Click here to download ATLAS POWER ECM-2063 (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** ECM-2063 Owner’s Manual AC Power Distribution Sequencer Atlas Power —cM-æosa AC Power Distribution Sequencer Raceway Sy—tern oee:oeeo oee:oe eo Atlas 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. SOLInd Telephone: 800.876.3333 • Fax: 800.765.3435 AtlasSound.com Specifications are subject to change without notice.

****** Page 2 ****** ECM-2063 Owner’s Manual AC Power Distribution Sequencer Table of Contents Important Safety Instructions . .3 Introduction 5 Key Features 5 Applications 5 Raceway AC Inlet Knockouts … 6 Raceway Mounting Rails 6 Configuring the ECM-2063 Wiring the AC Mains .8 Specifications 13 Warranty 16 (A Atlas 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. SOL117d Telephone: 800.876.3333 Fax: 800.765.3435 AtlasSound.com Specifications are subject to change without notice.

****** Page 3 ****** Owner’s Manual Important Safety Instructions ATTENTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN RISQUE DE CHOC ÉLECTRIQUE – NE PAS OUVRIR. WARNING CAUTION ECM-2063 AC Power Distribution Sequencer The lightning flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage ” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 12. 13. 14. 15. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this device near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other device (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the device. 11. Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the device. When a cart is used, use caution when moving the cart/device combination to avoid injury from tip-over. Unplug this device during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the device has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the device, the device has been exposed to rain or moisture, does not operate normally, or has been dropped. WARNING: To reduce the risk of fire or electric shock, this device should not be exposed to rain or moisture and objects filled with liquids, such as a vase, should not be placed on this device. 16. To completely disconnect this equipment from the mains, disconnect the power supply cord plug from the receptacle. 17. The mains plug of the power supply cord shall remain readily operable. Atlas 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. SOLInd Telephone: 800.876.3333 • Fax: 800.765.3435 AtlasSound.com Specifications are subject to change without notice.

****** Page 4 ****** ECM-2063 Owner’s Manual AC Power Distribution Sequencer WARNING When The Device Is In Use To prevent electric shock, do not remove the product cover as there are high voltage components inside. Refer all servicing to Atlas Sound. Should any of the following irregularities occur during use, immediately switch off the power, disconnect the power cord from the AC outlet and contact Atlas Sound. Do not to attempt to continue operation with the product as this may cause fire or electric shock: Smoke or strange smell coming from the unit. If the product falls or the case is damaged. If water or any metallic objects falls into the product. If the power supply cord is damaged in any way. If the unit is malfunctioning. Do not insert or drop metallic objects or flammable materials into the ventilation holes of the product’s cover, as this may result in electric shock or fire. Do not place any containers with liquid or metallic objects on the top of the product. If any liquid spills into the unit, fire or electric shock may result. Never operate this product or touch the power supply cord during an electrical storm, electric shock may result. Never exceed the power rating on the product when connecting equipment. Fire and/or property damage may result. Operate the product only with the voltage specified on the unit. Fire and/or electric shock may result if a higher voltage is used. Do not modify, kink, or cut the power cord. Do not place the power cord in close proximity to heaters and do not place heavy objects on the power cord, including the product itself, doing so may result in fire or electrical shock. Ensure that the safety ground terminal is connected to a proper ground. Never connect the ground to a gas pipe as a catastrophic disaster may result. Be sure the installation of the product is stable, avoid slanted surfaces as the product may fall and cause injury or property damage. CAUTION When Installing The Product Plugging in or unplugging the power cord with wet hands may result in electric shock. Never move the unit with the power cord plugged into the wall, as damage to the power cord may result. When unplugging the cord from the wall, grasp the plug, NOT the cord. Never install this product in humid or dusty locations, nor in direct sunlight, near sources of heat, or in areas where sooty smoke or steam are present. Fire and electric shock may result. Keep all sides of the unit at least 31/2″ away from objects that may obstruct air flow to prevent the unit’s internal temperature rise. CAUTION When The Product Is In Use Never place heavy objects on the product, causing it to fall and/or break, resulting in personal injury and property damage. In addition, the product itself may fall and cause injury and property damage. Contact Atlas Sound for instructions on cleaning the inside of the unit. Large accumulations of dust inside the unit may result in heat buildup and fire. Ensure that the power supply plug is securely plugged into the wall outlet. Never allow dust to accumulate on the power plug or inside the wall outlet. When cleaning the unit or the unit is not to be operated for an extended period, unplug the power cord from the wall. (A Atlas 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. Sound Telephone: 800.876.3333 Fax: 800.765.3435 AtlasSound.com Specifications are subject to change without notice.

****** Page 5 ****** ECM-2063 Owner’s Manual AC Power Distribution Sequencer Introduction Thank you for purchasing the Atlas Power ECM-2063 AC Power Distribution Sequencer Raceway System. The ECM-2063 is designed to offer the installer/contractor current requirement flexibility based on the needs of the equipment that will be connected to the raceway. The ECM-2063 accepts up to three separate 20A 120VAC lines, allowing for up to a total of 60A to be divided throughout the system. The ECM-2063 features 6 individual AC 120V outlet sections that can be activated individually or in a sequenced order. Triggering a section or sequential order can be accomplished via a remote switch or by using a sequence controller like the Atlas Power TSD-SEQ6 or ECS-6RM The ECM-2063 features a total of 1 2, 120VAC outlets that are divided into 6 sections. Each section has an activation control port and a bi-color LED. This LED will display green to indicate that AC voltage is present at that specific AC section when it is activated or triggered and the LED will display red to indicate that the section is in Stand-By mode. Activation has been made easy, simply short the two pins of the control port for the specific channel you want triggered ON. This can be accomplished within a few feet of the ECM-2063 or from several feet away by using an Atlas Power sequence controller or via a switch. The ECM-2063 was designed to be compact measuring only 37″ high, 3.5″ wide and 2.75′ deep. The ECM-2063 can be mounted into most racks that have 481 internal height. The raceway can be mounted using the raceway mounting tabs which are designed to breakaway if needed to fit into tighter areas making it adaptable to secure the raceway in most applications. For your convenience there are six 1/2″ & dual knockouts that support standard electrical conduit components for wiring 120VAC mains into the raceway housing from the electrical panel. Note: For your safety all electrical wiring must be done by a qualified electrician. Key Features Compact design 3TH x 3.5W x 2.75″D 6 Separate 120V Outlet Sections 12, 120VAC 20A Outlets Accepts up to 3 20A 120VAC Lines, Configurable Incoming AC present LED Active LED Remote or Local Activation Hard Switch Contact Closure Trigger 6 Dual Knockouts h” & 3/4″ 4 Rail Mounting Tabs Applications The Atlas Power ECM-2063 was designed to be flexible, incorporating features that allow it to be used in a variety of applications. The sequenced outputs allow equipment to be turned ON or OFF in a particular order. This prevents an in-rush of current that could potentially damage connected electronics and eliminates audible pops that often occur with non-sequenced power activation. The following are just a few examples of applications in which the Atlas Power ECM-2063 can be used: Restaurants Houses of Worship Schools Home Theaters Office Buildings Sports Bars Industrial Facilities Atlas 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. SOLInd Telephone: 800.876.3333 • Fax: 800.765.3435 AtlasSound.com Specifications are subject to change without notice.

****** Page 6 ****** ECM-2063 Owner’s Manual AC Power Distribution Sequencer Raceway AC Inlet Knockouts The ECM-2063 can support up to three AC conduit inlets at each end. There are three knockouts on both the top and the bottom of the raceway. Each inlet supports a double knockout size supporting standard USA electrical fittings of 1/2″ and 3/4″ The figure below is an illustration of one end of the raceway. Raceway Mounting Rails The ECM-2063 raceway has breakaway rail mounting tabs that make it convenient to secure the raceway in most applications. There are four rails to secure the ECM-2063 to a cabinet or wall. Multiple slots are provided for ease of installation. To break the rail tabs off, simply bend the rail tabs back and forth with a pair of pliers until the metal separates. Note: After the metal breaks, sharp corners may need to be filed to prevent injury. as.a4 (525) o o o •ooo (3.26 ) 2.59 O (A Atlas 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. SOL117d Telephone: 800.876.3333 Fax: 800.765.3435 AtlasSound.com Specifications are subject to change without notice.

****** Page 7 ****** ECM-2063 Owner’s Manual AC Power Distribution Sequencer Configuring the ECM-2063 The ECM-2063 is designed to be activated/triggered by a sequence controller like the Atlas Power TSD-SEQ6 or the ECS-6RM. The ECM-2063 can be configured to accept from 1 to 3 separate hard wired 20A circuits. There are three individual load sections in the ECM-2063. Each load section has two separate sequence channels, with each channel having two 20A, 120VAC outlets. In summary, the ECM-2063 has a total of 12 AC outlets divided into 6 sequenced channels that can be divided or combined into 3 20A circuits. Note: All electrical wiring must be done by a certified electrician. AC ’20V – AC IOA Channel Control Ports There are 6 channel control ports that correspond with the 6 AC outlet channels. Activation or triggering a channel of the ECM-2063 is done by shorting two of the channel control port pins together. An activation sequence can be triggered using a TSD-SEQ6 or ECS- 6RM sequence controller or by using another external device such as a hard contact switch to trigger a channel. If a section is required to be “always ON” , connect a jumper between the control port pins to the corresponding channel. Channel Status Indicators Each channel has a bi-color LED that designates the status of that specific channel. No LED illuminated indicates there is no AC Mains power present at that channel. Red illumination indicates there is AC Mains power present and that channel is ready to be activated. Green illumination indicates the corresponding AC output channel is active and 120VAC is present. To Activate a Channel, Short Two Contacts CHI CH2 CH3 CH4 Channel Status CH5 Atlas Power ECM-2063 AC Power Distribution Sequencer CHB 20A x 3 Configurable AC 120V 60Hz GOA A” C.enb”d Not To ØA WARNING Note: All wiring must be done by a qualified electrician. Green Active • Red Standby • No Color No AC Power 1601 Jag* McKay Blvd. • Ennis, TX 75119 • 820.876.3333 • Load Distribution There are four different load distribution combinations for the ECM-2063. The ECM-2063 has 6 channels that are divided into three load circuits. This is to allow up to three separate 20A 120VAC mains lines to be applied to the ECM-2063. It is not required to apply three circuits; you can parallel a single 20A line to all three load sections. Channels 1 & 2 are connected to Ll Channels 3 & 4 are connected to L2 Channels 5 & 6 are connected to L3 Atlas 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. SOLInd Telephone: 800.876.3333 • Fax: 800.765.3435 AtlasSound.com Specifications are subject to change without notice.

****** Page 8 ****** ECM-2063 Owner’s Manual AC Power Distribution Sequencer Wiring the AC Mains Below are four configurations for load distribution. After following the wiring diagram place the label of the Internal Wiring Configuration on the panel box. Note: All electrical wiring must be done by a certified electrician. Follow the steps below for wiring the AC mains. Accessing the Internal Wiring . Locate the Control Input Panel. Remove the four screws. (See diagram below) Remove the Control Input Panel. Note: A ribbon cable is attached. Carefully lay panel aside leaving the cable attached. Do not pull on cable or damage may occur. Select the load configuration from the wiring diagram that applies on the following pages. Carefully place the input panel back onto the raceway paying close attention to the ribbon cable to ensure that it does not 1 2. 3. 4. 5. 6. 7. become twisted or pinched between the panel and the chassis. Secure the Control Input Panel Select the proper Internal Wiring Label and place it on the front panel. o o (A Atlas 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. SOL117d Telephone: 800.876.3333 Fax: 800.765.3435 AtlasSound.com Specifications are subject to change without notice.

****** Page 9 ****** ECM-2063 Owner’s Manual AC Power Distribution Sequencer ECM-2063 Load Wiring Option #1 – Ll, L2, L3 = 20A In this load/current wiring configuration all 3 load sections (Channels 1 — 6) are connected to a single 20A AC Mains feed. Note: All electrical wiring must be done by a certified electrician. 1 2. 3. 4. 5. Follow the steps listed in section “Accessing the Internal Wiring” Choose the most convenient AC Mains inlet on the bottom of the raceway that allows for the easiest connection to the AC Mains line based on the layout of the installation. Strip the wires 3/8″ Locate J23 Ll on the PCB. Insert the following wires into J23 Ll and secure by tightening the screws firmly: Ground (Green GRN) wire into Pin 1 labeled “G” • Neutral (White WHT) wire into Pin 2 labeled “N” Hot (Black BLK) wire into Pin 3 labeled “I-I” Leave all other wires within the chassis alone and intact. Ll, L2, L3 = 20A Internal Wiring Identification Label (To be placed on Input Plate if configured in this manner) CHI o 13 G N L2 G N CHP o BLK Hot WAT Neutral GND Green CH3 o nstalleris Wiring CH4 o CH5 o CH6 o Atlas 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. SOLInd Telephone: 800.876.3333 • Fax: 800.765.3435 AtlasSound.com Specifications are subject to change without notice.

****** Page 10 ****** ECM-2063 Owner’s Manual AC Power Distribution Sequencer ECM-2063 Load Wiring Option #2 – Ll & L2 = 20A, L3 = 20A In this load/current wiring configuration the load sections Ll & L2 (Channels & 4) are connected to a single 20A AC Mains feed and load section L3 (Channels 5 & 6) is connected to second 20A AC Mains feed. Note: All electrical wiring must be done by a certified electrician. 2. 3. 4. 5. 6. 7. Follow the steps listed in section “Accessing the Internal Wiring” Choose the most convenient AC Mains inlet on the bottom of the raceway that allows for the easiest connection to the AC Mains line based on the layout of the installation. Strip the wires 3/8″. Locate J25 L3 on the PCB. Remove the wire jumpers from P2 “N” and P3 II-I”. Remove wire from push on spade lug, discard 2 wires. Ll & L2 wiring: Locate J23 Ll on the PCB. Insert the 20A AC Mains wires into J23 Ll and secure by tightening the screws firmly. Ground (Green GRN) wire into Pin 1 labeled “G” Neutral (White WHT) wire into Pin 2 labeled “N” • Hot (Black BLK) wire into Pin 3 labeled “H” L3 wiring: Locate J25 L3 on the PCB. Insert the second AC Mains wires into J25 L3 and secure by tightening the screws firmly. Ground (Green GRN) wire into Pin 1 labeled “G” Neutral (White WHT) wire into Pin 2 labeled “N” Hot (Black BLK) wire into Pin 3 labeled “H” Leave all other wires within the chassis alone and intact. Ll & L2 = 20A L3 = 20A Internal Wiring Identification Label (To be placed on Input Plate if configured in this manner) CHI o CH2 o BLK Hot WAT Neutral GND Green CH3 o G CH4 o CH5 o 13 G N 12 G N (A Atlas Sound N H CH6 o BLK Hot WHT Neutral GND Green AtlasSound.com Installer’s Wiring 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. Telephone: 800.876.3333 Fax: 800.765.3435 – 10- Specifications are subject to change without notice.

****** Page 11 ****** ECM-2063 Owner’s Manual AC Power Distribution Sequencer ECM-2063 Load Wiring Option #3 – Ll = 20A, L2 & L3 = 20A In this load/current wiring configuration the load section Ll (Channels 1 & 2) is connected to a single 20A AC Mains feed and load sections L2 & L3 (Channels 3, 4, 5, 6) are connected to second 20A AC Mains feed. Note: All electrical wiring must be done by a certified electrician. 1 2. 3. 4. 5. 6. 7. Follow the steps listed in section “Accessing the Internal Wiring” Choose the most convenient AC Mains inlet on the bottom of the raceway that allows for the easiest connection to the AC Mains line based on the layout of the installation. Strip the wires 3/8″ Locate J24 Ll on the PCB. Remove the wire jumpers from P2 “N” and P3 ‘1–1″ Remove wire from push on spade lug, discard 2 wires. Ll wiring: Locate J23 Ll on the PCB. Insert the 20A AC Mains wires into J23 Ll and secure by tightening the screws firmly. Ground (Green GRN) wire into Pin 1 labeled “G” Neutral (White WHT) wire into Pin 2 labeled “N” • Hot (Black BLK) wire into Pin 3 labeled “H” L2 & L3 wiring: Locate J24 L2 on the PCB. Insert the second AC Mains wires into J24 L2 and secure by tightening the screws firmly. Ground (Green GRN) wire into Pin 1 labeled “G” Neutral (White WHT) wire into Pin 2 labeled “N” Hot (Black BLK) wire into Pin 3 labeled “H” Leave all other wires within the chassis alone and intact. CHI o Ll = 20A L2 & L3 = 20A Internal Wiring Identification Label (To be placed on Input Plate if configured in this manner) CH2 o CH3 o CHA o BLK Hot WHT Neutral GND Green CH5 o BLK Hot WI-IT Neutral GND Green Installer’S Atlas 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. SOLInd Telephone: 800.876.3333 • Fax: 800.765.3435 11- Specifications are subject to change without notice. CH6 o AtlasSound.com

****** Page 12 ****** ECM-2063 Owner’s Manual AC Power Distribution Sequencer ECM-2063 Load Wiring Option #4 – Ll = 20A, L2 = 20A, L3 = 20A In this load/current wiring configuration the load section Ll (Channels 1 & 2) is connected to a single 20A AC Mains feed, load section L2 (Channels 3 & 4) is connected to second 20A AC Mains feed and load section L3 (Channels 5 & 6) is connected to third 20A AC Main feed. Note: All electrical wiring must be done by a certified electrician. 1 2. 3. 4. 5. 6. 7. 8. 9. Follow the steps listed in section “Accessing the Internal Wiring” Choose the most convenient AC Mains inlet on the bottom of the raceway that allows for the easiest connection to the AC Mains line based on the layout of the installation. Strip the wires 3/8″ Locate J24 Ll on the PCB. Remove the wire jumpers from P2 “N” and P3 ‘1–1″ discard 2 wires. Locate J25 Ll on the PCB. Remove the wire jumpers from P2 “N” and P3 ‘H” discard 2 wires. Remove wire from push on spade lug, Remove wire from push on spade lug, Ll wiring: Locate J23 Ll on the PCB. Insert the 20A AC Mains wires into J23 Ll and secure by tightening the screws firmly. Ground (Green GRN) wire into Pin 1 labeled “G” Neutral (White WHT) wire into Pin 2 labeled “N” Hot (Black BLK) wire into Pin 3 labeled “H” L2 wiring: Locate J24 L2 on the PCB. Insert the second AC Mains wires into J24 L2 and secure by tightening the screws firmly. Ground (Green GRN) wire into Pin 1 labeled “G” Neutral (White WHT) wire into Pin 2 labeled “N” Hot (Black BLK) wire into Pin 3 labeled ill-I” L3 wiring: Locate J25 L3 on the PCB. Insert the third AC Mains wires into J25 L3 and secure by tightening the screws firmly. Ground (Green GRN) wire into Pin 1 labeled “G” Neutral (White WHT) wire into Pin 2 labeled “N” Hot (Black BLK) wire into Pin 3 labeled “H Leave all other wires within the chassis alone and intact. CHI o Ll = 20A L2 = 20A L3 = 20A Internal Wiring Identification Label (To be placed on Input Plate if configured in this manner) CH2 o CH3 o CHA o CH5 o BLK Hot WI-IT Neutral GND Green BLK Hot WHT Neutral GND Green Installer’S Wiring CH6 o BLK Hot WHT Neutral GND Green (A Atlas 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. Sound AtlasSound.com Telephone: 800.876.3333 Fax: 800.765.3435 12- Specifications are subject to change without notice.

****** Page 13 ****** ECM-2063 Owner’s Manual Specifications Type RoHS Compliant Safety Listing Front Panel Number of Channels AC Outlets Connectors Remote Trigger Indicators AC Mains Interconnect Technical Data Voltage Load Power Consumption Mechanical Chassis Finish Mounting Electrical Inlets Electrical Inlet Size Height Width Length Weight AC Power Distribution Sequencer Electrical AC Power Distribution Yes ETL (UL60065 Standard) 6 12 NEMA 5-20, Switched Qty 6, 2 Position Phoenix Euro Block Style 3.5mm Spacing Hard Switch Contact Closure Incoming AC (Red), Active (Green) Screw Terminal Block 120V AC 601-lz 20A + 20A + 20A Configurable 5. IW Standby, 11.3W Active Black Paint Rail Tabs 6 1/2″ and 3/4″ Dual Knockout 2.59′ (65.79mm) 3.26″ (82.80mm) 36.84′ (935.74mm) 10 lbs (4.54kg) Atlas 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. SOLInd Telephone: 800.876.3333 • Fax: 800.765.3435 13- Specifications are subject to change without notice. AtlasSound.com

****** Page 14 ****** Notes: AtlasSound.com ECM-2063 Owner’s Manual AC Power Distribution Sequencer (A Atlas 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. Sound Telephone: 800.876.3333 Fax: 800.765.3435 — 14 Specifications are subject to change without notice.

****** Page 15 ****** Owner’s Manual Notes: Atlas ECM-2063 AC Power Distribution Sequencer 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. SOLInd Telephone: 800.876.3333 • Fax: 800.765.3435 15- Specifications are subject to change without notice. AtlasSound.com

****** Page 16 ****** ECM-2063 Owner’s Manual AC Power Distribution Sequencer Limited Warranty All products manufactured by Atlas Sound are warranted to the original dealer/lnstaller, industrial or commercial purchaser to be free from defects in material and workmanship and to be in compliance with our published specifications, if any. This warranty shall extend from the date of purchase for a period of three years on all Atlas Sound products, including SOUNDOLIER brand, and ATLAS SOUND brand products except as follows: one year on electronics and control systems; one year on replacement parts; and one year on Musician Series stands and related accessories. Additionally, fuses and lamps carry no warranty. Atlas Sound will solely at its discretion, replace at no charge or repair free of charge defective parts or products when the product has been applied and used in accordance with our published operation and installation instructions. We will not be responsible for defects caused by improper storage, misuse (including failure to provide reasonable and necessary maintenance), accident, abnormal atmospheres, water immersion, lightning discharge, or malfunctions when products have been modified or operated in excess of rated power, altered, serviced or installed in other than a workman like manner. The original sales invoice should be retained as evidence of purchase under the terms of this warranty. All warranty returns must comply with our returns policy set forth below. When products returned to Atlas Sound do not qualify for repair or replacement under our warranty, repairs may be performed at prevailing costs for material and labor unless there is included with the returned product(s) a written request for an estimate of repair costs before any nonwarranty work is performed. In the event of replacement or upon completion of repairs, return shipment will be made with the transportation charges collect. EXCEPT TO THE EXTENT THAT APPLICABLE LAW PREVENTS THE LIMITATION OF CONSEQUENTIAL DAMAGES FOR PERSONAL INJURY, ATLAS SOUND SHALL NOT BE LIABLE IN TORT OR CONTRACT FOR ANY DIRECT, CONSEQUENTIAL OR INCIDENTAL LOSS OR DAMAGE ARISING OUT OF THE INSTALLATION, USE OR INABILITY TO USE THE PRODUCTS. THE ABOVE WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Atlas Sound does not assume, or does it authorize any other person to assume or extend on its behalf, any other warranty, obligation, or liability. This warranty gives you specific legal rights and you may have other rights which vary from state to state. Service Should your ECM-2063 require service, please contact the Atlas Sound warranty department at 1-877-689-8055, ext. 277 to obtain an RA number. Atlas Sound Tech Support can be reached at 1-800-876-3333. Visit our website at AtlasSound.com to see other Atlas products. @2012 Atlas Sound L.P. All rights reserved. Atlas Sound is a trademark of Atlas Sound L.P. All other trademarks are the property of their respective owners. ATS004222 RevB 5/12 (A Atlas 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. Sound AtlasSound.com Telephone: 800.876.3333 Fax: 800.765.3435 -16- Specifications are subject to change without notice.

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL



ATLAS POWER ECM-2063 (01) PDF MANUAL

Leave a comment, question, review or page error below.

This site uses Akismet to reduce spam. Learn how your comment data is processed.