BRAYER BR5032 (01) PDF Document

The BRAYER BR5032 is designed for removing lint that may accumulate on knitwear, helping your clothes look as good as new.

After transporting or storing the BRAYER BR5032 at negative temperatures, you must unpack the device and wait for at least 3 hours before using it.

Before the first use of the BRAYER BR5032, you should unpack the device, remove all packaging materials, study the manual, check the completeness of the set, and ensure the device is not damaged.

Insert the USB Type-C charging cable connector into the charging port of the BRAYER BR5032. Insert the second connector of the cable into a suitable power adapter (not included) with an output voltage of 5V and current of 1A, and plug it into a mains socket.

Yes, you can charge the BRAYER BR5032 battery by connecting the USB cable to a personal computer, laptop, or external power bank.

It is recommended to perform a 4 to 6 hour full charge of the BRAYER BR5032 battery before the first use.

Subsequent battery charging cycles for the BRAYER BR5032 should not exceed two hours.

Charge the BRAYER BR5032 battery at a temperature between +5° C and +35° C.

It is best to recharge the BRAYER BR5032 battery only after it has been fully depleted.

If you have not used the BRAYER BR5032 for a month or more, perform a full charge of the battery before use.

It is not recommended to use the BRAYER BR5032 on silk, terry cloth, plush, or furry fabrics.

No, do not remove lint from clothing while it is being worn. Always use hangers or a clothes rack instead.

Place the garment on a flat surface and straighten the fabric to remove any wrinkles before using the BRAYER BR5032.

Move the BRAYER BR5032 in circular motions and in various directions during operation.

Do not press the BRAYER BR5032 too hard against the fabric. Apply only gentle pressure with the metal mesh on the fabric.

Be especially careful when using the BRAYER BR5032 on edges, button areas, zippers, embroidery, appliqués, and similar features.

Remove the protection cap, remove the lint collection container by turning it counterclockwise, and empty out the debris.

Remove the protective metal mesh by turning it counterclockwise, then use the cleaning brush to clean the blade.

Yes, for easier cleaning of internal surfaces, the blade of the BRAYER BR5032 can be removed from the shaft of the electric motor by lifting it upward.

Wipe the outer surface of the BRAYER BR5032 body with a soft, slightly damp cloth. Avoid getting water inside the body and then wipe the surface dry. Do not use abrasive cleaning agents or solvents.

Carefully reinstall the blade onto the shaft of the electric motor by inserting it downward, reinstall the protective metal mesh and rotate it all the way clockwise, and then reinstall the lint collection container and rotate it all the way clockwise.

Before disposing of the BRAYER BR5032, fully deplete the rechargeable battery, extract it from the remover body, and follow the accepted rules for disposing of hazardous waste.

The nominal input power of the BRAYER BR5032 is 3 W.

The BRAYER BR5032 has a built-in Ni-Mh rechargeable battery: 2.4 V 2 x 600 mA/h.

Yes. Pay special attention to the metal mesh and blades of the BRAYER BR5032. Do not apply excessive pressure to the metal mesh during operation, and do not use the device if the metal mesh or blades are damaged.

No, using the BRAYER BR5032 for shaving or depilation is strictly prohibited.

No, it is not recommended to charge the BRAYER BR5032 battery during a thunderstorm.

If the BRAYER BR5032 falls into water while charging, immediately unplug the power adapter from the electrical outlet and only then extract the device from the water.

No, do not leave the BRAYER BR5032 unattended while it is operating.

During use, protect the BRAYER BR5032 from impacts, drops, vibrations, and other mechanical interference. Do not use it in places with high temperature and humidity.

Yes. Do not leave polyethylene bags or packaging film of the BRAYER BR5032 unattended as children may play with them, which poses a danger of suffocation.

No, the BRAYER BR5032 is not intended for use by children. Do not leave children unattended to prevent them from using the device as a toy.

Store the BRAYER BR5032 in a dry, cool place that is inaccessible to children and individuals with limited capabilities.

Periodically check the integrity of the BRAYER BR5032 battery charging cable. If it is damaged, replace it with a similar one.

No, do not attempt to repair or disassemble the BRAYER BR5032 by yourself. Seek professional help if there are any malfunctions or after the device has fallen.

The BRAYER BR5032 requires regular cleaning of the lint collection container, the blade, and the internal surface around the motor shaft using the provided cleaning brush, followed by wiping the outer body with a damp cloth.

Remove the lint collection container of the BRAYER BR5032 by turning it counterclockwise.

Remove the protective metal mesh of the BRAYER BR5032 by turning it counterclockwise.

The BRAYER BR5032 delivery set includes:

1. Lint remover (1 pc.)

2. USB Type-C charging cable (1 pc.)

3. Cleaning brush (1 pc.)

4. Instruction manual (1 pc.)

No, the BRAYER BR5032 is intended for domestic use only. Using it for commercial or laboratory purposes is strictly prohibited.

The operating life of the BRAYER BR5032 is 3 years.

No, do not discard the BRAYER BR5032 or its batteries with usual household waste. Take them to specialized stations for further recycling to prevent environmental or health damage.

The BRAYER BR5032 requires a power adapter (not included) with an output voltage of 5V and a current of 1A.

No, do not use abrasive cleaning agents or any solvents to clean the BRAYER BR5032.

You turn on the BRAYER BR5032 using the power switch.

Turn off the BRAYER BR5032 after use using the power switch.

Do not charge the rechargeable battery of the BRAYER BR5032 in places with high humidity and temperature. Charge the battery at a temperature from +5° C to +35° C and relative humidity no more than 80%.

The BRAYER BR5032 is not a toy. Exercise extra caution if children or people with disabilities are in close proximity to the operating device, and keep the device in areas inaccessible to children when not in use.

Yes, before storing the BRAYER BR5032, perform its cleaning.

The full charging time for the BRAYER BR5032 is 6-8 hours.