Free English AUTEL MAXISYS MS906 PRO2-TS (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD AUTEL MAXISYS MS906 PRO2-TS (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What should I do before operating or maintaining the AUTEL MAXISYS MS906 PRO2-TS unit?
IMPORTANT: Before operating or maintaining this unit, please read these instructions carefully, paying extra attention to the safety warnings and precautions. Failure to use this product properly may cause damage and/or personal injury and will void the product warranty.
How do I connect the MaxiVCI V200 to a vehicle for use with the AUTEL MAXISYS MS906 PRO2-TS?
Step 1. Insert the Vehicle Data Connector on the MaxiVCI V200 into the vehicle’s DLC, which is generally located under the vehicle dashboard.
What are the initial steps for powering up the AUTEL MAXISYS MS906 PRO2-TS tablet after connecting the MaxiVCI V200?
Step 1. Ensure the tablet is sufficiently charged or is connected to the supplied DC power supply.
Step 2. Power up the tablet.
What are the methods to establish a communication link between the AUTEL MAXISYS MS906 PRO2-TS tablet and the MaxiVCI V200?
Method 1: Pair the tablet with the MaxiVCI V200 via Bluetooth to establish a communication link.
Method 2: Alternatively, connect the tablet and the MaxiVCI V200 using the USB cable.
NOTE: The tablet and the MaxiVCI V200 are configured to automatically synchronize with each other on first use, so there should be no need to pair up.
How do I know the AUTEL MAXISYS MS906 PRO2-TS tablet is ready to start vehicle diagnosis after connecting the MaxiVCI V200?
When the MaxiVCI V200 is properly connected to the vehicle and the tablet, the VCI status button on the bottom bar of the screen will display a green badge with a check mark at the corner indicating the tablet is ready to start vehicle diagnosis.
How do I use the AUTEL MAXISYS MS906 PRO2-TS tablet to activate a TPMS sensor?
Hold the MaxiSys MS906 Pro2-TS tablet with its top right corner close to the tire sidewall at the valve stem to activate the TPMS sensor.
What are the components identified on the MaxiSys MS906 Pro2-TS Display Tablet of the AUTEL MAXISYS MS906 PRO2-TS?
1. 8-inch LED Capacitive Touchscreen
2. Ambient Light Sensor detects ambient brightness
3. Power LED
4. Front Camera
5. Microphone
6. TPMS Service Symbol indicates the position of the embedded TPMS antenna
7. Collapsible Stand extends from the back to allow hands-free viewing of the tablet
8. Rear Camera
9. Camera Flash
10. TF Card Slot
11. DC Power Supply Input Port
12. USB Type-C Port supports charging
13. USB Port (for VCI Connection)
14. HDMI Port
15. Headset Jack (3-band 3.5 mm)
16. Power/Lock Button press and hold to turn on/off the tablet, or tap to lock the screen
What are the components identified on the VCI (Vehicle Communication Interface) Device MaxiVCI V200 for the AUTEL MAXISYS MS906 PRO2-TS?
1. Flashlight Power Button
2. Power LED
3. Vehicle/Connection LED
4. Vehicle Data Connector (16-pin)
5. USB Port
What do the Power LED colors indicate for the VCI (Vehicle Communication Interface) Device of the AUTEL MAXISYS MS906 PRO2-TS?
| LED | Color | Description |
|---|---|---|
| Power LED | Yellow | The VCI is powered on and performing self-check. |
| Green | The VCI is ready for use. | |
| Flashing Red | The firmware is updating. |
What do the Vehicle/Connection LED colors indicate for the VCI (Vehicle Communication Interface) Device of the AUTEL MAXISYS MS906 PRO2-TS?
| LED | Color | Description |
|---|---|---|
| Vehicle/Connection LED | Green |
|
| Blue |
|
CLICK HERE TO DOWNLOAD AUTEL MAXISYS MS906 PRO2-TS (01) PDF DOCUMENT