ASPIRE ODYSSEY MINI (01) PDF Document

The ASPIRE ODYSSEY MINI features the following functionality and parameters:

Wattage Output: The device is a variable wattage device with an operating range of 1.0W to 50.0W in REG mode.

Resistance Parameters: The device can fire coils from 0.1ohm to 3.0ohms in REG mode and in BYPASS mode it can fire coils from 0.2ohm to 3.0ohms. If the resistance is 0.2ohm-1.4ohms in REG mode, the output wattage can reach 50W.

Voltage Output: 0.50V to 8.50V.

Standby discharge current: Less than 120 uA.

Maximum Vaping Time: 12 seconds per puff.

Display: 0.86 inch OLED display.

Battery: Uses one 18650 battery.

Charging: Onboard charging via Micro USB (5V output).

Temperature Control: Viable with Nickel and Titanium coils.

Upon installing the battery, the ASPIRE ODYSSEY MINI will turn on. The screen will display the “aspire” logo for 3 seconds, then the mod will resume control remembering the previous settings.

Clicking the fire button 5 times within 2 seconds will lock the device. Once locked, it will not fire. The screen will display “LOCKED CLICK 5X”. Clicking the fire button 5 times again in 2 seconds will unlock the device.

The mod will enter its sleep mode when left idle for 60 seconds. Pressing the fire button will wake the device, unless the device was locked. If the device was locked, the screen will display “LOCKED CLICK 5X”.

When an atomizer is attached, the display will read “NEW ATOMIZER” followed by options for yes and no. If no is selected, the settings will remain the same as they were previously. If yes is selected, the display will show “Ka Ni Ti”. “Ka” indicates a Kanthal coil, “Ni” indicates a Nickel coil, and “Ti” indicates a Titanium coil.

If “Ka” (Kanthal, standard wattage mode) is selected, the next screen will allow you to switch between Bypass (Direct current from the battery to the atomizer) or Regulated (The current is controlled by the CPU in the device). Wattage may be adjusted via the buttons between the micro USB port and the display. Note that Stainless steel and Nichrome can also be used under the “Ka” settings.

The device delivers from 1 to 50 watts in REG mode. The device calculates the voltage output, up to a maximum of 8.5V, based on the resistance of the atomizer currently installed. If the wattage setting would bring the voltage higher, the device will limit the step down to 8.5V.

If “Ni” or “Ti” (Nickel or Titanium temperature control mode) are selected, you will be prompted to select between “F” (Fahrenheit) or “C” (Celsius). The device will then read “ROOM TEMP”. Selecting “YES” will lock the resistance of your atomizer. Environmental temperatures can impact the resistance of temperature control coils; this feature allows the user to have a consistent vape every time. Selecting “NO” will cause the device to use the old resistance as the baseline for calculating temperatures. Temperature may now be adjusted via the buttons between the micro USB port and the display. Both options will require confirmation upon selection.

When in BYPASS mode, the mod can fire coil resistances as low as 0.2ohm. While in REG mode, the max output wattage for 0.1 to 0.2ohm coils is 30watts.

Pressing the fire button 3 times within 1.5 seconds will cause the screen to shut off. The mod will still work though; users can reactivate the device by pressing the button 3 times within 1.5 seconds or by charging the mod. If the mod is not in standby mode, the screen can be lit up by simply reattaching the tank.

The mod allows for temperatures from 200 to 600 Fahrenheit or 100 to 315 Celsius. The mod can charge through the micro USB port; the max charging current is 800mAh. While charging, the display will show a flashing battery icon. The mod will be fully charged when the cell reaches 4.2V capacity; at such time the battery icon will be full and will not flash. The display will remain lit also though the device is no longer charging. When the cell’s charge falls to 3.9V it will resume charging.

Pressing the buttons between the micro USB and the display will allow the user to increase and decrease the wattage and temperature. Pressing the button longer will change the wattage and temperature faster. Pressing both buttons will cause the display to show the main interface. The display will auto rotate depending on the mod’s orientation.

The ASPIRE ODYSSEY MINI includes the following protective features:

Stepdown protection: When the battery is unable to supply enough amps to fulfill the current wattage setting, the device will decrease the wattage by 10 watt increments. The device will still fire, though at the throttled wattage. If the cell has low power, the wattage will drop directly to 10 watts. Once the wattage is stepped down to 20 or less, the battery icon will flash; pressing the fire button will display “LOW BATTERY”.

Automatic cutoff: After a full 12 seconds of use, the device will stop firing and the display will show “Over 12s” for 3 seconds and then enter standby mode. To begin use again, simply repress the fire button.

High temperature protection: If the control board detects a temperature over 75 degrees Celsius, the mod will cease functioning and display “TOO HOT” for 3 seconds and then enter standby mode. Users may use the device again once it has cooled.

Short circuit protection: If the device detects a short circuit, the device will enter short circuit protection mode and will not fire; instead, the display will read “LOW RESISTOR” for 3 seconds before entering standby mode. To correct the issue, remove your atomizer and check for shorts.

No atomizer detected: When there is no atomizer attached, the display will read “CHECK ATOMIZER” for 3 seconds before entering standby mode.

Low resistance protection: When the device detects a resistance below 0.1 ohm, the display will read “LOW RESISTANCE” for 3 seconds before entering standby mode. The device will no longer fire until the atomizer is replaced with one that is within the device’s operating range.

Reverse battery protection: If the battery is installed reversed, the mod will not functioning, and when plugged in to charge, the OLED display will turn off within 3 seconds.

The kit includes or is compatible with the following coils:

1.8 ohms Clapton coil: With a kanthal base wire and a kanthal wrap, these coils provide more surface area compared to standard coil designs. This results in greater vapor production and a noticeable increase in flavor.

0.15 ohm Ni200: Temperature control coil. For a consistent vape every time.

1.2 ohms kanthal traditional BVC coil: With improved wicking characteristics.

1. Simply twist from the base of the drip tip to set the arrow to the fill setting (note the water drop icon).

2. Simply squirt your favorite juice into the hole. Note: The tank has a 2ML juice capacity.

3. Reset the arrow to the vaping position. Reattach the Triton’s drip tip system and then enjoy. (Note the face exhaling vapor icon).

When using a new atomizer, let the tank stand for 2 minutes so the cotton can be saturated with juice before firing. Do not let the tank become completely empty. Refill the tank to avoid dry burning or damage to the atomizer.

The kit contents include:

1 Complete Triton Mini Tank (1.8ohm clapton coil, pre-installed)

1 temperature control coil (0.15 ohm)

1 replacement atomizer (1.2 ohms)

1 Pegasus Mini

1 Usb chord

1 user manual

1 replacement pyrex glass tube-clear