BEKO HII 64700 UFT (01) PDF Document

General warnings for the BEKO HII 64700 UFT hob include:

• Do not let any objects fall on the hob. Even small objects such as saltshakers may damage the hob. Do not use cracked hobs. Water may seep through these cracks and cause a short circuit. If the surface is damaged in any way (e.g. visible cracks), turn off the fuse first, then call the authorized service to unplug the product to reduce the risk of electric shock.
• Do not use unbalanced and easily tilting pots/pans on the hob.
• Do not heat the pots/pans and pots empty. The pots and the appliance may be damaged.
• Always turn off the hob’s burners after each use.
• You shall damage the appliance if you operate the hobs without any pot or pots/pans. Always turn off the hobs after each operation.
• After each use the cooking surface will be hot, so do not put the plastic pots/pans on the cooking surface. Clean such material on the surface immediately.
• Sudden temperature changes on the glass cooking surface may cause damage, be careful not to spill cold liquids during cooking.
• Put a sufficient amount of food in pots and pans. Thus, you can prevent food from pouring forth out of the pots/pans and will not need to clean unnecessarily.
• Do not place the covers of pots and pans on burners/zones.
• Place the pots by centering them on the burners/zones. If you wish to place a pot on a different burner/zone, do not slide it towards the desired burner; rather, lift it first and then put it on the other burner.

The induction hob on the BEKO HII 64700 UFT is like an open circuit. The circuit completes when a cooking pots/pans suitable for induction cooking is placed on it and an electronic system below the glass surface generates a magnetic field. The metal base of the pots/pans is heated by taking energy from this magnetic field. Thus, the heat is not generated on the surface of the hob, but directly on the pots/pans above it. The glass surface is heated with the heat of the cooking pots/pans.

Induction hobs on the BEKO HII 64700 UFT offer some advantages as the heat is transferred directly to the cooking pots/pans:

• Foods that overflow during cooking do not burn rapidly as the glass cooking surface is not heated directly. It is cleaned more easily.
• Cooking shall be faster as the heat is generated directly on the cooking pots/pans. Thus, it saves time and energy with respect to other hob types.
• As the heat is given directly to the cooking pots/pans, there is no heat loss, and it provides a more efficient cooking.
• The fact that the heat transfer stops and the cooking surface is not heated directly when the cooking pots/pans is removed from the cooking surface provides a safer use against possible accidents while cooking.

For a safe operation of the BEKO HII 64700 UFT induction hob:

• Do not select high heating levels when using non-sticking cooking pots/pans coated with little amount of oil or used without oil (teflon type).
• Do not use glass cooking surface as a surface where you can place something on it or as a cutting surface.
• Do not place metal objects such as cutlery or pot lids on your hob as they may get hot.
• Never use aluminium foil for cooking. Never place food wrapped in aluminium foil on the induction zone.
• Keep magnetic objects such as credit cards or tapes away from the hob while it is operating.
• If there is an oven under your hob and it is being operated, the sensors on the hob may reduce the cooking level or turn off the hob.
• Your BEKO HII 64700 UFT hob has an automatic shut-off system. However, if you use thin based pots for your cooking, these pots shall heat up very quickly and the bottom of the pan may melt and damage the cooking surface and the appliance before the automatic shut-off system is activated.

For the BEKO HII 64700 UFT induction hob, you shall use ferromagnetic, quality cooking pots/pans which bear a label or warning that it is compatible for induction cooking only. Generally, the higher the iron content, the better the cooking pots/pans shall perform. The base diameter of the cooking pots/pans shall match the induction zone. Suggested dimensions are listed below in the following table:

Table – Recommended cooking pots/pans sizes

Suitable pots/pans for the BEKO HII 64700 UFT include:

• Cast iron pots/pans
• Enamelled steel pots/pans
• Steel and stainless steel pots/pans (with label or warning indicating that it is induction compatible)

Unsuitable pots/pans for the BEKO HII 64700 UFT include:

• Aluminium pots/pans
• Copper pots/pans
• Brass pots/pans
• Glass pots/pans
• Pottery
• Ceramic and porcelain

Recommendations:

• Use flat bottomed cooking pots/pans only. Do not use pots/pans with convex or concave bases.
• Use cooking pots/pans with thick, processed bases only. If you use thin based pots, these pots shall heat up very quickly and the bottom of the pan may melt and damage the cooking surface and the appliance before the automatic shut-off system is activated. Sharp edges may cause scratches on the surface.
• The bases of some cooking pots/pans have a smaller ferromagnetic field than its true diameter. Only this area is heated by the hob. Therefore, the heat is not evenly distributed and the cooking performance is decreased. Moreover, such cooking pots/pans may not be detected by large induction hobs. Thus, the cooking hob shall be selected according to the size of the ferromagnetic field.
• Some cooking pots/pans have a base that contains non-ferromagnetic materials such as aluminium. These types of cooking pots/pans may not heat adequately or may not be detected by the induction hob at all. In some cases, a bad pots/pans warning may appear.

To test whether your pot is compatible with cooking with an induction hob on the BEKO HII 64700 UFT using the methods below:

1. It is compatible if the base of your pot holds a magnet.
2. It is compatible if a symbol, or a symbol, or a symbol does not flash when you place your pot on the induction hob and turn on the hob.

Before you start using your BEKO HII 64700 UFT product, it is recommended to do the following for the first cleaning:

1. Remove all packaging materials.
2. Wipe the surfaces of the product with a wet cloth or sponge and dry with a cloth.

NOTICE: The surface might get damaged by some detergents or cleaning materials. Do not use aggressive detergents, cleaning powders/creams or any sharp objects during cleaning.

NOTICE: Smoke and smell may emit for a couple of hours during the initial operation. This is quite normal. Ensure that the room is well ventilated to remove the smoke and smell. Avoid directly inhaling the smoke and the smell that emits.

To turn the hob off on the BEKO HII 64700 UFT:

1. Touch the On/Off key on the control panel.

The hob turns off and returns to stand-by mode.

There is a heat indicator for each hob zone on the control panel of the BEKO HII 64700 UFT. This indicator indicates that the hob is still hot when it is turned off. Do not touch the relevant hob(s) until the remaining heat indicator disappears. The symbols and descriptions are:

In case of a power failure, the remaining heat indicator does not illuminate and warn the user against hot hobs.

To turn on a cooking zone and set the temperature level on the BEKO HII 64700 UFT hob:

1. Turn the hob on by touching the On/Off key. The “0” symbol appears on the hob zone displays.
2. Depending on the area you want to turn on, by touching on the setting area or by sliding your finger on the area, set the temperature level between “0” and “9”. While the temperature level is increased as 1,2,3…19 on some models, it may be increased as 1,1.,2,2. 9. on some other models. This varies as per product model.

A selected hob zone on the BEKO HII 64700 UFT may be turned off in 2 different ways:

1. By setting the temperature as “0”. You may turn off the hob by reducing the temperature setting to “0”.
2. Using the timer off function for the desired hob zone. When the time is off, the timer turns off the hob connected to it. All displays indicate “0” or “00”. The Timer symbol on the hob display disappears. The setting of the timer for the hob zone is described in the following chapters.

To activate the Cleaning Lock on the BEKO HII 64700 UFT while the hob is on:

1. Touch and hold on the Cleaning Lock key when the hob is on. The Cleaning Lock light will illuminate. The symbol for Cleaning Lock will be displayed on the displays of the hob zones. No key other than the Cleaning Lock key may be operated during this period.

To deactivate the Cleaning Lock on the BEKO HII 64700 UFT, touch and hold on the Cleaning Lock key to disable cleaning lock. The Cleaning Lock light will fade and cleaning lock will be disabled.

To activate the Key Lock on the BEKO HII 64700 UFT while the hob is on or off:

1. To activate the key lock, touch the Key Lock key until one signal is heard. The light of the Key Lock key shall flash and all cooking zones shall be locked.

Only the On/Off key operates while the key lock is active. When you touch any other key, the light of the Key Lock key flashes to indicate that the key lock is active. If you turn off the hob while the keys are locked, the key lock shall be deactivated to turn the hob on again.

To deactivate the Key Lock on the BEKO HII 64700 UFT:

1. Touch and hold the Key Lock key until one signal is heard. The operation shall be confirmed with an audible signal. The light of the Key Lock key will fade and the key lock will be deactivated.

To activate the timer on the BEKO HII 64700 UFT hob:

1. Turn the hob on by touching the On/Off key.
2. Depending on the area you want to turn on, by touching on the setting area or by sliding your finger on the area, set the temperature level you want.
3. Activate the timer by touching the Timer key. The “00” will illuminate and the Timer symbol starts to blink.
4. There are 4 activity LEDs around the “00” displayed on the timer display. For the hob zone to be set a timer, touch the Timer key to select the relevant hob zone side.
5. Set the desired period by touching the Timer increase key or Timer decrease key. You may also advance the timer faster by touching the Timer increase key or Timer decrease key for a long period of time. The Timer symbol illuminates solidly after flashing on the hob zone display for a specific period of time. When the Timer symbol illuminates solidly, this shows that the function is activated.

The timer may only be used for hobs that are being operated. Repeat the procedure above for other hobs that you want to set a timer for. Timer cannot be set without selecting the hob zone and the temperature level of the hob zone.

When the set time expires on the timer of the BEKO HII 64700 UFT hob, the hob turns off automatically and an audible warning is given. Touch any key to turn off the audible warning.

If the timer on the BEKO HII 64700 UFT is turned off prematurely, the hob continues to operate with the set temperature until it is turned off. You can turn off the timer by reducing the timer setting to “00” level:

1. Select the timer of the relevant hob by touching the Timer key.
2. Wait until the “00” symbol is displayed on the timer display by touching the Timer decrease key to reduce the value. You may also advance the timer faster by touching the Timer increase key for a long period of time. The Timer symbol flashes for a specific period of time on the hob zone display, then it turns off completely and the timer is cancelled.

With the Stop function on the BEKO HII 64700 UFT hob, you may stop all functions operating at the hob (excluding the timer) to the 1st level for a while.

If the timer is set for any hob zone, the timer resumes to operate during the stop function.

1. Touch the Stop function key while your hob is on. All hobs that are being operated continue to operate at 1st level.
2. Touch the Stop function key again to operate all stopped hob cooking zones with their previous settings.

To set the total power of the BEKO HII 64700 UFT hob as you desire with the Power management setting (CF1) function:

1. Turn on the hob by touching the On/Off key, and turn it off by touching the On/Off key again.
2. Within 10 seconds after turning off the product, touch the Power management setting keys respectively. On the timer display CF1, on left rear hob display “9” will be displayed.
3. By touching on the setting area of the left rear hob setting area or by sliding your finger on the area, set the power level between “1” and “9” (see the Power management level table below).
4. Confirm the selected level setting by touching the On/Off key.

Your hob will turn off and will start to operate with the total power setting at the selected level. “Power management” includes 9 different power levels (see Table – Power management level):

Total power value for the power management level of 5, 6, 7, 8, 9 is 3.6 kW in products that with the maximum total power consumption of 3.6 kW.

To set the cooking-end signal time of the BEKO HII 64700 UFT hob using the Cooking-end audible signal time setting (F2) function:

1. Turn on the hob by touching the On/Off key, and turn it off by touching the On/Off key again.
2. Within 10 seconds after turning off the product, touch the Power management setting keys respectively. Default setting CF1 will be displayed on the timer display.
3. For cooking-end audible signal setting, touch the Timer key once. On the timer display CF2, on the left rear hob display “2” will be displayed.
4. By touching on the setting area of the left rear hob setting area or by sliding your finger on the area, set the signal time setting between “0” and “3” (see Table – Cooking-end audible signal time setting).
5. By touching the On/Off key, confirm the cooking-end audible signal time setting.

Your hob will turn off and will start to operate with the signal time setting at the selected level. The factory default value for the cooking-end audible signal time setting is standard 2nd level.

Table – Cooking-end audible signal time setting

To set the Hob-Hood connection setting (F3) on the BEKO HII 64700 UFT to connect the hob and hood to allow them to operate together automatically:

1. Turn on the hob by touching the On/Off key, and turn it off by touching the On/Off key again.
2. Within 10 seconds after turning off the product, touch the Power management setting keys respectively. Default setting CF1 will be displayed on the timer display.
3. Touch twice on the Hob-Hood connection key for the Hob-Hood connection setting. On the timer display CF3, on the left rear hob display “4” will be displayed.
4. By touching on the setting area of the left rear hob setting area or by sliding your finger on the area, set the hood operation level between “0” and “7” (see Table – Hood operation level).
5. By touching the On/Off key, confirm the hob-hood connection setting.

Your hob will turn off and will start to operate with the selected hob operation level.

Table – Hood operation level

Setting hood operation level over the hob: With this setting, you may set hood operation level over the hob.

1. Turn the hob on by touching the On/Off key for 3 seconds.
2. Touch the Hob-Hood connection key. The light of the Hob-Hood connection key will go off.
3. Touch the Hob-Hood connection key until the desired operation level for the hood is reached.

The technical specification for the Product external dimensions (height/width/depth) of the BEKO HII 64700 UFT is 45,2 mm*/590 mm/520 mm. The asterisk (*) indicates that the height of the hob specified in the technical table is the base cover height of the product.

The technical specification for the Hob installation dimensions (width/depth) of the BEKO HII 64700 UFT is 560 (+2) mm /490 (+2) mm.

The technical specification for the Voltage / frequency of the BEKO HII 64700 UFT is 1N~ 220-240 V/2N~ 380-415 V ;50/60 Hz.

The technical specification for the Cable type and cross section used / suitable for use in the product for the BEKO HII 64700 UFT is min. H05V2V2-F 5 x 1,5 mm².

The technical specification for the Total power consumption of the BEKO HII 64700 UFT is max. 7,4 kW.

The technical specifications for the Rear left Induction cooking zone on the BEKO HII 64700 UFT are:

The technical specifications for the Front left Induction cooking zone on the BEKO HII 64700 UFT are:

The technical specifications for the Front right Induction cooking zone on the BEKO HII 64700 UFT are:

The technical specifications for the Rear right Induction cooking zone on the BEKO HII 64700 UFT are:

If the mains fuse for the BEKO HII 64700 UFT is defective or has tripped, you should check fuses in the fuse box. If necessary, replace or reset them.

If the product of the BEKO HII 64700 UFT is not plugged into the (grounded) socket, you should check the plug connection.

If the buttons/knobs/keys on the control panel of the BEKO HII 64700 UFT do not function, check if your product is equipped with key lock function, as keylock may be enabled. If so, please disable it.

If the display of the BEKO HII 64700 UFT does not light up when you switch the hob on again, disconnect the appliance at the circuit breaker. Wait minimum 20 seconds and then reconnect it.

If the Overheat protection is active on the BEKO HII 64700 UFT, allow your hob to cool down.

If the cooking pot is not suitable on the BEKO HII 64700 UFT, check your pot.

If the “” or “” symbol appears on the cooking zone display of the BEKO HII 64700 UFT:

• You have not placed the pot on the active cooking zone. Check if there is a pot on the cooking zone.
• Your pot is not compatible with induction cooking. Check if your cooking pot is compatible with induction hob.
• The cooking pot is not centered properly or the bottom surface of the pot is not wide enough for the cooking zone. Choose a pot wide enough and center the pot on the cooking zone properly.
• Cooking pot or cooking zone is overheated. Allow them to cool down.

If the selected cooking zone on the BEKO HII 64700 UFT suddenly turns off during operation:

• Cooking time for the selected cooking zone may be over. You may set a new cooking time or finish cooking.
• Overheat protection is active. Allow your hob to cool down.
• An object may be covering the touch control panel. Remove the object on the panel.

If the pot does not get warm even if the cooking zone is on for the BEKO HII 64700 UFT:

• Your pot is not compatible with induction cooking. Check if your cooking pot is compatible with induction hob.
• The cooking pot is not centered properly or the bottom surface of the pot is not wide enough for the cooking zone. Choose a pot wide enough and center the pot on the cooking zone properly.

If the Cooling fan continues operating although the hob is turned off on the BEKO HII 64700 UFT, this is not a fault. The cooling fan will continue operating until the electronics in the hob cools down to a suitable temperature.

If Error code E 22 or E 26 appears on the BEKO HII 64700 UFT, the error reason is: Induction hob is overheated. The possible solution is: Turn the induction cooker off and wait until it is cooled down. The error shall be resolved when temperature of the hob comes down below the limits.

If Error code E 46 appears on the BEKO HII 64700 UFT, the error reasons are: One or more keys are kept pressed for more than 10 seconds, or An object is left on the control panel or the control is exposed to vapour. The possible solutions are: The problem shall be resolved when you remove your hand from the hob, or The problem shall be resolved when the control panel is cleaned.

If Error code E 47 appears on the BEKO HII 64700 UFT, the error reason is: A pot suitable for induction heating is not used. The error shall be resolved when a pot suitable for induction heating is used.

If Error code E 1 – E 15 appears on the BEKO HII 64700 UFT, the error reason is: Communication error on induction hob. The possible solution is: Turn the induction hob off and operate again after 30 seconds. Contact the authorized dealership if the issue is resumed.

If Error code E 16 – E 21 appears on the BEKO HII 64700 UFT, the error reason is: Temperature sensor error on induction hob. The possible solution is: Turn the induction hob off and operate again after 30 seconds. Contact the authorized dealership if the issue is resumed.

If Error code E 23 or E 24 appears on the BEKO HII 64700 UFT, the error reason is: Software error on induction hob. The possible solution is: Turn the induction hob off and operate again after 30 seconds. Contact the authorized dealership if the issue is resumed.

If Error code E 25 appears on the BEKO HII 64700 UFT, the error reason is: Fan operation error on induction hob. The possible solution is: Turn the induction hob off and operate again after 30 seconds. Contact the authorized dealership if the issue is resumed.

If Error code E 31 – E 45 appears on the BEKO HII 64700 UFT, the error reason is: Electronic board hardware error on induction hob. The possible solution is: Turn the induction hob off and operate again after 30 seconds. Contact the authorized dealership if the issue is resumed.

If Error code E 48, E 49, or E 51 appears on the BEKO HII 64700 UFT, the error reason is: Sensor error on induction hob. The possible solution is: Sensor equipment shall be rendered compatible for the operating conditions. Contact the authorized dealership if the issue is resumed.

If Error code E 52 – E 57 appears on the BEKO HII 64700 UFT, the error reason is: High temperature error on induction hob. The possible solution is: Turn the induction hob off and wait until it is cooled down. The error shall be resolved when temperature of the sensor comes down below the limits. Contact the authorized dealership if the issue is resumed.

If the FF symbol appears on the BEKO HII 64700 UFT display, the error reasons are: Any one of the keys may have been touched long, A cooking pot may have come over the control unit, or There may be food/liquid poured over the control unit. The possible solutions are: When long touching on one of the keys was stopped, When the cooking pot over the control unit is lifted, or Error will disappear when the food/liquid residues are cleaned.

Some sounds may be heard from the BEKO HII 64700 UFT cooker while cooking, due to the composition of the cooking vessel. These sounds are normal and are a part of induction technology. Possible noises and reasons include:

• Fan noise: The cooker is equipped with a fan that activates automatically according to the temperature of the appliance. The fan has various operating levels and operates at different levels as per the temperature.
• Lower buzz like the operating noise of a transformer: This is due to the nature of the induction technology. As the heat is transmitted directly to the base of the cooking vessel, such buzz sounds may be heard as per the material of the cooking vessel. Thus, different noises may be heard with different cookware.
• Cracking noise: The reason of this is the structure and material of the base of the cooking vessel. A cracking sound may be heard if the cooking vessel is made of various layers with different materials.
• Whining noise: A whining sound may be heard when two cooking zones on the same side of the cooker are used to cook with different cooking levels.

The following suggestions will help you use your BEKO HII 64700 UFT product in an ecological and energy-efficient way:

• Defrost frozen food before cooking.
• Turn off the product 5 to 10 minutes before the end time of cooking for prolonged cooking. Now you can save up to 20% electricity by using heat.
• Use pots / pans with a size and lid suitable for the hotplate. Always choose the right size pot for your meals. More than necessary energy is needed for containers of the wrong size.
• Keep hob cooking surfaces and pot bases clean. Dirt reduces the heat transfer between the cooking area and the pot base.

The hob control on the BEKO HII 64700 UFT has an automatic turn off system. If one or more hob zone(s) are left on, the hob zone turns off automatically after a while. In case of a timer assigned to the hob zone, the timer display is turned off then, too. The time limit for automatic turn off depends on the selected temperature level. Maximum operating period is applied for this temperature level. The hob zone may be operated by the user again after it is turned off automatically as described above.

Table-1: Automatic turning off periods

To activate the timer for an operating hob zone on the BEKO HII 64700 UFT:

1. Turn the hob on by touching the On/Off key.
2. Depending on the area you want to turn on, by touching on the setting area or by sliding your finger on the area, set the temperature level you want.
3. Activate the timer by touching the Timer key. The “00” will illuminate and the Timer symbol starts to blink.
4. There are 4 activity LEDs around the “00” displayed on the timer display. For the hob zone to be set a timer, touch the Timer key to select the relevant hob zone side.
5. Set the desired period by touching the Timer increase key or Timer decrease key. You may also advance the timer faster by touching the Timer increase key or Timer decrease key for a long period of time. The Timer symbol illuminates solidly after flashing on the hob zone display for a specific period of time. When the Timer symbol illuminates solidly, this shows that the function is activated.

The timer may only be used for hobs that are being operated. Repeat the procedure above for other hobs that you want to set a timer for. Timer cannot be set without selecting the hob zone and the temperature level of the hob zone. While the timer is active, the time set for the selected hob zone is displayed on the timer display.

To turn off the timers prematurely on the BEKO HII 64700 UFT, if the timer is turned off prematurely, the hob continues to operate with the set temperature until it is turned off. You can turn off by reducing the timer setting to “00” level:

1. Select the timer of the relevant hob by touching the Timer key.
2. Wait until the “00” symbol is displayed on the timer display by touching the Timer decrease key to reduce the value. You may also advance the timer faster by touching the Timer increase key for a long period of time. The Timer symbol flashes for a specific period of time on the hob zone display, then it turns off completely and the timer is cancelled.

To select the high power setting (BOOSTER) directly on the BEKO HII 64700 UFT:

1. Turn the hob on by touching the On/Off key.
2. Touch the Quick Heating key/High power setting (booster) key of the hob you want. The selected hob zone operates with maximum power and 3 lights flash on the hob zone display respectively. When the period for High power setting (See Operating period limits table) has expired, hob will continue operating on the highest temperature level.

To select the high power setting (BOOSTER) while the hob zone is active on the BEKO HII 64700 UFT:

1. Touch the Quick Heating key/High power setting (booster) key when the hob is on and the relevant hob zone is operating at a specific level.
2. The selected hob zone operates with maximum power and 3 lights flash on the hob zone display respectively. When the period for High power setting has expired, hob will continue operating on the highest temperature level.

To turn the high power setting (BOOSTER) off before its expiration on the BEKO HII 64700 UFT, you may turn the high power setting off whenever you desire by touching the Quick Heating key/High power setting (booster) key. The hob zone continues to operate at the highest temperature value. Bring to 0 by touching active hob zone setting area or sliding your finger on the area to turn off.

To clean the glass ceramic surface of the BEKO HII 64700 UFT hob:

• Wait for the product to cool before cleaning the product. Hot surfaces may cause burns!
• Never wash the product by spraying or pouring water on it! There is an electric shock hazard!
• Do not clean the product with steam cleaners as this may cause electric shock.
• Salt, sugar residues on the bottom of the cookware or such particles on the glass surface can cause the glass to scratch and crack. Make sure that the bottom is clean before placing the cookware. Keep the glass ceramic surface clean.
• For cleaning glass surfaces, do not use hard metal scrapers and abrasive cleaning materials. They can damage the glass surface.
• Clean the appliance using dishwashing detergent, warm water and a microfiber cloth specific for glass surfaces and dry it with a dry microfiber cloth.
• If there is residual detergent after cleaning, wipe it with cold water and dry with a clean and dry microfiber cloth. Residual detergent residue may damage the glass surface next time.
• Under no circumstances should the dried-up residue on the glass surface be cleaned off with serrated knives, wire wool or similar scratching tools.
• You can remove the calcium stains (yellow stains) on the glass surface with the commercially available descaling agent, with a descaling agent such as vinegar or lemon juice.
• If the surface is heavily soiled, apply the cleaning agent on the stain with a sponge and wait a long time for it to work properly. Then clean the glass surface with a wet cloth.
• Discolorations and stains on the glass surface are normal and not defects.
• Sugar-based foods such as dark cream, starch and syrup should be cleaned immediately, without waiting for the surface to cool. Otherwise, the glass cooking surface may be permanently damaged.
• Do not use cleaning agents for cleaning operations you perform while the hob is hot, otherwise permanent stains may occur.

If the BEKO HII 64700 UFT product does not operate, check the following:

• The mains fuse is defective or has tripped. Check fuses in the fuse box. If necessary, replace or reset them.
• Product is not plugged into the (grounded) socket. Check the plug connection.
• Buttons/knobs/keys on the control panel do not function. If your product equipped with key lock function, keylock may be enabled. Please disable it.
• If the display does not light up when you switch the hob on again. Disconnect the appliance at the circuit breaker. Wait minimum 20 seconds and then reconnect it.
• Overheat protection is active. Allow your hob to cool down.
• The cooking pot is not suitable. Check your pot.

If the timer is set for any hob zone on the BEKO HII 64700 UFT, the timer resumes to operate during the stop function.