ANKO CL-2001-22.2V-A (01) PDF DOCUMENT

Please read the instruction manual carefully before first use and keep it for future reference.

This appliance is not for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.

Children should be supervised to ensure they do not play with the appliance.

To protect against electric shock, do not immerse the appliance, charging cord or plug in water or other liquids.

For electrical safety, any repairs must be performed by a qualified electrical person only, or the product must be disposed of.

DO NOT misuse the Charger Cable. Grasp the charger body to disconnect.

DO NOT use with a damaged charger cable or body.

The charger/plug must be removed from the socket-outlet before cleaning or maintenance.

DO NOT handle the charger or appliance with wet hands.

DO NOT use without the filter in place.

DO keep hair, loose clothing, and body parts away from openings or moving parts like the Rotary Cleaning Brush.

DO disconnect the Charger from the power supply when not in use for extended periods.

ONLY for domestic use. Industrial or commercial use invalidates the warranty.

DO NOT use to clean up flammable, combustible, or toxic materials.

DO NOT use the product without the water tanks in place.

DO NOT charge with an external timer or remote-control system.

DO NOT use if the appliance has been dropped, damaged, or malfunctions.

DO use only on indoor surfaces.

DO store your appliance indoors in a cool, dry area.

DO operate the Charger from a power source of the same voltage, frequency, and rating as indicated on the product identification plate.

Only use the Battery Charger supplied with this appliance.

DO ensure the appliance is switched off before handling or picking up.

IMPORTANT: Only use a hard floor cleaning solution and always follow the instructions on the solution bottle.

For the purposes of recharging the battery, only use the detachable supply unit provided with this appliance.

Charger Model No.: ZD12D260050AU 100-240V~ 50-60Hz 0.5A Output: 26V — 500mA

Battery Pack Specification: Type: Li-ion, 18650 22.2Vd.c., 2200mAh

The Appliance must only be supplied at Safety Extra Low Voltage “SELV”.

Only charge the battery between an ambient room temperature of 10°C – 40°C.

Consumers are cautioned against using and/or purchasing counterfeit and/or inferior quality batteries as they have the potential to cause fire, personal injury, and/or damage to property.

Never try to recharge Non-Rechargeable batteries.

The battery may explode if disposed of in fire.

To prevent injury or burns, do not allow metal objects to contact battery terminals.

Do not use or store in temperatures above 40°C.

Do not expose the appliance or battery to excessive temperatures.

This appliance contains non-replaceable batteries. As the Battery Pack is not removable, the whole unit will need to be handed in for the battery to be recycled.

WARNING: With any battery type, should a metal object come into contact with battery terminals either while charging or not charging, this will short out the battery and could cause the battery and surrounding items to catch fire.

Do Not Open the Appliance to access the battery Pack. There are no serviceable parts inside.

This product is only designed for cleaning hard smooth surfaces and not carpeted or rough surfaces.

DO NOT add any other agents into the water tank, such as, rust removers, odour counter reacting agents, alcohol, solvents, strong acidic or strong alkali formulas or any type of cleaning solution not specifically for use in this type of cleaning appliance as this may cause serious injury to the user and may damage the appliance and floor surface.

IMPORTANT: Only use a hard floor cleaning solution.

Always follow the instructions on the Cleaning Solution Bottle.

Important: Only mix the ratio of cleaning solution to water as instructed on the cleaning solution bottle. Do Not add more cleaning solution than that specified on the cleaning solution container.

1. Handle Location Hole

2. Cleaning Solution / Water Tank

3. Main Unit

4. Display Panel

5. Dirty Water Collection Tank

6. Self-Clean Storage Base

7. Floor Head

8. Handle

9. Battery Charger ZD12D260050AU

10. Control Panel

No tools are required to assemble the handle to the main unit.

1. Set the Appliance in an upright position.

2. Align the handle over the hole in the top of the main unit then push down firmly until the handle locks in place.

NEVER LEAVE THE APPLIANCE UNATTENDED WHEN CHARGING.

NOTE: The Appliance must be fully charged prior to first use. Normal charging time will take approx. 4 – 5 hours.

1. To charge the battery, insert the small round plug of the battery charger into the charging socket located on the side of the main unit.

2. Plug the body of the battery charger in the power point and switch on.

3. The indicator lights in the front window will indicate when the battery is charging. There are three blue light segments that will “roll” bottom to top indicating charging.

4. As the battery charges to approximately 33%, the first segment light will turn permanently on. At approximately 66%, the second light segment will turn permanently on. When the battery reaches 100%, the third light segment will turn on permanently.

5. At this time, turn off and remove the battery charger from the appliance and the power point. Note: All lights will turn off after some time if not unplugged immediately.

DO NOT leave the unit charging when the battery is full.

The appliance cannot be used during charging.

IMPORTANT: Using the Appliance as a dry vacuum will damage the Rotary Brush and the appliance.

1. Remove as much furniture as possible.

2. Thoroughly vacuum the floor to be cleaned with a regular vacuum cleaner.

1. Switch off the Appliance and remove the battery charger if on charge.

2. Remove the Cleaning Solution / Water Tank by pressing down on the top of the tank, pull forward and lift out.

3. Unscrew the cap (anticlockwise) and remove.

4. Following the instructions on the cleaning solution bottle, add the cleaning solution and warm tap water (max. 40°C) to the Cleaning Solution / Water Tank.

5. To work out how much cleaning solution to add to the clean water tank, follow this equation:

For example: If the cleaning solution instructions state to mix 1:15, this means 1 part cleaning solution to 15 parts water.

The water tank holds a maximum of 650ml therefore, we need to determine what 1 part of cleaning solution will be.

1 part = (650ml ÷ 15) = 43.3ml

Therefore, add 43ml of cleaning solution to the clean water tank first, and then fill the rest of the way with warm tap water (max. 40°C).

IMPORTANT: Ensure the cleaning solution to warm water ratio is correct as per the instructions.

6. Replace the Cleaning Solution / Water Tank Cap and tighten clockwise. Do not over tighten.

7. Replace the Cleaning Solution / Water Tank back into position as shown and push it in firmly until it clicks in place.

Before cleaning, determine where to start and stop, making sure you will not walk over the previously cleaned areas.

Using the Cleaner:

1. Place your foot on the floor head to hold it down, and at the same time pull the handle backward to unlatch it from the parking position and into the cleaning position.

2. Press the On/Off button on the handle to turn the appliance on. The cleaner will start on the Low water dispensing level by default.

3. Push and pull the appliance back and forward slowly, as if you were vacuuming a carpet.

4. To turn off, press and release the On/Off button again. The motor will momentarily speed up to suck up remaining water before turning off.

5. When you have finished cleaning, push the handle forward until it is positioned upright and locked into place.

Tips for Floor Cleaning:

Use a steady, moderate, forwards and backwards motion.

Do not make the floor too wet.

Wipe any cleaning solution from woodwork and furniture to prevent any damage.

Water Dispensing Indicator:

With the appliance switched on, it will be in the default Low Water Dispensing Level (White indicator light). To change to a higher quantity of water, press and release the Water button. The White indicator light will change to Red colour. To change back to the Low setting, press and release the Water button again.

Battery Level Indicator:

During use, the Green indicator lights in the front window will indicate the remaining battery charge level.

As the battery charge capacity drops to approximately 66%, the first segment light will turn off leaving only two lights. When the battery drops to approximately 33%, the second light segment will turn off leaving on one light. As the battery continues to drop to 0%, the third light segment will flash briefly before the unit and indicator light will turn off. The battery will need to be fully recharged before using again.

Always switch off the appliance before emptying the tank.

Note: An automatic shut-off device (Water Float) will turn the appliance off when the tank is full.

1. Switch off the Appliance.

2. To remove the Dirty Water Collection Tank, slide the latch located on the back of the tank down to unlatch and then swing the tank backward and lift out.

3. Take the tank to your sink to empty out.

4. Remove the filter by grasping the filter frame and pulling straight out. Place the filter aside for washing.

5. Open the Dirty Water Collection Tank by grasping the top section and pulling straight up and off.

6. Empty the dirty water out of the collection tank and rinse out with fresh clean water.

7. Rinse the top section and its components in clean fresh warm water (max. 40°C), ensuring the water float is free to move up and down, and then refit it to the Dirty Water Collection Tank.

8. At this time, you should clean the filter. Refer to the “Cleaning the Filter” instructions.

Important: Remember to refit the filter before next use.

IMPORTANT: The Filter must be cleaned regularly for best performance. Never use the appliance without the filter fitted.

1. Remove the filter from the Dirty Water Collection Tank as described in the emptying instructions.

2. Open the filter cage and remove the foam filter.

3. Rinse the filter with warm water (max. 40°C) and allow the filter to thoroughly dry before next use. DO NOT scrub, wring, or place the filter in a dishwasher. Do not use a hair dryer to dry the filter.

4. Refit the Foam Filter back in its cage and close the cage.

5. Place the filter in the Self-Clean Storage Base to let it air dry. This helps prevent mold issues.

DO NOT forget to refit the filter before next use.

IMPORTANT: Never use the appliance without the Rotary Brush or the Rotary Brush Cover fitted.

1. Ensure the appliance is turned off.

2. On the top of the floor head, slide the latch at the rear of the Rotary Brush Cover forward and then swing the cover up and forward, then lift off.

3. Grasp the end of the rotary brush with the location bearing, and pull straight up, then lift the rotary brush out.

4. Rinse the Rotary Brush with warm water (max. 40°C) and then allow it to dry thoroughly. DO NOT scrub, wring, use a hair dryer, or place it in a dishwasher.

5. Place the Rotary Brush in the Self-Clean Storage Base to let it air dry to prevent mold issues.

6. At the same time, clean the rotary brush cover and the rotary brush recess in the floor head with mild detergent and lukewarm water, then rinse off and dry with a cloth.

7. Before next use, refit the rotary brush and the cover. DO NOT forget to refit the Rotary Brush before next use.

1. First, empty the Dirty Water Collection Tank and refill the Clean Water / Solution tank with 40°C clean water. (Cleaning Solution is not required).

2. Ensure the Battery is charged or has enough charge for at least 10 minutes.

3. Place the Self-Clean Storage Base on the floor and place the Floor Cleaner in the base.

4. Press and hold the Self Clean button on the handle for approximately 2 seconds until the unit starts.

5. Allow the unit to run through its self-clean cycle. The appliance will turn off when the cycle has completed. You can stop this function earlier by pressing the On/Off button.

6. Once completed, empty the Dirty Water Collection Tank and clean the filter, allowing it to dry.

7. Empty any remaining water left in the Clean Water Tank.

8. Next, clean the Rotary Brush and the floor head as described under the section “Cleaning the Rotary Brush and Cover”.

CAUTION: DO NOT IMMERSE APPLIANCE IN WATER OR LIQUID, OR RINSE UNDER A TAP OR WITH A HOSE.

1. Ensure the appliance is turned off.

2. Never use abrasive cleaners, solvents, steel wool, scouring pads, or sharp utensils to clean.

3. Clean the outside of the appliance with a damp (not wet) cloth with mild detergent and wipe over the surfaces.

4. Dry thoroughly with a clean cloth.

5. DO NOT place any components in a dishwasher.

1. After you have finished using the Appliance, switch it off.

2. Do not store the product with cleaning solution in the water solution tank or dirty water in the Dirty Water Collection Tank, as mineral deposits and mildew can form.

3. Thoroughly clean the appliance as described previously.

4. Store the filter and rotary brush outside of the appliance in the dedicated storage holder in the Self-Clean Storage Base so that they can dry.

5. Recharge the battery and remove the charger once the battery is fully charged.

6. When not in use, store your appliance and all its accessories and instruction manual in a safe and dry place.

Cause	Remedy
Dirty Water Collection Tank is full	Empty out Tank
Rotary Floor Brush is jammed	Remove items from the rotary floor brush causing the jam
Battery is not charged	Charge the battery 4 – 5 hours
Battery charger is plugged into the appliance.	Remove the battery charger from the appliance.

Cause	Remedy
No Power to the power point or not switched on.	Check with another appliance to ensure there is power being supplied from the power point.
Faulty Battery Charger	Contact Customer Service.

Cause	Remedy
The wrong Battery Charger is being used.	Only use the battery charger supplied with this appliance. Refer to section “IMPORTANT SAFEGUARDS” for battery charger model and specifications.

Cause	Remedy
Battery Charge too low	Charge the battery 4 – 5 hours

Cause	Remedy
Dirty Water Collection Tank is full	Empty out Tank
Battery has been depleted	Recharge the battery 4 – 5 hours
Rotary Brush is jammed	Remove items from the rotary brush causing the jam

Cause	Remedy
The suction nozzle behind the rotary brush is blocked	Remove any blockages
Hair or other debris is wrapped around the Rotary Brush	Remove items from the rotary brush

Cause	Remedy
No Water / Solution in Clean Water Tank	Fill Water tank with the correct amount of water and cleaning solution.
Clean Water Tank not fitted, or fitted correctly	Ensure the Water Tank is fitted correctly

Cause	Remedy
Rotary Floor Head is missing	Fit Rotary Floor Head to appliance before use.
Filter in the top of the Dirty Water Collection Tank is missing	Fit the Filter into the top of the Dirty Water Collection Tank
The filter and screen is dirty / blocked	Clean the filter and filter screen
Dirty Water Collection Tank not fitted correctly	Ensure the Dirty Water Collection Tank is fitted to the appliance correctly
Hair or other debris is wrapped around the Rotary Brush	Remove items from the rotary brush
The cover over the rotary brush on the top of the floor head is not installed correctly	Ensure the cover over the rotary brush on the top of the floor head is installed correctly.
The suction nozzle behind the rotary brush is blocked	Remove any blockages

Cause	Remedy
High Water setting has been selected (Red Indicator Light)	Press the middle (Water Dispensing Level) button to reduce amount of water being dispensed. (White Indicator Light)
Appliance has been used over the same spot too many times.	Keep the appliance moving across the floor without moving too quick.
Filter in the top of the Dirty Water Collection Tank is missing	Fit the Filter into the top of the Dirty Water Collection Tank
Rotary Floor Head is missing	Fit Rotary Floor Head to appliance
Dirty Water Collection Tank not fitted correctly	Ensure the Dirty Water Collection Tank is fitted to the appliance correctly

Cause	Remedy
Button not pressed long enough	Press and hold the button for a minimum of 2 seconds until the self-clean function starts.

If all the above checks out and still the unit will not turn on at all, it could be the internal temperature safety fuse which has activated. If this occurs, call our customer service department for further instruction.