Click here to download AUBE TH106 (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** aebe technologies MODEL TH106 SUMMARY • OPTIONS SELECTION Inside the thermostat, there are 4 selection switches to set at your pre- ferences. Cycles of 15 minutes or 20 seconds, temperature in oc or OF, time in 12 or 24 hours and Early Start function. • TO SET TIME AND DAY Press on DAY, HOUR and MIN buttons to adjust time and day. • TO RECORD THE -k (COMFORT) SETPOINT TEMPERATURE Select chosen setpoint temperature by using the A or v button. Press on -XX- button (2 to 3 seconds) until -k icon appears on display. • TO RECORD THE ( (ECONOMY) SETPOINT TEMPERATURE Select chosen setpoint temperature by using the A or v button. Press on ( button (2 to 3 seconds) until icon appears on display. • TO RECORD THE • (VACATION) SETPOINT TEMPERATURE Select chosen setpoint temperature by using the A or button. Press on -V: and buttons simultaneously (2 to 3 seconds) until • icon appears on display. • OPERATING MODES Use MODE button to select an operating mode or to exit the programming. INSTALLATION NOTE : The “Problems and Solutions” section located at the end of this docu- ment will help you to correct the problems you might have during the installation. This thermostat has been designed to operate with any installation which has a RESISTIVE load not exceeding 4000 W (16.7 A) @ 240 VAC or 2000 W @ 120 VAC as electric baseboards, radiant ceilings and floors, electric convectors, etc. It is not compatible with a low voltage controller used by a central heating sys- tem or systems using a contactor or a relay whose current is under 1.0 A. Electricians or experienced technicians should install the thermostat. This ther- mostat is designed to be used with a self-protected heating system equipped with linear limit control and circuit breaker. PARTS INCLUDED : • One (1) THI 06 thermostat • Two (2) 6-32 screws • Two (2) solderless connectors TURN OFF POWER OF THE HEATING SYSTEM AT THE MAIN POWER PANEL TO AVOID ELECTRIC SHOCK. Keep air vents of thermostat clean and free from obstructions. CONNECTING WIRES AND MOUNTING THERMOSTAT AUTO : MAN Runs the program. A or V shows temperature setting and can override temporarily your programming up to the next program. Maintains the selected temperature. A or changes the temperature setting. ill”‘ Remove the screw holding the base and the front part of the thermostat. Lift the front part of the thermostat to separate it from the base. Make the appropriate connections. Please note that the thermostat wires are not polarized, therefore the connections can be made on either terminal. 2 wire installation Comfort setting Economy setting 4 wire installation 120 / 240 V ca To set the day To set the time To set the programming To erase a program Selection of the operating mode and exit for the programming function Operating modes Day Hour Min Heating indicator “TUWETHFRSASU a be oo Hour and day of the week Ambient or setting temperature Comfort, Economy or Vacation settings Program number 120/ 240 To adjust the temperature setting Align and afix the base to the electrical box. 920-106-001-OO-I-B 1/4

****** Page 2 ****** 15 E.S. On 20 sec. Off iäh Set the 4 switches located at the back of the thermostat to your preferences. 1: Cycles of 15 min. (fan) or 20 sec. 2: Early Start 3: Time display in 12 or 24 hours 4: Temperature display in oc or OF AUTOmatic ( O ) This mode executes your own programming. icon. The or To activate this mode, press on Mode button to display the icon indicates which temperature setting is used. TELEPHONE CONTROLLER The THI 06 incorporates a telephone controller interface which allows you to switch from the normal operating mode to the Vacation setting ( and vice versa, using the telephone keypad (stationary or portable). You can, for exam- ple, heat your country house from your office on Friday, or your house from the airport or from your car on your way back from vacation. When the telephone controller sends a signal, the icon appears on the screen. Connection to the CT240 The THI 06 is designed to connect directly to the CT 240 telephone controller. This combination allows the activation and deactivation of the Vacation mode from the CT240 or the telephone. NOTE 1: This thermostat has been factory set to proportionally control electric baseboards, radiant systems and convectors. Since proportional control uses a fast commutation rate, it is not compatible with fan equipped systems (see characteristics). Also, this control mode could occasionally create light flickering, especially in rural area. By switching to the 15 minute cycle mode, the thermostat will be compati- ble with fan equipped systems. NOTE 2: The thermostat is providing a built-in function enabling it to calculate the optimum time to start the heating system to achieve the desired tempera- ture setting at the programmed time. To enable this function, set the switch E.S. to “ON” at the back of the thermostat. Replace the front part of the thermostat on the base and secure them in place with the screw. NOTE : All cables and connections must conform to the local electrical code. WARNING : Special CO/ALR solderless connectors must be used when con- necting with aluminium conductors. 06 o CT240 c x c 0 Power-up 0:00 68 4 When power is applied for the first time, the dis- play must show the time 0:00, the ambient tem- perature and the Manual mode icon ( ). Other Information might show up on the display if Installation is defective or does not comply with the instructions. 500 watts or less installation During the 30 minute period following the instal- lation or a long power failure (more than 2 hours), the light intensity of the display decreases when a button is pressed on while the thermostat is in the heat mode. This problem will disappear when the accumulator for the memory backup will be charged. OPERATING MODES The THI 06 has two (2) operating modes : MANual ( This mode allows you to maintain a constant ambient temperature. I- To activate this mode, press on Mode button to display the icon. 2- Set the desired temperature using the A v buttons or select the pre- programmed -k , (C or settings. (To select the • setting, press on -k- and (simultaneously.) Connect the CT 240ts terminals A and C to the TH106’s terminals X and C respectively. You must respect the polarity. The signal given by the CT240 is a low voltage signal and must not circulate in the electrical box. The wire must run on the exterior side of the electrical box to join the thermostat. Use a 18 to 22 gauge flexible wire and pass it behind the thermostat through the slot located in front of the connector. For details on operating the telephone controller, refer to the CT240is Instruction Manual. PROGRAMMING Programming the time and day I- Set the time using the Hour and Min buttons. 2- Set the day using the Day button. Programming the Comfort, Economy and Vacation settings The Comfort -k , Economy( and Vacation settings respectively represent the temperatures that you wish to have during the day * , at night or while you are away at work ( , or while you are away for an extended period • To program your settings a) To program the Comfort temperature, select the desired degree using the A V buttons and press the -k button until the icon is displayed (app. 3 seconds). b) To program the Economy temperature, select the desired degree using the A buttons and press the button until the icon is diplayed (app. 3 seconds). c) To program the Vacation temperature, select the desired degree using the A V buttons and press on the -k and ( buttons simultaneously until the icon is displayed (app. 3 seconds). d) Press the Mode button to exit this function and return to the normal operating mode. Schedule programming The THI 06 allows 4 setting changes for each day of the week. There are no pre-set programs. The programs are tailored to perfectly adapt to your life style. The principle is very simple. For each day, enter the time at which you awake (Pl), the time you leave for work (P2), the time you arrive back home (P3) and the time you go to bed (P4). 920-106-001-OO-I-B 2/4

****** Page 3 ****** pro ram Mode Comfort Economy Comfort Economy Time Wake-up time Leaving time Return time Bed time For savings to be obtained, you must lower the temperature for a period of 2 to 3 times the delay required to bring the temperature back to your comfort level. Example : If your system takes one hour to go from your saving temperature level to your comfort temperature level, it is useless to lower the temperature for a period less than 2 to 3 hours. a) To Program your schedule : 1- Press on PGM button to access the programming mode. 2- Press on Day button to select the day to be programmed. You can select all days of the week by pressing on Day button for 3 seconds. 3- Press on PGM button to select program 1, 2, 3 or 4. 4- Press on Hour and Min buttons to program the time. 5- When you have completed your programming, press on Mode button to exit this function. b) To Erase a Program : Select the program using PGM and Day buttons, and press on Clear button. The time field displays –:– when the program is inactive. c) Example 1 Comfort period from 7:00 AM to 10:30 PM Economy period from 10:30 PM to 7:00 AM Identical schedule for all days of the week. To modify the Saturday and Sunday schedules 6- Press on Day button until SA or SU is displayed. 7- Press on PGM button to select Prog. 1 and Hour and Min buttons to enter 7:30 AM. 8- Press on PGM button to select Prog. 2 ( ( ) and then Clear button to erase it. 9- Press on PGM button to select Prog. 3 ( •k- ) and then Clear button to erase it. 10- Press on PGM button to select Prog. 4 ( ) and then Hour and Min buttons to enter 11 PM. 11- Press on Mode button to exit this function. TEMPORARY OR PERMANENT TEMPERATURE BYPASS This operation allows you to temporarily modify the temperature while you are in the Automatic mode. Simply press on A or button to select the desired temperature, or the -k or ( button to select the Comfort or Econo setting you have programmed. This temperature will be maintained until the beginning of the next program. You can also switch to the Vacation setting for a prolonged absenæ by pressing on -k and buttons at the same time. The display will show icon. In that case, the temperature bypass is permanent. To return to the normal operating mode, press on Mode button. If you wish to return immediately to the programmed settings, press on Mode button twice. MEMORY BACKUP In the event of a power failuret an internal circuit will maintain the programming. Only the time will have to be set if the power failure is more than two hours. The thermostat will return to the same operating mode as set before the power failure. Schedule/Day PROG. 1 PROG 2 PROG. 3 PROG 4 MON. 7:00 AM 10:30 PM TUES. 7:00 AM 10:30 PM WED. 7:00 AM I OOO PM THU. 7:00 AM 10:30 PM FRI, 7:00 AM SAT. 7:00 AM 10:30 PM 10:30 PM SUN. 7:00 AM 10:30 PM CHARACTERISTICS This thermostat works differently than the con- ventional electromechanic one. The latter can have a differential of temperature up to 4 oc (7.2 OF) while this electronic thermostat has one of only 0.2 oc (0.36 OF). This slight oscillation eliminates the discomfort often found with con- ventional electromechanic thermostats. The proportional controller determines the amount of power required by the electric heating system to maintain the exact ambient tempera- ture of the temperature setting. To see this process, the display showst in real time, the percentage of power applied to the electric heating system. 100% 80% 20% MO 1- Press on PGM button to access the programming mode. 2- Press on Day button 3 seconds to select every day of the week. 3- Press on Hour button to enter 7:00 AM, Prog. I ( ). 4- Press 3 times on PGM button to select Prog. 4 (C ), and press on Hour and Min buttons to enter 10:30 PM. 5- Press on Mode button to exit this function. d) Example 2 : Comfort period Monday to Friday from 6:15 AM to 8:15 AM and from 5:00 PM to 10:00 PM. Saturday and Sunday from 7:30 AM to 11:00 PM Schedule/Day PROG 1 PROG 2 PROG 3 PROG 4 NOTE : MON. 6:15AM 8:15AM 5:00 PM 10:00 PM TUES. 6:15 PM 8:15 PM 5:00 PM 10:00 PM WED. 6:15AM 8:15AM 500 PM 10:00 PM THU. 6.15AM 8.15AM 5:00 PM 10:00 PM FRI. SAT. 6:15AM 780 AM 8:15AM 5:00 PM 10:00 PM 11:00 PM SUN. 7130 AM 11 PM It is faster to program the same schedule for every day and then modify the exception days. I- Press on PGM button to access the programming mode. 2- Press on Day button 3 seconds to select every day of the week. 3- Press on Hour and Min buttons to enter 6:15 AM Prog. 1, ( -k) 4- Press on PGM button to select Prog. 2 ( ( ) and Hour and Min buttons to enter 8:15 AM. 5- Repeat step 4 to enter Prog. 3 (5:00 PM) and Prog. 4 (10:00 PM). NOTE : When making modifications, make sure you are in the right program. – Model : – Supply : – Load – power : – Minimal load – Approval – Display range – Setting range – Storage : Default setting : Default setting : – • Default setting : clJLus TH106 120/240 VAC, 50/60 Hz 16.7 A max. (resistive only) 1.0 A min. 4000 W @ 240 VAC 2000 W @ 120 VAC 240 W @ 240 VAC 120 W @ 120 VAC O to 60 oc (32 to 140 OF) 5 to 30 oc (40 to 85 OF) -20 to 50 oc (-4 to 120 OF) 20 OC (68 OF) 18 OC (64 OF) 10 OC (50 OF) 920-106-001-OO-I-B 3/4

****** Page 4 ****** WARRANTY AUBE TECHNOLOGIES INC. ONE (1) YEAR LIMITED WARRANTY This product is warranted against material defects and workmanship in normal use for a period of one year, from the date of the original purchase from authorized dealers. During this period, AUBE technologies inc. will repair or replace the product with a new or of equivalent quality at AUBE’S option, without charge, any product proven defec- tive in normal use. Warranty does not cover transportation costs. Nor does it cover a product subjected to misuse or accidental damage. This warranty does not cover the cost of installation, removal or reinstallation. This limited warranty is in lieu of all other warranties, obligations or liabilities expressed or implied by the company. In no event shall AUBE technologies inc. be liable for con- sequential or incidental damages resulting from installation of this product. Some states or provinces do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. The defective product and the original sale receipt must be returned to the original dealer or shipped pre-paidt insured and addressed to: Aube technologies inc. 705, Montrichard Iberville (Quebec) Canada J2X 5K8 aubetech.com service@aubetech.com If you have any questions concerning the installation or programming of this product, please call our technical assistance at (450) 358-4600 for the Montreal area or 1-800-831-AUBE for outside area, Monday to Friday between 8:30 AM and 5:00 PM Eastern time. PROBLEMS AND SOLUTIONS PROBLEMS – No display – The LCD disappears but reappears after a 2 to 3 minute period – The thermostat is hot The thermostat is loosing the time but not the programming – Room temperature shown is wrong – Heating system always on – The thermostat displays heating but heating system is not turned on – Programs do not change as you want – Erratic or dim display CAUSES Circuit breaker is open Power failure Open linear limit control – The thermal protection unit on the baseboard heater opens after a power failure or a malfunction In normal use at full capacity (4000 W), the housing temperature of the thermostat can reach 35 to 40 oc Power failure more than 2 hours A draft is near the thermostat Bad installation Bad installation Incorrect programming hours Wrong programming mode selected SOLUTIONS Check 120 / 240 VAC presence at the thermostat – Ensure that the baseboard heater is not obstructed by furniture or curtains. Also verify that the linear limit control of the thermal protection unit is not touching the heating element – Eliminate the draft Check installation Check installation Check actual time in AM & PM as well as program times (AM is not displayed) Make sure operating mode is set to AUTO For a 500 W or less installation, the display could appear dim after the first power-up or a long power failure when the thermostat is in heat mode. See first power-up section 23/01/02 920-106-001-OO-I-B 4/4

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL



AUBE TH106 (01) PDF MANUAL

Leave a comment, question, review or page error below.

This site uses Akismet to reduce spam. Learn how your comment data is processed.