PDF Content Summary:
****** Page 1 ****** VA229Q/VP229Q/ VP229HE Series LCD Monitor User Guide Homu HIGH-DEFINITION MULTIMEDIA INTERFACE
****** Page 2 ****** First Edition August 2020 Copyright 0 2020 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for bækup purposes, without the express written permission of ASUSTeK COMPUTER INC. CASUS) Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL UAS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT. SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY. AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.
****** Page 3 ****** Contents Contents ….. ….. ….. ….. ……………………………………………………. ….. …. iii Notices iv Safety information vi Care & Cleaning vii Takeback Services viii TCO certified ….. ….. ….. .. ….. …. ix Chapter 1: Product introduction ….. ….. .. 1-1 Package contents………………………………………………………………. 1 1 ….. ….. ….. …………… 1-2 Outline dimensions………………………………………………………….. 3 11 3-13 Supported operating modes ….. ….. ….. ….. …………………………… 3 14 1.1 1.2 1.3 Welcome! Monitor introduction ….. ….. ….. ….. ……………… 1.3.1 1.3.2 Chapter 2: Front view 1-2 Back view 1-3 Setup 2.1 2.2 2.3 2.4 2.5 2-1 Assembling the monitor arm/base Detaching the arm/base (for VESA wall mount) 2-2 Chapter 3: General instructions . 2-4 Adjusting the monitor………………………….. … .. Connecting the cables……………………………………………………….. 2 5 Turning on the monitor………………………………………………………. 2 6 . 3-1 3-1 3.1 3.2 3.3 3.4 3.5 OSD (On-Screen Display) menu . 3.1.1 How to reconfigure ………………………………………………….3 1 3.1.2 OSD function introduction 3-9 Specifications summary Troubleshooting (FAQ)…………….. iii
****** Page 4 ****** Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. Increæe the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. ENERGY STAR complied product ENERGY STAR ENERGY STAR is a joint program of the U.S. Environmental Protection Agency and the U.S. Department of Energy helping us all save money and protect the environment through energy efficient products and practices. All ASUS products with the ENERGY STAR logo comply with the ENERGY STAR standard, and the power management feature is enabled by default. The monitor and computer are automatically set to sleep after 10 and 30 minutes of user inactivity. To wake your computer, click the mouse or press any key on the keyboard. Please visit energystar.gov/powermanagement for detail information on power management and its benefits to the environment. In addition, pleæe visit http ://energystar.gov for detail information on the ENERGY STAR joint program. iv
****** Page 5 ****** NOTE: Energy Star is NOT supported on FreeDOS and Linux-based operating system. Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. This class B digital apparatus complies with Canadian ICES-003. This Class B digital apparatus meets all requirements of the Canadian Interference – Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouiller du Canada.
****** Page 6 ****** Safety information Before setting up the monitor, carefully read all the documentation that came with the package. To prevent fire or shock hazard, never expose the monitor to rain or moisture. Never try to open the monitor cabinet. The dangerous high voltages inside the monitor may result in serious physical injury. If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer. Before using the product, make sure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately. Slots and openings on the back or top of the cabinet are provided for ventilation. Do not block these slots. Never place this product near or over a radiator or heat source unless proper ventilation is provided. The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supply to your home, consult your dealer or local power company. Use the appropriate power plug which complies with your local power standard. Do not overload power strips and extention cords. Overloading can result in fire or electric shock. Avoid dustJ humidity, and temperature extremes. Do not place the monitor in any area where it may become wet. Place the monitor on a stable surface. Unplug the unit during a lightning storm or if it will not be used for a long period of time. This will protect the monitor from damage due to power surges. Never push objects or spill liquid of any kind into the slots on the monitor cabinet. To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100-240V AC. If you encounter technical problems with the monitor, contact a qualified service technician or your retailer. Adjustment of the volume control as well as the equalizer to other settings than the center position may increæe the ear-/headphones output voltage and therefore the sound pressure level. This symbol of the crossed out wheeled bin indicates that the product (electrical. electronic equipment, and mercury-containing button cell battery) should not be placed in municipal waste. Please check local regulations for disposal of electronic products. AEEE yönetmeliéine uygundur vi
****** Page 7 ****** Care & Cleaning Before you lift or reposition your monitor, it is better to disconnect the cables and power cord. Follow the correct lifting techniques when positioning the monitor. When lifting or carrying the monitor, grasp the edges of the monitor. Do not lift the display by the stand or the cord. Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor surface with a lint-free non-abrasive cloth. Stubborn stains may be removed with a cloth dampened with mild cleaner. Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended for use with the monitor. Never spray cleaner directly on the screen, as it may drip inside the monitor and cause an electric shock. The following symptoms are normal with the monitor: • You may find slightly uneven brightness on the screen depending on the desktop pattern you use. • When the same image is displayed for hours, an afterimage of the previous screen may remain after switching the image. The screen will recover slowly or you can turn off the Power Switch for hours. • When the screen becomes black or flashes, or cannot work anymore, contact your dealer or service center to fix it. Do not repair the screen by yourself! Conventions used in this guide WARNING: Information to prevent injury to yourself when trying to complete a tæk. CAUTION: Information to prevent damage to the components when trying to complete a tæk. IMPORTANT: Information that you MUST follow to complete a task. NOTE: Tips and additional information to aid in completing a task. vii
****** Page 8 ****** Where to find more information Refer to the following sources for additional information and for product and software updates. 1. 2. ASUS websites The ASUS websites worldwide provide updated information on ASUS hardware and software products. Refer to æus.com Optional documentation Your product package may include optional documentation that may have been added by your dealer. These documents are not part of the standard package. Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for our customers to be able to responsibly recycle our products, batteries and other components as well as the packaging materials. Please go to csr.æus.com/english/Takeback.htm for detail recycling information in different region. viii
****** Page 9 ****** TCO certified A third-partu certification according to ISO 14024 CERTIFIED Toward sustainable IT products O Say hello to a more sustainable product IT products are associated with a wide range of sustainability risks throughout their life cycle. Human rights violations are common in the factories. Harmful substances are used both in products and their manufacture. Products can often have a short lifespan because of poor ergonomics, low quality and when theg are not able to be repaired or upgraded. This product is a better choice. It meets all the criteria in TCO Certified, the world’s most comprehensive sustainability certification for IT products. Thank you for making a responsible product choice, that help drive progress towards a more sustainable futurel Criteria in TCO Certified have a life-cycle perspective and balance environmental and social responsibility. Conformitg is verified bu independent and approved verifiers that specialize in IT products, social responsibility or other sustainability issues. Verification is done both before and after the certificate is issued covering the entire validity period. The process also includes ensuring that corrective actions are implemented in all cases of factory non-conformities. And last but not least, to make sure that the certification and independent verification is accurate, both TCO Certified and the verifiers are reviewed regularly. Want to know more? Read information about TCO Certified, full criteria documents, news and updates at tcocertified@com. On the website you’ll also find our Product Finder, which presents a complete searchable listing of certified products- ix
****** Page 11 ****** 1.1 Welcome! Thank you for purchasing the ASUS@LCD monitor! The latest widescreen LCD monitor from ASUS provides a broader, brighter and crystal-clear display, plus a host of features that enhance your viewing experience. With these featuresJ you can enjoy the convenience and delightful visual experience that the monitor brings to you! 1.2 Package contents Check your package for the following items: LCD monitor Monitor base Quick start guide Warranty card Power cord HDMI cable (optional) DisplayPort cable (optional) VGA cable (optional) USB cable (optional) Mini PC Kit (optional) Cable holder If any of the above items is damaged or missing, contact your retailer immediately. ASUS VA229Q/ VP229Q/ VP229HE Series LCD Monitor 1-1
****** Page 12 ****** 1.3 1.3.1 Monitor introduction Front view VP229QNP229HE VA229QSB ooo O 1. 2. 3. 4. 1-2 Power button/power indicator • Turns the monitor on/off. • The color definition of the power indicator is as the below table. Status White Amber Off Description On Standby mode Off Menu button: Press this button to display the OSD menu when the OSD is off. Enters the OSD menu. Toggles the Key Lock function between on and off with a long press for 5 seconds. X Exit button: • Press this button to display the OSD menu when the OSD is off. Exits the OSD menu. @ Input select button: Press this button to display the OSD menu when the OSD is off. Selects an available input source. Chapter 1: Product introduction
****** Page 13 ****** 5. 6. Shortcut I • Press this button to display the OSD menu when the OSD is off. • Default: Brightness hotkey • To change the hotkey function, go to the Shortcut > Shortcut 1 menu. •V• Shortcut 2 Press this button to display the OSD menu when the OSD is off. Default: Blue light filter hotkey To change the hotkey function, go to the Shortcut > Shortcut 2 menu. 1.3.2 Back view VP229QNP229HE VA229QSB VP229HE VP229Q 123 1. 2. 3. 4. 5. 6. 7. AC-IN port. This port connects the power cord. Line in port. This port connects PC audio source by the audio cable. Earphone jack. This port is only available when an HDMI/DP cable is connected. DisplayPort in. This port is for connection with a DisplayPort compatible device. HDMI port. This port is for connection with an HDMI compatible device. VGA port. This 15-pin port is for PC VGA connection. USB 2.0 upstream port. This port is for connection with a USB upstream cable. The connection enables the USB ports on the monitor. 1-3
****** Page 14 ****** 8. 9. 10. 1-4 USB 2.0 downstream ports. These ports are for connection with USB devices, such as USB keyboard/mouse, USB flash drive, etc. Kensington lock slot. Control buttons. Chapter 1: Product introduction
****** Page 15 ****** 2.1 Assembling the monitor arm/base To assemble the monitor base: 1. 2. 3. 4. Have the front of the monitor face down on a table. Attach the base into the armJ making sure the tab on the arm fits into the groove on the base. VP229Q/ VP229HE: Fix the base to the arm by rotating the base until it fits into place. VA229QSB: Fix the bæe to the arm by fastening the bundled screw. VA229QSB: Remove the stop screw at the bottom of the base to allow 1 800 swiwel adjustment from either left or right We recommend that you cover the table surface with soft cloth to prevent damage to the monitor. VP229Q/VP229HE 6 VA229QSB 0 Base screw size: M6 x 16.5 mm. ASUS VA229Q/ VP229Q/ VP229HE Series LCD Monitor 6 ± 180 a 0 2-1
****** Page 16 ****** 2.2 Detaching the arm/base (for VESA wall mount) The detachable arm/base of this monitor is specially designed for VESA wall mount. To detach the arm/base: VP229Q/ VP229HE 1. 2. 3. 4. 5. 2-2 Have the front of the monitor face down on a table. Remove the rubbers in the four screw holes. (Figure 1) Remove the base (Figure 2). Remove the hinge cover (Figure 3). Use a screwdriver to remove the screw(s) on the hinge (Figure 4), then remove the hinge. (Figure 1) (Figure 4) (Figure 2) (Figure 3) Chapter 2: Setup
****** Page 17 ****** VA229QSB 2. 3. 4. Have the front of the monitor face down on a table. Remove the rubbers in the four screw holes. (Figure 1) Remove the bæe (Figure 2). Use a screwdriver to remove the screw(s) on the hinge (Figure 3), then (Figure 1) (Figure 2) (Figure 3) We recommend that you cover the table surface with soft cloth to prevent damage to the monitor. The VESA wall mount kit (100 x 100 mm) is purchased separately. Use only the UL Listed Wall Mount Bracket with minimum weight/load 22.7kg (Screw size: M4x 10 mm) 2-3
****** Page 18 ****** 2.3 Adjusting the monitor For optimal viewing, we recommend that you look at the full face of the monitor, then adjust the monitor to the angle that is most comfortable for you. Hold the stand to prevent the monitor from falling when you change its angle. VP229Q/ VP229HE: The recommended adjusting angle is +23 to -5. VA229QSB: The recommended adjusting angle is +359 to -50 (for tilt)/+900 to -900 (for swiveling)/ +130 mm (for height adjustment)/900 (for portrait view). VP229QNP229HE -50-+230 VA229QSB -50-+350 (Tilt) 1800 1800 00 (Swivel) Pivoting the monitor (VA229QSB) 2. 3. 2-4 Lift the monitor to the highest position. Tilt the monitor to its maximum angle. Pivot the monitor to the angle you need. -50-+350 130mm (Height adjustment) Chapter 2: Setup
****** Page 19 ****** It is normal that the monitor slightly shakes while you adjust the viewing angle. 2.4 Connecting the cables Connect the cables as the following instructions: VP229Q/VP229HE VA229QSB To connect the power cord: Connect one end of the power cord securely to the monitor’ AC input port, the other end to a power outlet. To connect the VGA/HDMI/DP cable: a. Plug one end of the VGA/HDMI/DP cable to the monitors VGA/HDMI/ DP jack. b. Connect the other end of the VGA/HDMI/DP cable to your computers VGA/HDMVDP jack. c. Tighten the two screws to secure the VGA connector. To connect the audio cable: connect one end of the audio cable to the monitors line in port, the other end to the computer’s audio-out port. To use the earphone: connect the end with plug type to the monitor’s earphone jack when an HDMI/DP signal is fed. 2-5
****** Page 20 ****** 2-6 To use the USB 2.0 ports (VA229QSB only): Take an USB 2.0 cable, and plug the smaller end (type B) of the USB upstream cable to the monitor’s USB upstream port, and the larger end (type A) to your computer’s USB 2.0 port. Make sure your computer is installed with the lastest Windows 7/Windows 8.1/ Windows 10 operating system. That will enable the USB ports on the monitor to work. When these cables are connected, you can choose the desired signal from the Input Select item in the OSD menu. 2.5 Turning on the monitor Press the power button Q) . See page 1-2 for the location of the power button. The power indicator (b lights up in white to show that the monitor is ON. Chapter 2: Setup
****** Page 21 ****** 3.1 3.1.1 OSD (On-Screen Display) menu How to reconfigure Splendid scenery Mooe Stanoara Mooe Theater Mooe Game “ooe NIgnt Vlew woae Mooe aeac•ng Mooe oarkroom Mode ASUS VAUSQSB Q stanoaro Mooe HOMI x 1030 eoHz 2. 3. 4. 5. Press any button (except the Power button) to display the OSD menu. Press the Menu button to activate the OSD menu. Press the buttons as indicated on the screen to navigate through the functions. Highlight the desired function and press •e to activate it. If the function selected has asub-menu, press Vand A again to navigate through the sub-menu functions. Highlight the desired sub-menu function and press •Z to activate it. Press Vand A to change the settings of the selected function. To exit and save the OSD menu, press or X repeatedly until the OSD menu disappears. To adjust other functions, repeat steps 1-4. 3.102 OSD function introduction 1. Splendid This function contains 8 sub-functions you can select for your preference. Each mode has the Reset selection, allowing you to maintain your setting or return to the preset mode. Splendid scenery Mooe Stanoara Mooe Theater Mooe Game “ooe NIgnt Vlew woae Mooe aeac•ng Mooe oarkroom Mode ASUS VAUSQS8 stanoaro Mooe HOMI x 1030 eoHz ASUS VA229Q/ VP229Q/ VP229HE Series LCD Monitor 3-1
****** Page 22 ****** Scenery Mode: Best choice for scenery photo display with Splendid Video Enhancement. Standard Mode: Best choice for document editing with Splendid Video Enhancement. Standard Mode meets Energy Stare requirements. Theater Mode: Best choice for movies with Splendid Video Enhancement. Game Mode: Best choice for game playing with Splendid Video Enhancement. Night View Mode: Best choice for dark-scene games or movies with Splendid Video Enhancement. sRGB Mode: best choice for viewing photos and graphics from PCs. Reading Mode: This is the best choice for book reading. Darkroom Mode: This is the best choice for a weak ambient light environment. In the Standard mode, the following function(s) are not user-configurable: Saturation, Skin Tone, Sharpness, ASCR. In the sRGB mode, the following function(s) are not user-configurable: Brightness, Contrast, Saturation, Color Temp., Skin Tone, Sharpness, ASCR. In the Reading mode, the following function(s) are not user-configurable: Contrast, Saturation, Color Temp., Skin Tone, Sharpness, ASCR. Eye Care In this function, you can adjust settings to better protect your eyes. 2. 3-2 Eye Care Blue Lignt Filter Rest Remlnoer color Augmentatlon A SUS VA22sasa stenograuooe HOMI 1320 Icec @ Blue Light Filter: In this function, you can adjust the blue light filter from 0 to Max.
****** Page 23 ****** 0: No change. Max: The higher the level, the less blue light is scattered. When blue light filter is activated, the default settings of Standard Mode will be automatically imported. Besides maximum level, the brightness is user-configurable. Maximum is the optimized setting. It is compliance with TUV low blue light certification*. The brightness function is not user configurable. *When color augmentation is in default value (50). Please refer to the following to alleviate eye strains: Users should take some time away from the display if working for long hours. It is advised to take short breaks (at least 5 mins) after around 1 hour of continuous working at the computer. Taking short and frequent breaks is more effective than a single longer break. To minimize eye strain and dryness in your eyes, users should rest the eye periodically by focusing on objects that are far away. Eye exercises can help to reduces eye strain. Repeat these exercises often. If eye strain continues please consult a physician. Eye exercises: (1) Repeating look up and down (2) Slowly roll your eyes (3) Move your eyes diagonal. High energy blue light may lead to eye strain and AMD (Age-Related Macular Degeneration). Blue light filter to reduce 70% (max.) harmful blue light to avoiding CVS (Computer Vision Syndrome) when the user adjusts blue light filter bar to maximum level. Rest Reminder: This function provides you a rest reminder according to how long you set for your working time. For example, if you set a 30-minute working time and there will be a pop up reminder appeared on the upper left corner of the monitor for 5 seconds when time is up. Press any key to make this reminder OSD disappear. When this function is enabled, the following functions are not available: Splendid Demo Mode, GamePlus, QuickFit. Color Augmentation: The adjusting range of color enhancement is from O to 100. This function is not available when sRGB Mode is selected in the Splendid menu. This function is not available when Reddish or Yellowish is selected in the Skin Tone menu. ASUS VA229Q/ VP229Q/ VP229HE Series LCD Monitor 3-3
****** Page 24 ****** 3. 4. 3-4 Color Set a desired color setting from this menu. Color angntness contrast saturauon color Temp. snr Tone A SUS VA22sasa stenograwooe HOMI 1320 Icec @ Brightness: The adjusting range is from 0 to 100. Contrast: The adjusting range is from 0 to 100. Saturation: The adjusting range is from 0 to 100. Color Temp.: Contains 4 modes including Cool, Normal, Warm and User Mode. Skin Tone: contains three color modes including ReddishJ Natural, and Yellowish. Image Set the image related setting from this menu. Image Sharpness Trace Free Aspect control ASCR AMO Freesync wore A SUS VA22sasa stenograwooe HOMI 1320 @ got-•z Sharpness: The adjusting range is from 0 to 100. Trace Free: Adjusts the response time of the monitor. Aspect Control: Adjusts the aspect ratio to fullJ 4:3J or OverScan. 4:3 is only available when input source is in 4:3 format. OverScan is only available for the HDMI input source. VividPixel: Enhances the outline of the displayed picture and generates high-quality images on screen.
****** Page 25 ****** 5. ASCR: Turns on/off the ASCR (ASUS Smart Contræt Ratio) function. AMD FreeSync (DisplayPort and HDMI only): Allows an AMD FreeSync supported* graphics source to dynamically adjust display refresh rate based on typical content frame rates for power efficient, virtually stutter free and low-latency display update. * AMD FreeSync (DisplayPort and HDMI only) can only be activated within 48Hz 75Hz. * For supported GPUSI minimum PC system and driver requirements, please contact the GPU manufactures. Position (Only available for VGA input): adjusts the horizontal position (H-Position) and the vertical position (V-Position) of the image. The adjusting range is from 0 to 100. Focus (Only available for VGA input): reduces Horizonal-line noise and Vertical-line noise of the image by adjusting (Phase) and (Clock) separately. The adjusting range is from 0 to 100. Phase adjusts the phase of the pixel clock signal. With a wrong phase adjustment, the screen shows horizontal disturbances. Clock (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the image is not proportional. Auto Adjust.: Automatically adjusts the image to its optimized positiom clock, and phase (for VGA mode only). Sound Set the sound related settings from this menu. Sound Volume M ute source ASUS VAUSQSB stanoaro Mooe HOMI 1520 x 1030 @ eoHz Volume: the adjusting range is from 0 to 100. Mute: toggles the monitor sound between on and off. Source: decides the monitor sound comes from which source. ASUS VA229Q/ VP229Q/ VP229HE Series LCD Monitor 3-5
****** Page 26 ****** 6. 7. 3-6 Input Select In this function, you can select your desired input source. Input Select VGA HDW System Setup Allows you to adjust the system. System Setup Splendld oemo Mooe Gamepvus au•cRF1t ECO usa Charging OSO setup Language wore A SUS VA22sasa stenograuooe HOMI 1320 Icec @ A SUS VA22sasa stenogrowooe HOMI 1320 Icec @ Splendid Demo Mode: Splits the screen into two for Splendid modes comparison. (Scenery mode only) GamePlus: The GamePlus function provides a toolkit and creates a better gaming environment for users when playing different types of games. The crosshair overlay with different crosshair options lets you choose the one that best suits the game you’re playing. There’s also an onscreen timer you can position on the left of the display so you can keep track of the elapsed gaming time; while the FPS (frames per second) counter lets you know how smooth the game is running. Display Alignment displays alignment lines on 4 sides of the screen, serving as an eæy and handy tool for you to line up multiple monitors perfectly.
****** Page 27 ****** GamePlus Main Menu GamePlus — Crosshair GamePlus — Timer sooo GamePlus Timer — Position n.nm U.UU som 9000 GamePlus Position — FPS Counter QuickFit: You can have a preview of the document or photo layout directly on screen without printing test copies. * Alignment: This facilitates designers and users to organize content and layout on one page and achieve a consistent look and feel. Alignment Grid 1 Alignment Grid 2 A ignment Grid 2 Photo: The various real photo sizes displayed provides photographers and other users to accurately view and edit their photos in real size on the screen. Photo 4×6, 3×5, 2×2 3×5 ECO Mode: reduces power consumption. ASUS VA229Q/ VP229Q/ VP229HE Series LCD Monitor 3-7
****** Page 28 ****** USB charging (VA229QSB only): “On” allows the USB downstream ports to generate a 5V/500mA output when the monitor is turned on or in standby mode. “Off’ a110Æ the USB downstream ports to generate a 5V/500mA output only when the monitor is turned on. OSD setup Adjusts the OSD timeout from 10 to 120 seconds. Enables or disables the DDC/CI function. Adjusts the OSD background from opaque to transparent. Language: There are 21 languages for your selection, including English, French, German, Italian, Spanish, Dutch, Portuguese, Russian, Czech, Croatian, Polish, Romanian, Hungarian, Turkish, Simplified Chinese, Traditional Chinese, Japanese, Korean, Thai, Indonesian, Persian. Key Lock: To disable all function keys. Press the second button from the right over five seconds to cancel the key lock function. Information: Shows the monitor information. Power Indicator: Turns the power LED indicator on/off. Power Key Lock: Enables or disables the power key. All Reset: “Yes” allows you to restore the default settings. Shortcut Defines the functions for Shortcut 1 and 2 buttons. 8. 3-8 Shortcut Shortcut Shortcut 2 A SUS VA22sasa stenograuooe HOMI 1320 Icec @ Shortcut 11Shortcut 2: selects a function for Shortcut 1 and 2 buttons. When a certain function is selected or activated, your shortcut key may not support. Available function choices for shortcut: Blue Light Filter, Splendid, Brightness, Auto Adjust, Contrast, Color Temp., Volume, GamePlusj Rest Reminder, Color Augmentation.
****** Page 29 ****** 3.2 Specifications summary Panel Type Panel size Max. Resolution Pixel pitch Brightness (Typ.) Contrast Ratio (Typ.) Contrast Ratio Max. Viewing angle (HIV) CR>IO Display colors Response time Splendid Video Enhancement Splendid selection Auto adjustment Color tem erature selection Analog input Digital input Earphone jack Audio input Speaker (Built-in) USB 2.0 port Colors Power LED Tilt Pivot Swivel Height Adjustment Kensington lock AC input voltage Power consumption Temperature (Operating) TFT LCD 21.5″ (16:9, 54.62 cm) wide screen 1920 x 1080 0.24795 x 0.24795 mm 250 cd/m2 1 ooo:l (with ASCR on) 16.7 M < 5 ms Yes 8 video preset modes Yes 4 color temperatures D-sub VA229QSB/ VP229Q: HDMI vl .4, DP vl .2 VP229HE: HDMI vl .4 VA229QSB/ VP229Q : Yes VP229HE: No VA229QSB/ VP229Q : Yes VP229HE: No VA229QSB: 2 W x 2 Stereo, RMS VP229Q: 1.5 w x 2 Stereo, RMS VP229HE: No VA229QSB: Upstream x 1 j downstream x 2 VP229Q/ VP229HE: No Black White (On)/Amber (Standby) VA229QSB: -50-+350 VP229Q/ VP229HE: -50-+230 VA229QSB: +900–900 VP229Q/ VP229HE: No VA229QSB: +900–900 VP229Q/ VP229HE: No VA229QSB: 0-130 mm VP229Q/ VP229HE: No Yes AC: 100-240V Power On: < 12 (Typ.)j Standby: < 0.5 W (Typ.)j Power Off: < 0.3 W oec-400c ASUS VA229Q/ VP229Q/ VP229HE Series LCD Monitor 3-9 ****** Page 30 ****** Temperature (N on-operating) Weight (Esti.) Multi-languages Accessories Compliance and Standards VA229QSB: 490 x 423 x 211 mm (with stand, highest) 490 x 312 x 211 mm (with stand, lowest) 490 x 298 x 53 mm (without stand) 590 x 372 x 210 mm (package) VP229Q/ VP229HE: 490 x 363 x 199 mm (with stand) 490 x 298 x 53 mm (without stand) 552 x 420 x 132 mm (package) VA229QSB: 2.6 kg (net without stand); 4.6 kg (net with stand); 6.3 kg (gross) VP229Q: 2.6 kg (net without stand); 3.0 kg (net with stand); 4.4 kg (gross) VP229HE: 2.5 kg (net without stand); 2.9 kg (net with stand); 4.2 kg (gross) 21 languages (English, French, German, Italian, Spanish, Dutch, Portuguese, Russian, Czech, Croatian, Polish, Romanian, Hungarian, Turkish, Simplified Chinese, Traditional Chinese, Japanese, Korean, Thai, Indonesian, Persian) Quick start guide, warranty card, power cord, HDMI cable (optional), DisplayPort cable (optional), VGA cable (optional), USB cable (optional), mini PC kit (optional), cable holder VA229QSB: Energy star, cTUVus, CE, Erp, FCC, RCM BSMI, ROHS, J-MOSSJ ME-PS, WEEE, PSE, Windows 7 & 8.1&10 WHQL, TUV-Flicker free, WV-Low Blue Light, IS09241-307, PC-Recycle, UkrSEPRO, ICES-3, EU Energy Label, TCO, WV-GS, TUV- Ergo, CU, CCC, CELI MEPSJ KC. KCC, E-Standby VN MEPS, PSB VP229Q: Energy star, cTUVus, CB, CE, Erpj FCCj RCM BSMI, ROHS, J-MOSSJ MEPS, WEEE, PSE, Windows 7 & 8.1&10 WHQL, TUV-Flicker free, TUV-Low Blue Light, IS09241-307, PC-Recycle, UkrSEPRO, ICES-3, EU Energy Label, VCCI, TCO, CU, CCC, CELj MEPS, KCj KCCj E-Standby VN MEPSJ PSB VP229HE: Energy star, cTUVus, CB, CE Erp, FCC, RCM BSMI, ROHS, J-MOSS, MEPS, WEEE, PSE, Windows 7 & 8.1&10 WHQL, TUV-Flicker free, TUV-Low Blue Light, IS09241-307, PC-Recycle, UkrSEPRO, ICES-3, EU Energy Label, TCO, CU, CCC, CEL MEPS, E-Standby VN MEPS PSB Taiwan Green Mark 3-10 *Specifications are subject to change without notice. **Measuring a screen brightness of 200 nits without audio/USBlCard reader connection. Chapter 3: OSD (On-Screen Display) menu ****** Page 31 ****** 3.3 Outline dimensions VP229Q/ VP229HE ASUS VA229Q/ VP229Q/ VP229HE Series LCD Monitor 3-11 ****** Page 32 ****** VA229QSB 3-12 ****** Page 33 ****** 3.4 Troubleshooting (FAQ) Problem Power LED is not ON The power LED lights amber and there is no screen image Screen image is too light or dark Screen image is not centered or sized properly Screen image bounces or a wave pattern is • present in the image Screen image has color defects (white does • not look white) Screen image is blurry or fuzzy Possible Solution Press the (b button to check if the monitor is in the ON mode. Check if the power cord is properly connected to the monitor and the power outlet. Check if the power switch is ON. Check if the monitor and the computer are in the ON mode. Make sure the signal cable is properly connected the monitor and the computer. Inspect the signal cable and make sure none of the pins are bent. Connect the computer with another available monitor to check if the computer is properly working. Adjust the Contrast and Brightness settings via OSD. Adjust the H-Position or V-Position settings via OSD. Make sure the signal cable is properly connected to the monitor and the computer. Move electrical devices that may cause electrical interference. Inspect the signal cable and make sure that none of the pins are bent. Perform All Reset via OSD. Adjust the RIG/B color settings or select the Color Temperature via OSD. Adjust the Phase and Clock settings via OSD. ASUS VA229Q/ VP229Q/ VP229HE Series LCD Monitor 3-13 ****** Page 34 ****** 3.5 Supported operating modes Resolution Frequency 640×480 640×480 640×480 640×480 720×400 800×600 800×600 800×600 800×600 1024×768 1024×768 1024×768 1 152×864 1280×720 1280×800 1280×960 1280×1024 1280×1024 1366×768 1440×900 1600×1200 1680M 050 1920×1080 1920x 1080 Horizontal Frequency (KHz) 31.47(N) 35.00(N) 37.86(N) 37.5(N) 31.47(N) 35.16(P) 37.88(P) 48.08(P) 46.88(P) 49.72(P/N) 48.36(N) 56.476(N) 60.02(N) 67.5(P/N) 45.OO(P) 47.7800) 49.7(P) 60.OO(P) 63.98(P) 79.98(P) 47.712(P) 55.94(N) 75.00(P) 65.29(N) 67.5(P) 84.64(N) Vertical Frequency 59.94(N) 66.66(N) 72.81 (N) 75.OO(N) 70.08(P) 56.25(P) 60.32(P) 72.19(P) 75.OO(P) 74.55(P/N) 60.00(N) 70.069(N) 75.03(N) 75.OO(P/N) 60.OO(N) 59.87(N) 60.OO(N) 60.OO(N) 60.02(P) 75.02(P) 59.79(P) 59.89(P) 60.OO(P) 59.95(P) 60.00(P) 74.90(P) Pixel.(MHz) 25.18 30.24 31.5 31.5 28.32 36 40 50 49.5 57.28 65 75 78.75 108 74.25 79.5 83.5 108 108 135 85.5 106.5 162 146.25 148.5 220.75 * "P" I "N" stan& for "Positive" I "Negative" polarity of incoming H-syncN-sync (input timing). 3-14 ****** Page 35 ****** When the monitor is operating in the video mode (i.e., not displaying data), the following high definition modes shall be supported in addition to standard definition video. Pixel Format 720 x 480 1280 x 720 720 x 576 1280 x 720 1920 x 1080 1920 x 1080 Horizontal Frequency Vertical Frequency Pixel Rate (MHz) (kHz) 31.469 45 31.25 37.5 67.5 56.25 60 60 50 50 60 50 27 74.25 27 74.25 148.5 148.5 ASUS VA229Q/ VP229Q/ VP229HE Series LCD Monitor 3-15
FREE ENGLISH PDF
USER GUIDE – USER MANUAL
OWNER GUIDE – OWNER MANUAL
REFERENCE GUIDE – REFERENCE MANUAL
INSTRUCTION GUIDE – INSTRUCTION MANUAL