Click here to download ATLAS METAL HB-5 (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** ATLAS METAL 1 135 N.W. 159th DRIVE, MIAMI, FLORIDA 33 69 TEL 305.625.2451 TOLL FREE 800.762.7565 FAX 305.623.0475 WWW.ATLASFOODSERV.COM HEATED BASE-HB SERIES Service and Installation Manual SALES@ATLASFOODSERV.COM Please read this manual completely before attempting to install or operate this equipment! Notify carrier of damage! Inspect all components immediately. See page 2. HEATED BASE-HB SERIES ELECTRICALLY HEATED UNDER-COUNTER Effective Date: 2019 IMPORTANT INFORMATION READ BEFORE USE

****** Page 2 ****** CONTENTS RECEIVING & INSPECTING EQUIPMENT SERIAL AND MODEL # LOCATION HB – SPECIFICATIONS, FEATURES AND ACCESSORIES ELECTRICAL CHARACTERISTICS AND CUT-OUT REQUIREMENTS OPERATION AND S/S MAINTENANCE PARTS LIST TROUBLE SHOOTING GUIDE ELECTRICAL SCHEMATIC LIMITED WARRANTY WARRANTY INFORMATION RECEIVING AND INSPECTING THE EQUIPMENT 1. VISUALLY INSPECT THE SHIPPING CRATE. DAMAGE SHOULD BE NOTED AND REPORTED TO THE DELIVERING CARRIER. 2. IF DAMAGED, OPEN AND INSPECT CONTENTS WITH CARRIER. 3. IF CRATE IS NOT DAMAGED AND THERE IS CONCEALED DAMAGE TO THE EQUIPMENT, NOTIFY THE CARRIER. NOTIFICATION MUST BE MADE VERBALLY AND IN WRITING. 4. REQUEST AN INSPECTION BY THE SHIPPING COMPANY FOR THE DAMAGED EQUIPMENT WITHIN 1 0 DAYS FROM RECEIPT OF THE EQUIPMENT 5. FREIGHT CARRIERS CAN SUPPLY THE NECESSARY FORMS ON REQUEST. 6. SAVE ALL CRATING MATERIALS UNTIL INSPECTION HAS BEEN MADE OR WAIVED. SERIAL NUMBER LOCATION THE SERIAL AND MODEL# CAN BE FOUND ON THE OPERATORS CONTROL PANEL. WHEN CALLING ATLAS FOR PARTS AND SERVICE ALWAYS HAVE THIS INFORMATION AVAILABLE. SERIAL MODEL INSTALLATION DATE:

****** Page 3 ****** ATLAS METAL 1 135 N.W 159th DRIVE, MIAMI, FLORIDA 33 169 TEL 305.625.2451 TOLL FREE 800.762.7565 FAX 305.623.0475 WWW.ATLASFOODSERV.COM SALES@ATLASFOODSERV.COM Project: Item No.. Quantity: SLIDE-IN SERVING EQUIPMENT HEATED BASE Electrically Heated Under Counter ü HB-3 HB-4 OHB-5 HB_3 SPECIFICATIONS BODY: Double wall constructed with 20 gauge, type 304 stainless steel interior liner, with coved corners. Exterior wall is 22 gauge galvanized steel, with an 18 gauge stainless steel facia. The body is filled with 1″ of high density fiber- glass insulation on all sides. Interior of the body is provided with a removable slide assembly to accommodate 12″ X 20″ pans. DOORS: Doors are double wall constructed of 18 gauge, type 304 stainless steel, fully insulated with high density fiberglass, and provided with edge mounted, chrome plated hinges and a slam action latch. Doors are complete with a moisture-proof gasket. ELECTRICAL: The unit is provided with an 850 watt ele- ment, pre-wired to an on/off thermostat switch and pilot light. The unit is wired for 15 amp. , 120 volt, single phase opera- tion, with a 6′ long, 3-wire cord and plug (NEMA 5-15P). Specifications subject to change without notice. STANDARD FEATURES D Slides into your counter – puts heated storage where you need it Fully insulated for maximum efficiency Slide assembly for standard 12″ x 20″ pans Electrically heated – thermostat control I-Year Parts & Labor Warranty D UL Listed Dl-57

****** Page 4 ****** 23-5/8″ 15-3/4″ 14-1/8″ MODEL PLAN VIEW FRONT ELEVATION 29-1/8″ ATLAS METAL atlosfoodserv.com COMMERCIAL FOOD WARMER 586M 14-5/8″ END VIEW ELECTRICAL SHIP WT. CHARACTERISTICS (LBS.) 41-7/8″ HB_3 (106cm) 55-5/8″ HB-4 (140.9cm) 69-3/8″ HB_5 (175.8cm) STORAGE CAPACITY 12″ X 20″ PANS 8 12 16 CUT-OUT REQUIRED 15-3/4″ x 41-7/8″ (40 X 106cm) 15-3/4″ x 55-5/8″ (40 X 140.9cm) 15-3/4″ x 69-3/8″ (40 X 175.8cm) 850 w – 7.1 120V 850 w- 7.1 120V 850 w – 7.1 120V amps. amps. amps. 190 (86. Ikg) 265 (120.2kg) 312 (141.5kg) Atlas Metal Industries Dl-58 e 1135 NW 159th Dr. Miami, FL 33169 • (800) 762-7565 Fax: (305) 623-0475 e atlasfoodserv.com 2/19-sc

****** Page 5 ****** SLIDE- IN HEATED BASE HB SERIES OPERATION The unit is ready to operate as soon as it is plugged in and turned on. The thermostat has an off position and numbers from #1 through #10 (number 10 is the highest setting). The unit is supplied with a power cord and NEMA plug. Refer to the data plate for the amperage and voltage information. Use a licensed electrician when installing power source. MAINTENANCE NEVER CLEAN THE UNIT WITH A CHLORIDE BASED PRODUCT. CHLORIDES OR IMPROPER CLEANING COULD SCAR, MARK AND/OR CORRODE METAL. DO NOT USE STEEL WOOL OR ABRASIVE PRODUCTS. TO CLEAN USE SOAPY WARM WATER, RINSE THOROUGHLY TO REMOVE ALL RESIDUES. FAILURE TO MEET THESE CONDITIONS WILL VOID WARRANTY.

****** Page 6 ****** ATLAS METAL Subsidiary of Mercury Aircraft, Inc. 1135 N.W. 159th DR., MIAMI, FL 33169 PHONE (305) 625-2451, (800) 762-7565, FAX (305) 623-0475, E-mail: sales@atlasfoodserv.com PARTS LIST ELECTRICAL HEATED BASE HB SERIES 10 ITEM NUMBER 1 2 3 4 5 6 7 8 9 10 11 12 13 2 8 9 P ART NUMBER 1001-0 1002-0 22-1407 1100-0 1105-0 7010-3 7013-3 S83754-4 S83753-o 6055-1 6052-1 S83754-3 6053-8 1087-0 2500-1 1053-0 1054-0 1055-0 4 1 7 3 HB-4 SHOWN DESCRIPTION 6 5 Power Cord 14/3-15 Amps 240V Power Cord 14/3-15 Am s 120V Thermostat Knob Pilot Light Thermometer #3 & #4 Door Gasket #4 & #5 Door Gasket Door Assembly HB-5 Pan Rack Slam Action Latch Slam Action W/ Lock Door Assembly HB-3, HB-4 Hinge & Cover Cord Connector (Not Shown) Thermostat (Not Shown) 120V / 850W Element (Not Shown) 208 V / 850W Element ot Shown 240V / 850W Element ot Shown

****** Page 7 ****** ATLAS Subsidiary of Mercury Aircraft, Inc. METAL 1135 N.W. 159th DR., MIAMI, FL 33169 PHONE (305) 625-2451, (800) 762-7565, FAX (305) 623-0475, E-mail: sales@atlasfoodserv.com Electric Hot Food Drop-In Trouble Shooting Guide Symptom Unit not plugged in. No power at receptacle. Unit will not heat Probable Cause Thermostat and or switch not in the on position. Call factory for service at 1-800-762-7565 Thermostat’s not turned to the highest setting. Food products not hot enough when placed in unit. Food products not Food product not being stirred or rotated. hot enough. Heat lamp or head strip over the food product is recommended. Call factory for service at 1-800-762-7565. NOTE: Before starting any warranty repair work you must first call the factory for authorization. Failure to do so can make you responsible for repair cost.

****** Page 8 ****** o o 1 z o 1 o 0

****** Page 9 ****** ATLAS LIMITED WARRANTY TAL Atlas Metal Industries, Inc. warrants to the Purchaser of this product that the same shall be free from defects in the workmanship and material for a period of one year from the date of original installation of the equipment, but not to exceed eighteen (18) months after date of shipment from factory. During this period of time Atlas Metal Industries, Inc. will replace all defective parts and will pay for authorized replacement labor. Replacement and installation of such parts and labor shall be provided only upon prior written authority of Atlas Metal Industries, Inc. The Refrigeration warranty is for a twenty (20) month time period and includes supplying the compressor at a no charge basis provided the damage to the compressor was not caused by the customer or end user. Authorized replacement labor will be paid for a period of one year from date of installation. Freight costs for defective unit to and from Atlas Metal Industries, Inc. are not included, and all defective parts must be returned to the factory freight prepaid for evaluation. ALL WARRANTY LABOR MUST BE AUTHORIZED BY ATLAS METAL INDUSTRIES, INC. PRIOR TO THE ACTUAL WORK BEING DONE. This warranty does not apply to any equipment or any part thereof, which has been subjected to shipping damage, improper voltage, alteration, abuse or misuses, and does not cover loss of food, other products, or damage to property due to mechanical or electrical malfunction. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION OF THE FACE HEREOF. SELLER DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OF THE GOODS OR THE FITNESS OF THE GOODS FOR ANY PURPOSE AND BUYER AGREES THAT THE GOODS ARE SOLD “AS IS.”

****** Page 10 ****** ATLAS METAL WARRANTY INFORMATION In order to have your invoice approved for payment by the factory, please note the followinq: An authorization number must be obtained from the factory prior to performing any warranty service. Atlas Metal will not approve excessive labor due to poor access to the unit being serviced. If design does not allow reasonable access, contact the factory. All travel time that exceeds 100 miles round trip must be authorized by the factory. Thank You: Warranty service Dept.


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL

ATLAS METAL HB-5 (01) PDF MANUAL

Leave a comment, question, review or page error below.

This site uses Akismet to reduce spam. Learn how your comment data is processed.