BEHRINGER INUKE NU1000DSP (01) PDF Document

To reduce the risk of electric shock for the BEHRINGER INUKE NU1000DSP, do not remove the top cover or the rear section. Refer servicing to qualified personnel as there are no user-serviceable parts inside.

To reduce the risk of fire or electric shock for the BEHRINGER INUKE NU1000DSP, do not expose this apparatus to rain and moisture. The apparatus shall not be exposed to dripping or splashing liquids and no objects filled with liquids, such as vases, shall be placed on the apparatus.

The basic steps for safe operation of the BEHRINGER INUKE NU1000DSP include:

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

Use only attachments/accessories specified by the manufacturer with the BEHRINGER INUKE NU1000DSP.

Unplug this apparatus during lightning storms or when unused for long periods of time.

Servicing is required when the BEHRINGER INUKE NU1000DSP has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Refer all servicing to qualified service personnel.

The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection.

The POWER button turns the BEHRINGER INUKE NU1000DSP amplifier on and off.

The SIGNAL and LIMIT LEDs display the signal level for each channel. Reduce the input gain if the red LIMIT LED lights up continuously.

The CH A/CH B CONTROLS adjust the input level. To increase signal gain, rotate the knobs clockwise; to reduce the gain, rotate the knobs counter-clockwise.

The PROCESS button steps through the DSP processing modules on the BEHRINGER INUKE NU1000DSP.

The LCD SCREEN displays the current DSP module and parameter settings of the BEHRINGER INUKE NU1000DSP.

The SETUP button steps through parameters within the DSP processing modules on the BEHRINGER INUKE NU1000DSP.

The UP/DOWN/EXIT buttons step through DSP modules and parameters or exit to the top-level iNUKE screen (center button) on the BEHRINGER INUKE NU1000DSP.

The SELECT encoder knob toggles between Graphic and Edit modes (when pressed) and changes parameter values (when rotated) on the BEHRINGER INUKE NU1000DSP.

The USB connection on the BEHRINGER INUKE NU1000DSP enables firmware updates and control over parameters via computer. The USB port is for amplifier configuration only.

Power on the amplifier by pressing the POWER button. The startup screen will appear on the LCD display.

Press the PROCESS button to move by step through DSP screens on the BEHRINGER INUKE NU1000DSP.

Within each screen push the SELECT encoder knob to toggle between Graphic Mode and Edit Mode on the BEHRINGER INUKE NU1000DSP.

In Edit Mode, turn the SELECT encoder knob to change parameters through values and channels. Press the UP/DOWN/EXIT buttons to step through values and channels.

On the I/O (Amp Mode) screen, choose your signal path: BRIDGE, DUAL (Dual Mono), STEREO, BIAMP1 or BIAMP2 on the BEHRINGER INUKE NU1000DSP.

On the PEQ screen, deploy up to 8 different parametric equalizer filters to shape your sound on the BEHRINGER INUKE NU1000DSP.

On the XOVER screen, choose up to 2 cutoff frequency crossover points, and up to 10 different filter curves for each output on the BEHRINGER INUKE NU1000DSP.

On the DEQ screen, you may deploy Dynamic EQ modules (up to 2 per stereo channel) to monitor designated frequency ranges within your signal on the BEHRINGER INUKE NU1000DSP. You may program the Dynamic EQ filters (band-pass, high-pass, or lo-pass) to boost or cut the designated range of frequencies based on your preferred gain threshold, including programmable ratio (Ratio), attack (Atime), and release (Rtime) parameters.

On the DELAY screens, you may compensate for phase cancellation problems in your system by altering signal phase (PHASE: 0° or 180°) and/or delaying the signal output (Delay: 0 to 300 msec) from designated channels to match up with sound traveling over distance (e.g., compensating for sound traveling outward from the stage to sound reinforcement speakers placed out in the audience) on the BEHRINGER INUKE NU1000DSP.

Press the SETUP button to save or load presets, lock the panel and set a password, and control the LCD contrast on the BEHRINGER INUKE NU1000DSP.

To exit to the top-level iNUKE screen, press the EXIT button on the BEHRINGER INUKE NU1000DSP.

The iNUKE DSP automatically stores any recent changes after two minutes or after exiting to the main screen via the EXIT button. These saved changes will be available the next time you power on the unit.

On the Limit screen, you may implement your own threshold (Thresh[old]), release (Rtime), and hold (Hold) settings using the built-in limiters on the BEHRINGER INUKE NU1000DSP.

The steps for Bi-amping the BEHRINGER INUKE NU1000DSP are as follows:

1. Choose the BIAMP1 setting on the Amp Mode screen.

2. Run a 4-pole speaker cable with professional twist-locking connectors from OUTPUTS CH A to the subwoofer. (The subwoofer receives its low-frequency signal from Channel B using poles 2+ and 2-, while the middle and upper frequency ranges use Channel A via poles 1+ and 1-).

3. Set the subwoofer into BIAMPING mode.

4. Run a 2-pole speaker cable with professional twist-locking connectors from the subwoofer to the other speaker.

5. Go to the XOVER screen using the UP/DOWN buttons to set appropriate high/low crossover frequencies.

6. In Channel A#1, choose your high-pass filter type (HPtype: BUT6, BUT12, BES12, etc.) and set the cutoff frequency (HPfreq) to approximately 100 Hz. Deactivate the low-pass filter (LPtype: OFF) on this channel and set the gain level (Gain) to suit your system.

7. In Channel B#1, choose your low-pass filter type (LPtype: BUT6, BUT12, BES12, etc.) and set the cutoff frequency (LPfreq) to approximately 100 Hz. Deactivate the high-pass filter (HPtype: OFF) on this channel and set the gain level (Gain) to suit your system.

The Output Power specifications for the BEHRINGER INUKE NU1000DSP are:

The System Controls specifications for the BEHRINGER INUKE NU1000DSP include:

The following specifications apply to the BEHRINGER INUKE NU1000DSP:

The specifications for the BEHRINGER INUKE NU1000DSP operating with the voltage configuration for Japan are: