BLACK & DECKER FS100SF (01) PDF Document

Attach the handle to the extension assembly by turning the handle counter-clockwise to loosen the ring adjustment. After attaching the handle assembly, turn the handle clockwise to tighten. Be sure the handle is fully seated.

Insert the correct driver bit tip for the screws being used (Phillips / Robertson Head) by placing the bit at the quick-change bit holder and retracting the quick-change barrel.

Insert the bit through the main body as shown, making sure the front assembly hole aligns with the sliding barrel and secure the assembly unit until it clicks into place.

Insert the clear tube through the front and rear supports and into the sliding barrel until it stops; a slight rotational movement can help.

Attach the drill chuck to the hex shank shaft.

Remove the clear tube from the sliding barrel. Hold the unit as shown, press in the tab and turn in the direction of the arrow to release.

Remove the main body assembly and place it aside.

Press the barrel of the quick-change bit holder and remove the bit, insert the replacement, reverse steps to reinstall.

Reattach the main body assembly making sure to align the clear tube with the sliding barrel.

Check for correct driver bit tip for screws being used by retracting the sliding barrel. (See “Changing A Drive Bit”)

Set depth stop to desired counter sink depth.

Holding the unit vertically, drop screws through the screw filter. Note: Do not overfill the tube as it may jam the screw filter. Completely depress and release sliding barrel once by pressing onto horizontal surface to load first screw into barrel.

To drive screws, locate tip on workpiece, hold drill and feeder assembly vertically, squeeze trigger while pushing on drill. Stop when ratcheting sound starts (drive bit has disengaged from screw head at set depth.)

Always hold unit securely with two hands in a vertical downward position only. Keep hands and feet away from main body assembly when tool is depressed. Note that the weight of some heavier drills is enough to cause tool to depress.

Always remove screws from tubes by pulling tube from sliding barrel, allowing screws to fall from bare end. DO NOT try to remove screws through the screw filter at other end.

To remove screws which have become dislodged, lift the clear plastic window at the head of the sliding barrel.

Use of a variable speed drill at medium to low speed.

If the unit tends to vibrate after engaging the drill’s chuck, loosen the chuck jaws and reattach.

Do not use the unit with a hammer drill option engaged.

For best results, use ONLY with drywall and decking type screws number #6 & #8 Phillips or Robertson head, 1.5 to 3 inches in length.

If a screw head has the option to use both Phillips and Robertson square bit, then it is recommended to use as a first option the square bit to get the full advantages of the depth adjuster.

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. Periodically clean any metal screw fragments from tool.

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts.

Recommended accessories for use with your tool are available from your local dealer or authorized service center.

The use of any accessory not recommended for use with this tool could be hazardous.

Attach the handle to the extension assembly by turning the handle counter-clockwise to loosen the ring adjustment. After attaching the handle assembly, turn the handle clockwise to tighten. Be sure handle is fully seated.

Remove the clear tube from the sliding barrel. Hold the unit as shown, press in the tab and turn in the direction of the arrow to release.

Set depth stop to desired counter sink depth.

The BLACK & DECKER FS100SF is for use ONLY with drywall and decking type screws number #6 & #8 Phillips or Robertson head, 1.5 to 3 inches in length. Other screws may jam.

Do not overfill the tube as it may jam the screw filter.

Completely depress and release sliding barrel once by pressing onto horizontal surface to load first screw into barrel.

After use, always remove drill from tool. Do not store with drill attached to hex shaft. Tool with attached drill can more easily fall if bumped.

If tool is damaged or not functioning properly, have it serviced before using. Many accidents are caused by poorly maintained tools.

Use of a variable speed drill at medium to low speed.

If the unit tends to vibrate after engaging the drill’s chuck, loosen the chuck jaws and reattach.

Do not use the unit with a hammer drill option engaged.

If the unit tends to vibrate after engaging the drill’s chuck, loosen the chuck jaws and reattach.

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. Periodically clean any metal screw fragments from tool.

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts.

If your warning labels become illegible or are missing, call 1-800-544-6986 for a free replacement.

If tool is damaged or not functioning properly, have it serviced before using. Many accidents are caused by poorly maintained tools.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.