Click here to download AUBE TI033 (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** technologies O Applications The T 1033 programmable wall switch has been designed to control lightings and motors: Load type Maximum load Examples T1033 Installation and User Guide Programmable Wall Switch O Setting the Clock NOTE: The switch displays the time in 24-hour format by default or following a reset. 2400 w Resistive load (20 A @ 120 V) 2400 w Inductive load Motor (20 A @ 120 V) 1 hp Installation incandescent lights halogen lights block heater fluorescent lights compact fluorescent lights (CFL) sodium lamps electronic ballasts pool filter pumps fans O O O To change to 12-hour format (or vice versa), proceed as follows: a) Press one of the control buttons to ensure the MAN or AUTO indicator is displayed. b) Press the MIN and HOUR buttons simultaneously and brief- tly (0:00 display = 24-hour, 12:00 display = 12-hour ). Set the time using the HOUR and MIN buttons. If you have selected the 12-hour format, ensure that PM appears on the screen when an afternoon time is displayed. Set the day by using the DAY button. Press one of the control buttons or close the switch door to return to normal operation. NOTE: This switch cannot be used if there are not at least 2 white wires joined by a connector inside the electrical box. O Cut power at the circuit breaker to avoid electric shock. @ Remove the existing switch. O Install the new switch as shown in the diagram below. O Selecting the Operating Mode The programmable switch has 2 operating modes: manual (MAN) and automatic (AUTO). To switch mode, press the switch door for 3 O Apply power at the circuit breaker. black white white (neutral) 120 VAC black (line) O Power-On O Pry the switch door open from the bottom using a small screwdriver. @ Ensure the ONIOFF selector is set to ON. O Reset the switch using a paper clip. 0:00 and MO will flash. If the display is blank. seconds. Manual Mode The programmable switch operates as a regular switch. Briefly press the switch door to turn the lights On or Off. The mode (MAN) and state (ON or OFF) are displayed Automatic Mode The programmable switch follows the programmed schedule. The mode (AUTO), state (ON or OFF) and current program number are displayed. To temporarily override the programmed schedule, MAN blue black white T.oo Haug AUTO OFF briefly press the switch door. The new state (ON or OFF) will flash to show that this state is temporary. The override remains in effect until you press the switch door again or until the beginning of the next program. Programming You can set up to 7 programs. To set a program, you need to enter its start time (ON) and its end time (OFF). O Reset Control (4) On/Off selector Ensure the ONIOFF selector is properly engaged in the ON posi- tion. Push it to the right using a small screwdriver. T1033 Pry the switch door open using a small screwdriver. Press the PGM button to display a program and its On or Off time. For example, when you first press PGM, program number 1 (Pl) and its On time (ON) will appear. – : – – will appear instead of the time if the program is not set (inactive). Press the DAY button to select the day to which you want to apply the program. NOTE: If you want to apply the program to every day of the week, press DAY until all the MOTIJWETH FR SA SU days are displayed. (This still counts as 1 program, not 7) 400-033-001-c 30/11/06 1/2

****** Page 2 ****** To set another program, repeat steps 2 through 6. Programs that are not set will remain inactive. Press one of the control buttons or close the switch door to return to normal operation. Clearing a Program Press the PGM button until the desired program is selected. Hold the erased Troubleshooting O Press the HOUR and MIN buttons to set the ON time (time when you want the lights to turn on). If you have selected the 12-hour format, ensure that PM appears on the screen when an afternoon time is displayed. O After you have programmed the ON time, press the PGM button to display the OFF time (time when you want the lights to turn O O O PGM button for 3 seconds. – : appears when the program is off). Repeat steps 3 through 5 to program the OFF time. If the program ON time is set for every day of the week, the program OFF time will automatically be set for every day. OFF Blank display Faded or irregular display Cannot switch bewveen 24-hour format and 12-hour format Programs do not run as expected The switch resets itself without apparent rea- son when used to con- trol an inductive load such as a relay or a contacton • Verify circuit breaker at main panel. • Ensure the ONIOFF selector is at ON • Reset the switch using a paper clip. Ambient temperature below freezing point First, press one of the control buttons so that MAN or AUTO appears on display. • Make sure the switch is properly pro- grammed. • Note that – : – – indicates an inactive pro- gram, 00:00 indicates midnight. • If the switch has been configured for 12-hour format, check that PM appears on the left side of the screen when an afternoon time is displayed. The reset is caused by the load. Install a snubber (AC130-03) at each relay/con- tactor. Warranty AUBE warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and ser- vice, for a period of three (3) years from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, AUBE shall repair or replace it (at AUBE’s option). If the product is defective, return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it, or (ii) contact AUBE. AUBE will make the determination whether the product should be returned, or whether a replacement product can be sent to you. This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by AUBE that the defect or mal- function was caused by damage which occurred while the product was in the possession of a consumer. AUBE’s sole responsibility shall be to repair or replace the product within the terms stated above. AUBE SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCI- DENTAL OR CONSEQUENTIAL DAMAGES RESULTING DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WAR- RANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some provinces, states or regions do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you. THIS WARRANTY IS THE ONLY EXPRESS WARRANTY AUBE MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANT- ABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE THREE-YEAR DURATION OF THIS WARRANTY. Some provinces, states or regions do not allow limita- tions on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from one province, state or region to another. Customer Assistance If you have any questions on the product installation or operation, contact us at: 705 Montrichard Avenue Saint-Jean-sur-Richelieu, Quebec J2X 51<8 Canada Tel.: (450) 358-4600 Toll-free: 1-800-831-AUBE Fax: (450) 358-4650 Email: aube.service@honeywell.com For more information on our products, go to aubetech.com Supply: 120 VAC, 50 / 60 Hz Maximum load: 2400 watts resistive or inductive, 1 HP motor Operating temperature range: 50F to 1220F (-150C to 500C) Storage temperature range: -40F to 1220F (-200C to 500C) Power outage: The programs are protected by a rechargeable battery. The screen is blank during the power outage. Certifications: CSA & UL T1033 400-033-001 c 30/11/06

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL



AUBE TI033 (01) PDF MANUAL

Leave a comment, question, review or page error below.

This site uses Akismet to reduce spam. Learn how your comment data is processed.