DOWN and UP buttons to select HIGH, MEDIUM, LOW, or OFF, then press the ENTER button to save the setting.

Ensure the installation area can hold 10 times the device’s weight. Use a certified safety cable capable of holding 12 times the weight of the device. The safety attachment must ensure that the unit cannot drop more than 20cm. Always perform rigging during times when no persons are below the unit.

First, identify and resolve the underlying issue that caused the breaker to trip. Once the issue is addressed, push the breaker button on the unit to reset it.

Connect your DMX controller to the DMX INPUT (3-pin or 5-pin) on the BRITEQ BT-FOG3300. If you have additional units, connect them to the DMX OUTPUT. Always use a 90 to 120 ohm terminator at the end of the chain to prevent interference.

In 1 channel DMX mode, channel 1 controls the fog output volume using values 000-255.

Channel 1 controls the fog output volume (000-255). Channel 2 controls the mode: 000-005 for normal working mode, and 006-255 for continuous fog mode.

The BRITEQ BT-FOG3300 operates at 3300 Watts and produces an output of 60,000 cubic feet per minute (1,699 cubic meters per minute).

The BRITEQ BT-FOG3300 is equipped with a 6-liter fluid reservoir.

The warm-up time for the BRITEQ BT-FOG3300 is approximately 6 minutes.

The BRITEQ BT-FOG3300 measures 50cm by 42cm by 27cm and weighs 16.29 kilograms.

Yes, the BRITEQ BT-FOG3300 features a MAINS OUTPUT CONNECTOR that can be used to send power to other devices, with a maximum capacity of 1500 Watts.

You must keep a minimum distance of at least 1 meter from the BRITEQ BT-FOG3300 fog output nozzle because the fog is very hot and can cause serious burns.

The BRITEQ BT-FOG3300 is for indoor use only. It should be located in a well-ventilated spot away from flammable materials and liquids. The maximum safe ambient temperature is 40 degrees Celsius.

To prevent fire or shock hazards, do not expose the BRITEQ BT-FOG3300 to rain or moisture. If liquid enters the unit, immediately disconnect the mains power.

No. You must never hang the BRITEQ BT-FOG3300 over an area where people can walk by or be seated, as hot liquid may accidentally drip from the nozzle.

It is recommended to clean the BRITEQ BT-FOG3300 every 100 hours of continuous operation to prevent obstructions in the heater, pump, and tubes.

You must use CE-certified smoke fluid with the BRITEQ BT-FOG3300. Always ensure the reservoir is not empty during operation to avoid damaging the pump.

Check that all screws are tightly fastened and free of corrosion, ensure the housings and suspension points are free of deformation, and verify that the mains cables are in impeccable condition.

For the XLR-3pin connector on the BRITEQ BT-FOG3300, Pin 1 is Ground, Pin 2 is Negative signal, and Pin 3 is Positive signal.

For the XLR-5pin connector on the BRITEQ BT-FOG3300, Pin 1 is Ground, Pin 2 is Negative signal, Pin 3 is Positive signal, and Pins 4 and 5 are not used.

The central hole in the hanging bracket of the BRITEQ BT-FOG3300 is designed for a rigging clamp, while the other two holes are provided for attaching an omega bracket.

Yes, the BRITEQ BT-FOG3300 supports continuous fogging at 50% output. When selecting the NONSTOP mode, the output volume is automatically reduced to enable continuous operation.

If the power cord of the BRITEQ BT-FOG3300 is squashed or damaged, switch off the unit immediately and have it replaced by the manufacturer or a qualified service agent to avoid hazards.

The electrical installation for the BRITEQ BT-FOG3300 must be carried out by qualified personnel according to local regulations, and the unit must be earthed.

First, enable WIRELESS CONTROL in the menu. Pull out the antenna on the remote for better range. Press the upper button on the remote to start fogging, and the lower button to stop the BRITEQ BT-FOG3300.

No. You must never repair a fuse or bypass the fuse holder. Always replace a damaged fuse in the BRITEQ BT-FOG3300 with a fuse of the same type and electrical specifications.

Never operate the BRITEQ BT-FOG3300 with an empty reservoir, as this can cause permanent damage to the pump.

You can secure the BRITEQ BT-FOG3300 either by putting a rigging clamp directly into the central hole of the hanging bracket or by fixing an omega clamp and rigging clamp to the bracket, ensuring the omega clamp is properly locked.

Allow the BRITEQ BT-FOG3300 time to adapt to the surrounding temperature before using it to prevent condensation from forming inside the unit, which can interfere with performance or cause damage.

No. You must never cover the ventilation openings of the BRITEQ BT-FOG3300, as this may lead to overheating.

Always allow the BRITEQ BT-FOG3300 to cool down for about 10 minutes before performing any servicing.

The housing of the BRITEQ BT-FOG3300 may reach temperatures up to 85 degrees Celsius, so avoid touching it with bare hands while in use.

To protect the environment, please recycle the packing material of the BRITEQ BT-FOG3300 as much as possible, and retain the original packaging for any future transportation needs.

Yes. The M-DMX USB-connector on the BRITEQ BT-FOG3300 is NOT used for software updates or PC connections. It is intended specifically for adding a wireless DMX dongle.

This message appears on the display of the BRITEQ BT-FOG3300 once the unit has reached its ideal working temperature and is prepared for operation.

Dispose of the BRITEQ BT-FOG3300 and any used batteries in an environment friendly manner and in accordance with your country’s regulations.

Before using the BRITEQ BT-FOG3300, check for any transportation damage. If any is found, do not use the device and consult your dealer. Verify that the carton includes the unit, the power cable, the wireless RF remote, and the operating instructions.

No. For safety reasons, it is prohibited to make unauthorized modifications to the BRITEQ BT-FOG3300.

It is strongly recommended that any internal cleaning of the BRITEQ BT-FOG3300 be carried out by qualified personnel only.

Always place the BRITEQ BT-FOG3300 on a flat, stable surface. Ensure the unit is positioned in a way that prevents liquid from dripping onto the audience.

Yes, use a good quality balanced cable to daisy chain the BRITEQ BT-FOG3300 with other DMX-compatible equipment.

The BRITEQ BT-FOG3300 features an LCD display with touch keys that allow you to scroll through the settings menu easily.

Yes, the BRITEQ BT-FOG3300 should be kept away from children, and it should not be operated by inexperienced persons.