Click here to download AUDIOLAB 6000A (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** SEL 6000A O MODE OUTPUT +0 RIGHT 0+ VOL o audiolab NAME: INTEGRATEO MODEL: 60C.3Ä HUNTINGDON KINGDOM WWWAUDIOLAB.CO.UK WPOATE OUT O CAC220-ucv-50j60Hz FUSE T? A1. -J aooom o 0 IZV TRIG DIGI INPUT User Instructions Audiolab 6000A Manual-IS0622.indd I audiolab INPUT AUXI AUX2 AUX3 audiolab 2018/6/29

****** Page 2 ****** 1: Important Safety Information CAUTION! RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR WARNING: SHOCK HAZARD-DO NOT OPEN This lightning flash with arrowhead symbol within an equi ateral triangle is ‘ntended to alert the user to the presence of non-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. Warning: To reduce the risk of electric shock, do not remove cover (or back) as there are no user serviceable parts inside. Refer servicing to qualified personne . The exclamation point within an equilateral triangle is intended to alert the user to the presence Of important operating and maintenance instructions in the literature accompanying the appliance IMPORTANT SAFETY INFORMATION Read these instructions. Keep these instructions. Heed al warnings. FoI ow all instructions. Do not use this apparatus near water. Clean on y with dry c 0th. Do not b ock any ventilation open’ngs. Install in accordance with the manufactureffs instructions. Do not instal near any heat sources such as radiators, heat reg’sters, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the po arized or grounding type plug. A po arized plug has two blades with Audiolab 6000A Manual-IS0622.indd 2 one wider than the other. A grounding plug has two blades and a third ground’ng prong. The wide blade or the third prong is provided for your safety. f the provided plug does not fit into your outlet, consult an electrician for rep acement of the obsolete outlet. Protect the power cord from being wa ked on or pinched particular y at the plugs, convenience receptacles, and at the point where they exit from the apparatus. Use on y with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart or rack is used, use caution when moving the cart/ apparatus combination to avoid injury from tip over. Unp ug this apparatus during lightning storms or when unused for ong periods of time. Refer al servicing to qualified service personne . Servicing is required when the apparatus has been damaged in any way, such as power supp y cord or p ug is damaged, liquid has been spil ed or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normal y, or has been dropped. CAUTION: These servicing instructions are for use by qualified service personnel on y. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions un ess you are qualified to do so. Do not install this equipment in a confined or built in space such as a bookcase or similar unit, and keep we ventilated in open space. The ventilation shou d not be impeded by covering the ventilation openings w’th items such as newspaper, table c oths, curtains etc. WARNING: On y use attachments/accessories specified or provided by the manufacturer (such as the exclusive supp y adapter, battery etc). Page 1 WARNING: Please refer to the information on the exterior panel of the enclosure for electrical and safety information before installing or operating the apparatus. WARNING: The battery (battery or batteries or battery pack) shal not be exposed to excessive heat such as sunshine, fire or the like. CAUTION: Danger of explosion if battery is incorrectly rep aced, Replace on y with the same or equiva ent type. WARNING: For the terminals marked with symbol of may be of sufficient magnitude to constitute a risk of electric shock. The external wiring connected to the terminals requires installation by an instructed person or the used of ready made leads or cords. Mains Supply: The mains operating voltage of Audiolab 6000 series units is shown on the rear pane f this vo tage does not match the mains vo tage in your area, consu t your Audiolab dealer about converting the unit. The mains supp y fuse on the rear panel is accessible when the EC mains plug has been removed. In the rare event that it has broken, check for any obvious cause before rep acing the fuse with one of the correct rating and type. The fuse values are: 220 – 240/ (I-JK, china, etc.) T2.OAL 250V Slow Blow 100 (USA, Japan, etc.) T40AL 250V Slow Blow 2018/6/29

****** Page 3 ****** 2: Getting Started Welcome to Audiolab 6000 Series. 6000A is the latest in a ong line of Audiolab integrated ampl fiers wth a pedigree that stretches back to the very first 8000A that made Audiolab an overnight sensation. The 6000A features ana ogue and digital audio circuitry of the highest quality and has been designed by engineers who are passionate about the reproduction of music, and we hope you wil enjoy its performance for many years to come. Please read through this manual to obtain the very best performance from your 6000A Features: Bluetooth aptX DAC ES9018K2M Dedicated high performance MM Phono nput. Separate Pre Power sections for flexibility of operation. Automatic equipment activation via 1 21/ trigger. Auto standby function. Inputs: Three ana ogue line leve One Phono input (MM) One Power-Amp input Two Coaxial SPD F digita Two optical SPDIF digita Bluetooth (aptX) Audiolab 6000A Manual-IS0622.indd 3 inputs. inputs inputs Page 2 Outputs: Pre-Amplifier output. Loudspeaker output. Headphone output, Unpacking Unpack the product ful y. The carton shou d contain: The Audiolab 6000A One EC power cord suitable for your area. One Remote handset with two AAA batteries This instruction manua . One Bluetooth Antenna f an item is missing or damaged report this to your dealer as soon as possible. Retain the packing for safe transport of your unit. f you dispose of the packing, do so with regard to any recycling regulation in your area, Placement The unit is designed to run warm during normal operation but ensure you do not block any ventilation openings. Place the unit on a sturdy she f or table. If you use an equipment rack, ensure the unit has adequate venti ation and is on its own she f. Check your mains vo tage corresponds to the rating printed on the rear panel (near the power inlet socket). f n doubt, consu t your dealer. f you move to an area with a different mains vo tage seek advice from an Audio ab appointed dealer or a competent service technician. 2018/6/29

****** Page 4 ****** 3: Controls and Connectors SEC 6000A vot- VOLUME audiolab HIUNTINGOON,UNITEO U POATE UPDATE O HEADPHONE SOCKET POWER LED OFF O SET* *sav -i o SOURCE SELECTOR OUTPUT +0 o IOUDSPEAKER OUTPUT MODE 0+ o DISPLAY O aul REMOTE NPLT audiolab GROUND STANDBY BUTTON MAINS NPCIT ROWER SWITCH ‘NPUT I pv TRGGERS BLUETOOTH OPT/DIG ANTENNA NPUT Page 3 FAE PRE OUTPUT AUX3 ANALOGUE NPUTS Audiolab 6000A Manual-IS0622.indd 4 2018/6/29

****** Page 5 ****** 4: Remote Handset NOTE : the handset buttons shown crossed out are for use with other Audio/ab units like Audio/ab 6000CDT and are not operational when used with the 6000A O MUTE AEF’EAT STORE MENU VOL+ VOL— 1 STANDBY 2 VOL+ 3 VOL 6 CD 7 SOURCE 8 MODE 9 MUTE 10 MENU 11 12 13 11 O Audiolab 6000A Manual-IS0622.indd 5 INFO OISPLAY oev•ce audiolab Press to bring the unit in/out of Standby ncrease Decrease Volume Press to toggle the disp ay on/off Press to select 6000A remote mode Press to select 6000CDT remote mode Press to cyc e source inputs Press to select 6000A operating mode Press to mute and unmute the sound Press to enter MENU Press once to replay the current track of BT Move to previous page or setting “n menu Press to start / pause BT p ayback Press to confirm page or setting se ected in menu Move to the next track of BT Move to next page or setting in menu Page 4 Fitting Batteries Open the battery compartment cover, unwrap the supplied AAA batteries and p ace them in the battery compartment with the correct po arity. Rep ace the cover. A ways use AAA batteries and rep ace them in sets never mix o d and new batteries. Very weak batteries can leak and damage the handset. Replace them in good time! Note: there is a risk of fire and burns if a battery is handled improper y. Do not disassemble, crush, puncture, short the contacts or dispose of the batteries in fire or water. Do not attempt to open or service a battery. Discard used batteries in ful accordance with recycling regu ations in force in your area. Handset Operation The handset operates several Audiolab components. The handset buttons shown crossed out are for use with other Audiolab units and are not operational when used with the 6000A. Point the handset at the remote receiver and press the relevant key. The handset should be within 15 meters of the p ayer and there must be a clear line of sight between the two units. 2018/6/29

****** Page 6 ****** 5: Connections Analogue Inputs (Line Level) Connect your analogue sources to one of the three line eve inputs, AUXI, AUX2 or AUX3. Phono Input (MM) Connect your Turntab e (Moving Magnet cartridge) to the PHONO nput. Connect the Earth ead from your Turntab e (if avai ab e) to 000 O PHONO— ALIX I O the GROUND termina Coaxial digital Inputs Connect your coaxial digital sources to either DIGI Optical digital Inputs Connect your Optical d g tal sources to either OPTI Pre-Amplifier Output AUX2 DIGITAL or DIG2. J AUX3 Page 5 Once paired the front panel SOURCE indicator will be turned on, If you switch to another input on the 6000A your mobile device will be disconnected after 60 sec. To reconnect, select BT on the 6000A and it will connect to the last paired device, or se ect ‘Audiolab 6000A BT’ on your mobile device in the Bluetooth menu and it wil reconnect. 12V Trigger Connections The 6000A features two 12V Trigger connections, one output and one input. Use the output to control other products (ie. Audiolab amplifiers or 3rd party compatible equipment). Use the input when the 6000A is to be control ed (ie. by Audiolab 6000CDT, or 3rd party compatib e equipment). The Trigger connections are made using 3.5mm to 3.5mm jack interconnects (not ncl OPTI 01G1 DIG2 INPUT OUT o audiolab Pre-amplifler output for driving external power amplifiers, sub woofers or signal processors. Loudspeaker Terminals One set of Loudspeaker output terminals. Headphone Output A stereo 6.3mm (1/4′) jack is provided on the front panel for connecting Headphones. When Headphones are connected the audio to the oudspeakers termina swi be cut off. Bluetooth Connection Select BT source on the 6000A, on your mobi e device search for ‘Audiolab 6000A BT’ and connect. Audiolab 6000A Manual-IS0622.indd 6 audiolab o o_ Mains Input Before connecting the 6000A to the mains supply make sure all other connections to your system have been proper y and securely made. Make sure the ON/OFF switch on the rear of the unit is switched off Now connect the supplied mains cable to the AC supply outlet. O O tAC220-240V-S0i’60Hz 440nn FUSE 12 SAL 250V 2018/6/29

****** Page 7 ****** 6: Operation Switching On and Off Mute Switch on all source units before switching on power to the 6000A. Press the VOL knob on the front panel or the MU E button on the remote handset to mute / un-mute the sound. When switching On: The power LED il uminates. When switching Off Switch off the 6000A before the source units. Display Setting The DISPLAY button on the remote control wil togg e the front panel disp ay ON/OFF. Standby Mode When the disp ay is OFF: Using the front panel contro s or pressing any remote key will The 6000A will enter standby mode after being powered on. Press momentari y turn on the disp ay, after 5 sec. the disp ay will go off. the “StandbV’ button to bring the 6000A out of standby, the power indicator LED becomes brighter and the disp ay shows “6000A” welcome screen while the unit is getting ready for operation. Digital Filter selection (DAC) The Auto Standby feature will, by defau t, put the unit into standby The DAC in the 6000A has a choice of 3 digital filters. Press the MENU key on the after 20min of inactivity. remote control to access the FILTER options (see page 8 for further detai s) This feature can be configured using the MENU (see page 8) and be set to 20min, 1 hour or Never. Filter = Fast SEL Source Select Rotate the SEL knob on the front panel or use the source buttons on the remote handset to select different source inputs. Volume Control VOL Rotate the VOL knob on the front panel, or use the Volume up/down keys on the remote control, to set the vo ume level. The range is 78dB to +8dBf the factory defau t vo ume setting is -20dB. When coming out of standby the 6000A will be set to the previous used volume setting, except if ouder than -20dB, in which case the volume will default to -20dB. Audiolab 6000A Manual-IS0622.indd 7 Filter — Slow: Filter — _ Phase: Page 6 Standard flat response with fast frequency roll off above Fs/2 (ha f the sampling frequency) Starts rolling off at a lower frequency than the Fast filter but has a more gent e rate of attenuation. Has a gentle attenuation slope similar to the Slow fi ter but with minimum phase characteristics. It can be likened to an ana ogue filter applied in the digital domain. 2018/6/29

****** Page 8 ****** 6: Operation – 2 Operating Modes A though the 6000A is an integrated amplifier it can function as a separate Pre and Power amplifier. Use the MODE knob on the front panel, or the MODE key on the Remote control, to select different operating modes. MODE PRE POWER NTEGRATED POWER AMP DISAB E ACT VE DISABLE N PRE OUT ACTIVE ACT VE ACTIVE HEADPHONE OUT ACTIVE ACT VE ACTIVE MODE LOUDSPEAKERS DISAB E ACT VE ACTIVE Integrated mode The pre-amplifier section is Interna y connected to the power amplifier, Pre-amplifier output is also operational in this mode. A second power amplifier can be connected for bi-amplificatlon as shown in the diagram O 1 FUSE n Audiolab 6000A Manual-IS0622.indd S +0 o O OUT Page 7 Pre-Power mode The pre-amplifier section is internal y d’sconnected from the power amplifier. The 6000A can be used as a stand alone power amplifier (ie. part of an AV setup). This mode can a so be used if additional signal processing is required, connecting the Pre out to an external signal processor and then take the output from the processor to the 6000A Power IN. POWER aud101ab Pre Mode All signa s to and from the power amplifier of the 6000A are disconnected. n this mode, the 6000A functions as a stand-alone pre-amplifier. The pre amplifier section of the 6000A can be connected to a stereo power amplifier, or to two mono b ock amplifiers. audiolab HUNT “NGOC” -L Output to the External power amplifier 2018/6/29

****** Page 9 ****** 6: Operation – 3 The MENU The menu enables you to customize the unit and optimize the interface with other equipment in your system. 6000A has 6 different menu pages. Press the MENU key on the remote control to enter menu mode, and then press or to turn to different menu pages, press to enter any again to select different settings, Pressing the MODE knob on the front panel can also enter the menu mode, rotating this knob turns through the menu menu page, press or »l pages; press the MODE knob again to enter any menu page and rotate the knob to change the setting press the MODE knob again to select a setting. No operation for 5 seconds will also exit menu mode automatical y The Menu Tree BALANCE Audiolab 6000A Manual-IS0622.indd 9 FILTER FAST SLOW PHASE TRIGGER ENABLE DISABLE Page 8 STANDBY 20 MIN I HOUR NEVER RESET NO YES VER-OI 6 2018/6/29

****** Page 10 ****** 7: VVarranty Audio ab Ltd. warrants this product, subject to the terms and conditions be ow, to be free from defects in materia s and workmanship. During the warranty period Audiolab will repair or rep ace (at Audio ab’s option) this product, or any defective part ‘n th s product, if it is found to be defective due to fau ty materials, workmanship or function. The warranty period may vary from country to country. Terms and conditions The warranty starts on the date of purchase (or the date of delivery if this is ater). You must provide proof of purchase/delivery before work can be carried out. Without thIS proof, any work carried out will be chargeab e to you. A1 work will be carried out by Audiolab or its authorized agents or distributors. Any unauthorized repair or modification wi void this warranty. f any part is no onger available it will replaced with a functional rep acement part. Any parts that are replaced will become the property of Audiolab. Any repair or rep acement under this warranty will not extend the period of warranty. ThlS warranty is valid on y in the county of purchase, applies on y to the first purchaser and is not transferab e. The following are not covered: 1. Products where the serial number has been removed, altered or otherwise made il egib e. 2. Normal wear tear and cosmetic damage. 3. Transportation or installation of the product. Accidental damage, fau t caused by commercial use, acts of Godf incorrect installation, connection or packing, misuse, neg ect or careless operation or handl ng of the product which is not in accordance With Audiolab’s user instructions. 1. Repairs or alterations carried out by parties other than Audio ab or Its authorized agents or distributors. 2. Products not purchased from an Audio ab authorized dea er. Page 9 Audiolab 6000A Manual-IS0622.indd 10 3. Products that were not new at the time of original purchase. 4. Products so d ‘as is’, *as seen’ or ‘with all faults’. Repairs or rep acements as provided under this warranty are the exclusive remedy of the consumer. Audiolab shall not be liab e for any incidental or consequential damages for breach of any express or implied warranty in this product, Except to the extent prohibited by avv, this warranty is exclusive and in lieu of al other warranties whatsoever, both express and mpliede including, but not limited to, the warranty of merchantability and fitness for a practical purpose. This warranty provides benefits that are additional to and do not affect your statutory rights as a consumer. Some countries and U.S. states do not allow the exclusion or limitation of incldental or consequential damages or implied warranties so the exclusions in the paragraph above may not appy to you. ThlS warranty gives you speciflc legal rights, and you may have other statutory rights, which vary from state to state or county to county. How to claim: To obtain warranty service contact the Audiolab authorized dealer from which you purchased this product. Do not dispatch goods without the prior agreement of the dealer, Audiolab or their authorized distributors. f asked to return products for inspection and/or repair, pack careful y, preferaby in the origina cartons or packing affording an equal degree of protection, and return prepaid. f unsuitab e packaging is used, Audiolab may make a charge for the supp y of new packaging. nsurance is recommended and goods are returned at owner’s risk. Audio ab or their authorized distributors cannot be he d liable for oss or damage in transit. 2018/6/29

****** Page 11 ****** B: Specification Pre-amplifier Section Gain (max.) nput Sensitivity nput mpedance Total Harmonic Distortion (THD) Frequency Response Output Voltage Output mpedance Signal-to Noise Ration (S/N) DAC D to A converter Total Harmonic Distortion (THD) Output evel (OdBFSf KHz) Max. Sampl ng Frequency Signal-to-noise ratio (SIN) Digital Filters Power Amplifier Section Gain Rated Max. Power Output Frequency Response nput Sensitivity Total Harmonic Distortion ( Signal-to Noise ratio (SIN) Max. Output Current Audiolab 6000A Manual-IS0622.indd I I +8dB (Line) +55dB (Phono MM) 720mV (Line, Volume = OdB) 3.1 mV (Phono MM/ Volume=0dB) 0K (Line) (Phono MM) 1 1 OdB (Line, A-weighted) >76dB (Phono MMt A weighted) ES9018K2M 1 1 2dB (A-weighted) OdB) Headphone Amplifier Total Harmonic Distortion (THD) Output mpedance Load impedance General Standby Power Consumption Power Requirements Dimensions (mm) (W x H x D) Carton Size (mm) (W x H x D) Weight < 0.01% (1k z, 50mW) 2.35 ohm 20-600 ohm <O.5W 240V 50 230V — 1 oov – 50 50 115V – 50 – 60Hz 445 x 655 x 300 512 x 467 x 146 7.8kg (Net) 60Hz 60Hz 60Hz Fast Roll-off , S ow Rol -off f Minimum Phase +29dB 2 X (8 ohm, THD<1 0/0) 2 X 75W (4 ohm, THD 1 1 OdB (A-weighted) Correct disposal of th’s product. This marking indicates that this product should not be disposed with other household wastes throughou he EU. To prevent possible harm to the environment or human hea th from uncontrolled waste disposal, recyc e it responsib y to promote the sustainable reuse of material resources. To return your used device, p ease use the return and col ection systems or contact the retai er where the product was purchased, They can take this product for environmental safe recycling. Page 10 2018/6/29

****** Page 12 ****** Audiolab IAG House, a/ q 4 Glebe Road, Huntingdon, Cambridgeshire, PE29 7DL, Tel: +4410) 1 480 452561 Fax: +4401 480 41 3403 http ://audialab.ca.uk CODE: AHI 4-MNL0004a Audiolab 6000A Manual-IS0622.indd 12 2018/6/29

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL



AUDIOLAB 6000A (01) PDF MANUAL

Leave a comment, question, review or page error below.

This site uses Akismet to reduce spam. Learn how your comment data is processed.