ARTEVINO OXYVD8WCOUS (01) PDF MANUAL

ARTEVINO OXYVD8WCOUS (01) PDF SUMMARY:

How should I dispose of the packaging after unpacking my wine cabinet?

All packaging used by ARTEVINO is made from recyclable materials (except the expanded polystyrene high density base and the lower hinge protector). After unpacking your cabinet, take the packaging to a refuse collection point. For the most part, it will be recycled.

---

What should I do with my old wine cabinet when replacing it?

When replacing your wine cabinet, enquire at your local municipal refuse department in order to find out the suitable recycling procedure. The refrigerant gases, substances and some parts contained in ARTEVINO wine cabinets are made up of recyclable materials which require a special disposal procedure to be followed. Seal the lock to prevent children accidentally locking themselves inside the cabinet. Disable any unusable appliances by unplugging them and cutting off the power lead.

---

What are the steps for leveling my wine cabinet?

To allow you to easily level your wine cabinet, it is fitted with 2 adjustable feet at the front. Carry out final leveling of your cabinet (spirit level recommended).

---

How long should I wait before plugging in my wine cabinet?

WAIT 48 HOURS BEFORE PLUGGING IN YOUR APPLIANCE.

---

What is the maximum degree I can tilt my cabinet when moving it?

When moving your cabinet, never tilt it more than 45°, and always on its side (on the opposite side of the flexible lead).

---

What should I check when unpacking my cabinet?

When unpacking your cabinet, check that it is not damaged (signs of impact, buckling, marks). Remove the protective elements found inside and outside your cabinet including the lower hinge protector. Fit the cap, found in the accessories bag, used for sealing the hole in the lower hinge.

---

What should I check after opening the door of the wine cabinet?

Open the door and check that the various elements are intact. Arrange the electric power lead so that it does not come into contact with any of the cabinet’s components.

---

How should I install the rear spacer?

Install the rear spacer at the back of the cabinet. This allows a space of 7 cm to be maintained between the wall and the rear of the cabinet. This space allows your cabinet’s power consumption to be optimized. Place the 2 caps in the 2 holes at the top of the cabinet, ensuring that you do not push them all the way in. Slide the rear spacer between the caps and the wall of the cabinet, then push the 2 caps all the way in.

---

Where should I place my wine cabinet?

The location that you choose for your cabinet must:

• Be open to the outside and well ventilated (not in an enclosed cupboard, for example).
• Allow there to be a minimum space of 7 cm between the wall and the back of the cabinet.
• Not be close to any source of heat.
• Not be too damp (utility room, laundry room, bathroom…).
• Have a flat, stable floor.
• Be supplied with standard accessible power (outlet that complies with standards in force in your country, earthed with circuit breaker).

---

Is it okay to use an extension cord or adaptor?

It is forbidden to use an extension cord or adaptor.

---

What should I do when placing two cabinets side by side?

If you are placing two cabinets side by side, ensure that you leave a gap of one to two cm between each cabinet.

---

How do I change the direction in which the door opens?

Follow the instructions below (example for changing a right-hand door into a left-hand door):

1. Unscrew the three screws using a “T25” Torx wrench.
2. Remove the upper hinge.
3. Carefully remove the caps using a thin blade.
4. Remove the cabinet door by opening it slightly, then lifting it upwards.
5. Unscrew the door pin.
6. Carefully remove the cap using a thin blade and assemble the pin in its place. Reposition the cap on the opposite side.
7. Unscrew the two screws and the door catch.
8. Unscrew the two screws on the opposite side and remove the two washers.
9. Turn the door through 180°. Warning: the door is very heavy. Take any necessary precautions to ensure that you do not injure yourself or drop it.
10. Put the door back on its pin.
11. Mount the door catch on the desired opening side, using screws.
12. Replace the washers, then the screws, on the side opposite the door catch.
13. Put in place the upper hinge.
14. Screw the hinge so that the door is completely parallel to the cabinet. Check that the door seal adheres well to the cabinet (by closing the door), to ensure that it is completely air-tight.
15. Put in place the caps.

---

What are the steps for installing a shelf in storage version?

1. Insert 2 runners in the shelf support strips. For each shelf, position one runner on the right and one runner on the left. Ensure that the runners are correctly fixed in their housing.
2. Place the shelf in the 2 runners.
3. Place a locking dowel in each of the 2 holes located at the front of the shelf, in the upper section. These pins then fix the shelf with respect to the runner and prevent any unwanted movement.
4. Start by placing bottles in each recess of the back row with the base of the bottle towards the back.
5. Continue by placing the bottles in the opposite direction on the front row.
6. Continue stacking the bottles, ensuring that no bottles touch the back wall.
7. A storage shelf can support a maximum of 6 rows of 12 bottles, i.e.72 traditional Bordeaux bottles.

---

How do I install a shelf in display version?

1. Insert 2 runners in the shelf support strips. For each shelf, position one runner on the right and one runner on the left.
2. Place the shelf in the 2 runners.
3. Place a locking dowel in each of the 2 holes located at the front of the shelf, in the upper section. These pins then fix the shelf with respect to the runner and prevent any unwanted movement.
4. Start by placing bottles in each recess of the back row with the base of the bottle towards the back (6 traditional Bordeaux bottles).
5. Continue stacking the bottles on the back row (6+6+6+6 = 24 traditional Bordeaux bottles), ensuring that no bottles touch the back wall.
6. To display your bottles, place them vertically at the front of the shelf (maximum capacity: 6 traditional Bordeaux bottles).
7. In display version, the shelf has a maximum capacity of 30 traditional Bordeaux bottles.

---

How do I install a shelf in sliding version?

1. Insert 2 runners in the shelf support strips. For each shelf, position one runner on the right and one runner on the left.
2. Place the shelf in the 2 runners.
3. Place a locking dowel in each of the two holes located at the back of the shelf, in the upper section. These pins prevent the shelf from sliding all the way out of the cabinet.
4. Start by placing bottles in each recess of the back row with the base of the bottle towards the back.
5. Continue by placing the bottles in the opposite direction on the front row.
6. A sliding shelf can only hold a single row of bottles (maximum of 12 traditional Bordeaux bottles).
7. In the case of a mixed layout, for optimal accessibility, it is recommended that you place the sliding shelves in the central section of the appliance.

---

How many loaded sliding shelves should I pull out at a time?

NEVER PULL OUT MORE THAN ONE LOADED SLIDING SHELF AT A TIME.

---

How should I load my wine cabinet if I don’t have enough bottles to fill it?

If you do not have enough bottles to fill your wine cabinet, it is preferable to spread the load over the entire cabinet rather than placing bottles “all at the top” or “all at the bottom”. For optimal performance, it is recommended that you use the cabinet at over 75% of its capacity.

---

How do I install the specific grid for beverages (only available on the 2 temperatures model – OXY2TVD6COUS)?

1. Place a universal ArteVino shelf in the beverage center.
2. Place the grid on the ArteVino shelf.
3. Install your bottles and cans upright on the grid.

---

What should I do when commissioning my cabinet?

After waiting 48 hours, plug in your wine cabinet, having checked that your socket is correctly supplied with power (presence of correct sized fuses, circuit breaker in working order). If need be, plug in another electrical appliance to check the power supply.

---

What does the temperature display show?

Temperature display: displays the actual temperature inside your wine cabinet. It is therefore necessary to wait before your new setting takes effect.

---

How do I see the temperature setting?

Simply press and hold down SET for a few seconds to see the temperature setting.

---

What are the functions of the buttons on the control panel?

Buttons ( / / SET): allow you to select the desired temperature inside the cabinet.

---

What is the function of the Standby button?

Standby button ( ): allows you to switch the cabinet on and put it on standby.

---

What does the Compressor status light indicate?

Compressor 1: indicates that the compressor is operating. When this flashes, it means that the compressor is going to start up in a few minutes (technical delay).

---

What does the Defrosting cycle status light indicate?

Defrosting cycle 2 : indicates that an automatic defrosting cycle is underway.

---

What does the Heater status light indicate?

Heater 3 : indicates that the heater is operating.

---

What does the Alarm status light indicate?

Alarm 4 : informs you that there is an abnormally high or low temperature inside the wine cabinet.

---

How do I switch on the cabinet?

By default, the control is in the OFF position. To switch on the cabinet, press and hold the ( ) button for several seconds until just the temperature is displayed.

---

How do I put the cabinet on standby?

To put the cabinet on standby, press and hold down the ( ) button for several seconds. The display switches between the internal temperature and the OFF display (the cabinet is no longer operating, only the display is active).

---

How do I reactivate the cabinet back on?

To reactivate the cabinet back on, press and hold down the ( ) button for several seconds until just the temperature is displayed.

---

How do I set the temperature of my wine cabinet for 1 temperature models (OXYVD8WCOUS / OXYVG8WCOUS)?

1. Press and hold down the SET button for a few seconds until the temperature setting (ST1) flashes.
2. Set the desired temperature using the and buttons.
3. Confirm your programming by pressing the SET button. If you do not confirm your setting with this key, your modification will not be registered. The recommended setting range for aging wine is 50°F – 57°F. The default setting is 54 °F. However, the temperature may also be set between 48°F and 59°F. Your wine cabinet can be placed in a room with a temperature of 32°F – 86°F.

---

How do I set the temperature of my wine cabinet for 2 temperatures model (OXY2TVD6COUS)? Beverage center compartment (bottom):

1. Press and hold the SET button for a few seconds until the SET temperature (ST1) flashes. The default temperature setting is 38°F. However, the temperature can be set from 38°F to 43°F.
2. Set the desired temperature using the and buttons.
3. Maintain pressure on the SET button for a few seconds. This confirms the temperature setting of the lower compartment of the cabinet (Beverage center) and allows you to access the temperature setting (ST2) of the upper compartment (aging compartment).

Aging compartment (top):

1. The default temperature is 54°F. However, the temperature can be set from 50°F to 57°F.
2. Set the desired temperature using the and buttons.
3. Confirm your setting by pressing the SET button. If you do not confirm by pressing this key, the change in temperature setting will not take effect. Your wine cabinet can be placed in a room with a temperature of 54°F – 86°F.

---

What should I do if the alarm warning light appears?

In case of significant difference between the temperature inside the cabinet and the temperature setting, for over 3 hours, the control activates the alarm and the warning light appears. If you have loaded your cabinet with a large number of bottles, it can take several hours for your wine cabinet’s temperature to stabilize. The warning light may then appear. Wait a while then check again. If the alarm warning light does not disappear, contact your retailer.

---

What should I do if the temperature does not stabilize after commissioning or significant changes to the temperature setting?

When commissioning your cabinet, or after significant changes to the temperature setting, it can take several hours for your wine cabinet to stabilize and display the new desired temperature. Wait a few days. If the temperature does not stabilize, contact your retailer.

---

What are the regular maintenance operations for my wine cabinet?

1. Clean the water drain at the bottom of the wine cabinet. Pay attention that nothing is blocking this drain.
2. Regularly vacuum (twice a year) the condenser (black metal grill attached to the back of your wine cabinet).
3. Once a year, thoroughly clean the inside of your wine cabinet, remembering to unplug it after removing your bottles (use a gentle cleaning product and water and remember to rinse well and then dry it with a soft rag).
4. It is often necessary to clean the door seal. Using unsuitable cleaning products can cause premature aging of the seals. Certain rules must therefore be followed: whenever you clean the seal, always rinse off any cleaning product with clear water. All traces of cleaning product must be removed from the seal. ARTEVINO only recommends using a mild soapy solution. If this proves insufficient, it is possible to occasionally use an ethanol-based solution, provided that the concentration used is less than 10% and that the seal is then rinsed thoroughly with clear water.

---

How do I activate the humidity process for one temperature model wine cabinet?

When installing your cabinet, it is important to pour the equivalent of one glass of water onto the floor of the cabinet to activate the humidity process.

---

What should I do if the compressor does not work?

Check that the wall socket is supplied with power by plugging in another electrical appliance.

---

What should I do if the compressor never stops?

Put your hand on the condenser (grill located on the back of the appliance). If the condenser is cold, contact your retailer. If the condenser is hot, set your cabinet (ST1) to the maximum temperature setting value. If the compressor still does not stop, contact your retailer.

---

What should I do if the wine cabinet does not switch on?

Contact your dealer.

---

What are the temperature ranges for the wine cabinets?

1 temperature models OXYVD8WCOUS / OXYVG8WCOUS:

• Recommended T° range: 32°F – 86°F.

2 temperatures model OXY2TVD6COUS:

• Recommended T° range: 54°F – 86°F.

---

What is the climate class for all models?

Climate class: our appliances are designed to be used at an ambient temperature of 50°F – 90°F – Class SN. Nevertheless, refer to the table of technical features to find out the optimal performance for your product.