BRITEQ BT-FOG1500 (01) PDF Document

The BRITEQ BT-FOG1500 includes high fog output, continuous fogging capabilities at 50 percent output, adjustable fog volume from 0 to 100 percent, multiple control methods, an LCD display with touch keys, a robust black housing, a solid suspension bracket, a protected connection compartment, and a strong fluid tank with level control.

Yes, the BRITEQ BT-FOG1500 supports continuous fogging when the output volume is set to 50 percent.

The fog volume on the BRITEQ BT-FOG1500 is adjustable from 0 percent to 100 percent.

The unit can be controlled in several ways:

1. Manually or with a timer using the on-board display and buttons.

2. Using the included RF-remote controller.

3. Via full DMX control with RDM support.

4. Using an optional wireless DMX USB-dongle connected to the dedicated M-DMX port.

The BRITEQ BT-FOG1500 is equipped with an LCD display with touch keys to easily scroll through the settings menu.

The suspension bracket is solid and features a serrated swivel mechanism for locking at different inclination angles. It is also prepared for use with an OMEGA bracket.

The indented compartment provides extra protection for the 3-pin and 5-pin XLR connectors, the PowerCON TRUE1 compatible input and output connectors, and the illuminated Power switch.

The BRITEQ BT-FOG1500 is equipped with a 1500W high-pressure diecast heater.

The fluid tank capacity of the BRITEQ BT-FOG1500 is 2.5 liters.

The BRITEQ BT-FOG1500 has an output volume of 31,000 cubic feet per minute, which is equivalent to 878 cubic meters per minute.

Before using the unit, check to ensure there is no transportation damage. If any damage is found, do not use the device and contact your dealer immediately.

The carton contains the following items:

1. The BRITEQ BT-FOG1500 unit.

2. A power cable.

3. A wireless RF remote controller.

4. Operating instructions.

No, the BRITEQ BT-FOG1500 is designed for indoor use only. To prevent fire or shock hazard, do not expose this appliance to rain or moisture.

The minimum distance between the fogger output nozzle and any surrounding objects must be more than 1 meter. Never hold hands close to the fogger output, as the fog is very hot and can cause serious burns.

To avoid internal condensation, allow the unit to adapt to the surrounding temperature when bringing it into a warm room after transport. Condensation can prevent the unit from working at full performance or may cause damage.

Locate the unit in a well-ventilated area, far away from any flammable materials and liquids. Do not cover any ventilation openings, as this can lead to overheating.

The maximum safe ambient operating temperature is 40 degrees Celsius. Do not operate the unit in ambient temperatures higher than this value.

The unit’s surface temperature can reach up to 85 degrees Celsius. Do not touch the housing with bare hands during operation.

You should never install the fogger directly above an audience because a small amount of hot liquid can always drip from the fog output nozzle, which can cause serious burns.

Allow the device to cool down for approximately 10 minutes before starting any service or maintenance work.

This unit must be earthed in order to comply with safety regulations. Always connect the power cable to a mains outlet with a proper earth connection.

Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a new fuse of the exact same type and electrical specifications.

Never hang the device over an area where people can walk by. Hot liquid may accidentally drip from the nozzle, which can cause serious burns.

The nozzle is the high-pressure fog output. Because it produces a hot, powerful output, you must maintain a minimum distance of 1 meter from it.

The reservoir must be filled with CE-certified smoke/fog fluid. Always ensure that the container is never empty during operation to avoid damaging the pump.

The center hole of the hanging bracket can be used to fix a standard rigging clamp, while the other two holes are designed for fixing an omega bracket.

The MODE button is used to navigate through the setup and options menu by pressing it several times.

The UP and TIMER button is used to increase values in the setup menu. When the display shows “READY TO WORK”, pressing this button activates the built-in timer function to execute your preconfigured interval, duration, and volume settings.

The FOG and DOWN button decreases values in the setup menu. When the display shows “READY TO WORK”, pressing this button starts the manual working mode, producing fog at your configured output volume.

The ENTER/STOP button is used to confirm a selected value in the setup menu. When the manual fog output or timer mode is active, pressing this button will stop the operation.

The mains output connector can be used to link and send power to other external devices up to a maximum load of 1500W.

First, locate and resolve the underlying issue that caused the breaker to trip. Once the problem is solved, press the breaker button to reset it.

The 3-pin and 5-pin female DMX output is used to connect the fogger to the next unit in the DMX chain. The 3-pin and 5-pin male DMX input is used to connect the unit directly to a DMX controller or the previous unit in the chain.

No, this USB connector is not used for updates or connecting to a PC. It is strictly used to add wireless DMX capability to the unit.

Connect an optional compatible wireless DMX dongle to the M-DMX USB input. You can then also share this wireless function with other DMX units connected to the physical DMX output port.

This message appears on the display as soon as the heating element has finished warming up and has reached its ideal working temperature, meaning the machine is ready to be used.

1. Press the MENU button until “DMX512 ADDRESS” is shown on the display.

2. Use the DOWN and UP buttons to adjust the DMX start address.

3. Press the ENTER button to confirm and save the setting.

1. Press the MENU button until “DMX MODE” is shown on the display.

2. Use the DOWN and UP buttons to toggle between 1 CH or 2 CH modes.

3. Press the ENTER button to confirm your selection.

1. Press the MENU button until “FOG OUTPUT” is shown on the display.

2. Use the DOWN and UP buttons to set your desired output volume.

3. Press the ENTER button to confirm.

When you select “NONSTOP” in the fog output settings, the output volume is automatically throttled down to ensure that the heater can run continuously without needing to stop to reheat.

1. Press the MENU button until “INTERVAL SET” is shown on the display.

2. Use the DOWN and UP buttons to set the desired interval time between 1 second and 600 seconds.

3. Press the ENTER button to confirm.

1. Press the MENU button until “DURATION SET” is shown on the display.

2. Use the DOWN and UP buttons to adjust the duration from 2 seconds to 255 seconds.

3. Press the ENTER button to confirm.

It is strongly recommended to keep the fluid sensor ON to prevent the unit from operating when the fog fluid container is empty, which can cause severe damage to the pump.

1. Press the MENU button until “FLUIR SENSOR” (fluid sensor) is shown on the display.

2. Use the DOWN and UP buttons to select ON (sensor active) or OFF (no fluid detection).

3. Press the ENTER button to confirm.

1. Press the MENU button until “WIRELESS CONTROL” is shown on the display.

2. Use the DOWN and UP buttons to select ON or OFF.

3. Press the ENTER button to confirm.

1. Press the MENU button until “KEY TONE” is shown on the display.

2. Use the DOWN and UP buttons to select the desired tone level from HIGH, MEDIUM, LOW, or OFF.

3. Press the ENTER button to confirm.

The unit has an initial warm-up time of approximately 6 minutes before it reaches the ideal operating temperature. When just powering on during a quick setup, it typically takes 3 to 4 minutes.

Press the FOG button on the control panel to trigger fog immediately. To stop the fog output, press the ENTER/STOP button. The output volume is influenced by your “FOG OUTPUT” setting.

1. Enable “WIRELESS CONTROL” in the settings menu.

2. Pull out the antenna on the remote controller for better range.

3. Press the upper button on the remote to start producing fog.

4. Press the lower button on the remote to stop the fogger.

When DMX is connected to the unit, the wireless remote receiver is automatically switched off.

The layouts are as follows:

XLR-3pin: Pin 1 = GND, Pin 2 = Negative signal (-), Pin 3 = Positive signal (+).

XLR-5pin: Pin 1 = GND, Pin 2 = Negative signal (-), Pin 3 = Positive signal (+), Pins 4 and 5 are not used.

To prevent signal reflections and erratic behavior of the light/fog effects due to interference, use a 90-ohm to 120-ohm terminator at the end of the chain. Never use Y-splitter cables.

In 1-Channel DMX Mode, the function is mapped as follows:

Channel 1 (FOG): DMX values from 000 to 255 adjust the fog output volume.

In 2-Channel DMX Mode, the channels are mapped as follows:

Channel 1 (FOG): DMX values from 000 to 255 adjust the fog output volume.

Channel 2 (MODE): DMX values from 000 to 005 place the unit in normal working mode. Values from 006 to 255 trigger continuous fog mode, where volume is automatically lowered when needed.

The rigging installation area must be able to hold a minimum point load of 10 times the weight of the device. Additionally, always use a certified safety cable that can support at least 12 times the weight of the device. This secondary safety attachment must limit any drop to a maximum of 20 cm in the event of a primary clamp failure.

The rigging can be performed in two ways:

1. By mounting a rigging clamp directly in the central hole of the hanging bracket.

2. By securing an omega clamp and a rigging clamp to the hanging bracket, ensuring the omega clamp is properly locked.

To prevent obstructions in the heater, pump, and tubes, the fogger should be cleaned on a regular basis. Every 100 hours of continuous operation is recommended.

To clean the unit, follow these steps:

Step 1. Switch the fogger off and unplug the mains cable.

Step 2. Remove the metal nozzle from the front of the unit and empty all fog liquid from the tank.

Step 3. Fill the tank with approximately 1 liter of a solution made of 80 percent distilled water and 20 percent white vinegar.

Step 4. Connect and turn on the fogger, then wait about 8 minutes for it to heat up.

Step 5. Run the fogger outdoors in continuous operation mode until the tank is completely empty.

Step 6. Reinstall the nozzle, clean any leftover residues, and refill the tank with fresh fog fluid.

The dimensions (Length x Width x Height) of the BRITEQ BT-FOG1500 are 43.5 x 36 x 20 cm, and it weighs 8 kg.

The unit requires an AC 220-240V, 50Hz mains power input.

During an inspection, check that all screws used for installing the device or its parts are tightly fastened and free of corrosion. Ensure that the housing, fixations, and suspension points are completely free from deformation, and verify that the mains power cable is in perfect condition with no damage.