BRAUN 5090CC (01) PDF Document

Please observe the following safety warnings when using your BRAUN 5090CC:

• Your appliance is provided with a special cord set, which has an integrated Safety Extra Low Voltage power supply. Do not exchange or tamper with any part of it, otherwise there is risk of an electric shock. Only use the special cord set provided with your appliance.

• If the appliance is marked C 492, you can use it with any Braun power supply coded 492-XXXX.

• Do not shave with a damaged foil or cord.

• The shaver is suitable for cleaning under running tab water. Detach the shaver from the power supply before cleaning it in water.

• Model 5040s w&d only: This appliance is suitable for cleaning under running water and use in a bath or shower. For safety reasons it can only be operated cordless.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the safe use of the appliance and understand the hazards involved.

• Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children unless they are older than 8 years and supervised.

• To prevent the cleaning fluid from leaking, ensure that the Clean&Charge Station is placed on a flat surface. When a cleaning cartridge is installed, do not tip, move suddenly or transport the station in any way as cleaning fluid might spill out of the cartridge. Do not place the station inside a mirror cabinet, nor place it on a polished or lacquered surface.

• The cleaning cartridge contains a highly flammable liquid so keep it away from sources of ignition. Do not expose to direct sunlight and cigarette smoking nor store it over a radiator.

• Do not refill the cartridge and use only original Braun refill cartridges.

Prior to first use, remove the protection foil if any from the shaver display and connect the shaver to an electrical outlet using the special cord set (10). When the shaver is connected to an electrical outlet, it may take some minutes until the display illuminates.

• A full charge provides up to 45 minutes of cordless shaving time. This may vary according to your beard growth and environmental temperature.

• Recommended ambient temperature for charging is 5 °C to 35 °C. The battery may not charge properly or at all under extreme low or high temperatures. Recommended ambient temperature for shaving is 15 °C to 35 °C.

• Do not expose the appliance to temperatures higher than 50 °C for extended periods of time.

The shaver display (5) shows the charge status of the battery.

During charging: The battery symbol will blink. For the 5090cc model, the respective battery segment will blink.

Fully charged (shaver is connected to an electrical outlet): The battery symbol will light up for a few seconds. For the 5090cc model, all battery symbols will light up for a few seconds.

Low charge: The low-charge light flashes red when the battery is running low. You should be able to finish your shave. When switching off the shaver, a beep sound reminds of the low charge status.

The cleaning indicator lights up when the shaver needs to be cleaned in the Clean&Charge Station. This feature is only available on models 5090cc, 5070cc, and 5050cc.

The lock symbol lights up when the shaver has been locked to avoid unintended starting of the motor (e.g. for storing it in a suitcase).

Activation: By pressing the on/off switch (4) for 3 seconds the shaver is locked. This is confirmed by a beep sound and the lock symbol in the display. Afterwards the display turns off.

Deactivation: By pressing the on/off switch for 3 seconds the shaver is unlocked again.

For best results, Braun recommends you to follow 3 simple steps:

1. Always shave before washing your face.

2. At all times, hold the shaver at the right angle (90°) to your skin.

3. Stretch your skin and shave against the direction of your beard growth.

To shave hard-to-reach areas (e.g. under the nose), slide the MultiHeadLock switch (3) down to lock the shaver head. The shaver head can be locked in five positions. To change position, move the shaver head with your thumb and forefinger back or forth. It will automatically click into the next position.

To set it back into the pivoting position, the MultiHeadLock switch needs to be slid up again.

For models 5090cc/5070cc/5050cc: For automatic cleaning in the Clean&Charge Station the head lock should be released.

To trim sideburns, moustache or beard, press the release button (8a) and slide the long hair trimmer (6) upwards.

Yes, for models 5090cc/5070cc/5050cc/5030s/5020s, if the shaver has run out of power (discharged), you may also shave with the shaver connected to an electrical outlet via the special cord set.

Cleaning under running water:

1. Switch the shaver on (cordless) and rinse the shaver head under hot running water until all residues have been removed. You may use liquid soap without abrasive substances. Rinse off all foam and let the shaver run for a few more seconds.

2. Next, switch off the shaver, press the release button (2) to remove the Foil & Cutter cassette (1) and let it dry.

3. If you regularly clean the shaver under water, then once a week apply a drop of light machine oil on top of the Foil & Cutter cassette.

Cleaning with a brush:

1. Switch off the shaver. Remove the Foil & Cutter cassette (1) and tap it out on a flat surface.

2. Using the brush, clean the inner area of the pivoting head. Do not clean the cassette with the brush as this may damage it!

1. Remove the protection foil from the Clean&Charge Station display.

2. Using the special cord set (10), connect the station power socket (12) to an electrical outlet.

3. Press the lift button (13) at the rear side of the Clean&Charge Station to lift up the housing.

4. Hold the cleaning cartridge (17) down on a flat, stable surface (e.g. table).

5. Carefully remove the lid from the cartridge.

6. Slide the cartridge from the rear side into the base of the station until it snaps into place.

7. Slowly close the housing by pushing it down until it locks.

Insert the shaver head down into the cleaning station. The shaver needs to be dry and free from any foam or soap residue.

The contacts (7) on the back of the shaver need to align with the contacts (14) in the station. Push the shaver in the correct position. A beep sound confirms that the shaver sits properly in the station. Charging will start automatically.

When the cleaning indicator lights up in the shaver display, insert the shaver into the Clean&Charge Station, upside down and with the front showing (with released head lock/contact alignment/beep sound).

Cleaning programs for model 5090cc:

The hygiene status will be analyzed and one of the following program indicators will light up:

• one drop: short economical cleaning

• two drops: normal level of cleaning

• three drops: high intensive cleaning

Models 5070cc/5050cc include one standard cleaning program.

Start automatic cleaning:

Press the start button (16). If the status light (15a) does not shine (the station switches to stand-by after ca. 10 minutes), press the start button twice. Otherwise cleaning will not start. For best shaving results, we recommend cleaning after each shave.

Hold the Clean&Charge Station with one hand and tilt the shaver slightly to the front to release it.

When the level indicator lights up permanently red, the remaining fluid in the cartridge is sufficient for about 3 more cycles. When the level indicator blinks red, the cartridge needs to be replaced (about every 4 weeks when used daily).

The hygienic cleaning cartridge contains ethanol or isopropanol. Each cartridge, if not used daily, should be replaced after approximately 8 weeks to ensure optimal disinfection.

To replace it, press the lift button (13) to open the housing, wait a few seconds, and then remove the used cartridge. Before discarding the used cartridge, close the openings with the lid of the new cartridge.

The product contains batteries and/or recyclable electric waste. For environment protection, do not dispose of it in household waste, but for recycling take it to electric waste collection points provided in your country.

The cleaning cartridge can be disposed of with regular household waste.

Braun recommends changing your shaver’s Foil & Cutter cassette every 18 months to maintain maximum performance. Available accessories include:

• Foil & Cutter cassette: 52S/52B

• Cleaning cartridge Clean&Charge Station: CCR

• Braun Shaver cleaner spray

This may be due to one of two reasons:

1. The travel lock is activated. To fix this, press the on/off switch for 3 seconds to unlock the shaver.

2. For the Wet&dry model 5040s, it may be plugged in. Unplug the shaver. This appliance can only be operated cordless.

The ambient temperature is out of the valid range. The recommended ambient temperature for charging is 5°C to 35°C.

There are several possible reasons:

1. The shaver is not placed properly in the Clean&Charge station. Ensure the contacts of the shaver align with the contacts in the station.

2. Charging could be delayed, for example, after long storage. Wait a few minutes; if charging will start, it will do so automatically.

3. The ambient temperature is out of the valid range. The recommended ambient temperature for charging is 5°C to 35°C.

This could be due to the following:

1. Shaver head is cleaned with water only. When cleaning the shaver head with water only, use hot water and from time to time some liquid soap (without abrasive substances). Remove foil & cutter cassette to let it dry.

2. Cleaning cartridge is in use for more than 8 weeks. Change the cleaning cartridge at least every 8 weeks.

This could be for two reasons:

1. The shaver head is regularly cleaned with water but not lubricated. If the shaver is regularly cleaned with water, apply a drop of light machine oil on top of the foil once a week for lubrication.

2. The foil and cutter are worn, which requires more power for each shave. Renew the foil & cutter cassette.

Possible reasons include:

1. Shaving system is clogged. Soak the foil & cutter cassette into hot water with a drop of liquid dish soap. Afterwards rinse it properly and tap it out. Once dry, apply a drop of light machine oil on the foil.

2. Foil and cutter are worn. Renew the foil & cutter cassette.

The foil and cutter are worn, which requires more power for each shave. To resolve this, you should:

• Renew the foil & cutter cassette.

• Regularly oil the shaving system, especially when cleaning with water only.

This could be due to several reasons:

1. Drying time after automatic cleaning was too short. Clean the shaver directly after shaving to allow enough time for drying.

2. The drain of the Clean&Charge Station is clogged. Clean the drain with a wooden toothpick.

3. The cleaning cartridge has been used for quite a while. The ethanol/isopropanol proportion has decreased while the oil proportion has increased. Remove residue with a cloth.

There are several possible causes:

1. Shaver is not placed properly in the station. Insert the shaver into the Clean&Charge station, ensuring the contacts align.

2. The cleaning cartridge does not have enough fluid. If the level indicator blinks red, insert a new cleaning cartridge.

3. The appliance is in stand-by mode. Press the start button again.

The drain of the Clean&Charge station is clogged. To fix this, clean the drain with a wooden toothpick and regularly wipe the tub clean.