ANKO 42990369 (01) PDF MANUAL

ANKO 42990369 (01) PDF SUMMARY:

How do I measure my heart rate?

Press and hold the touch button for two seconds to begin measuring heart rate. The device will automatically stop after one minute, record the last value, and display it on the main interface. It will then distinguish between high and low heart rates based on the last measured value.

---

What should I do to ensure an accurate heart rate measurement?

The heart rate sensor should be in close contact with the skin. The smart watch should not be too loose, as this will result in an inaccurate measurement. Do not look at the green light of the sensor. Stay still while measuring heart rate. Movement can delay measurement or result in no data. Do not move until the value is measured. If there is a big difference in measured data, rest before measuring heart rate again. The average value obtained through five consecutive measurements is more accurate. Make sure there is no dirt on the bottom of the heart rate sensor during measurement. Skin color, hair density, tattoos, and scars may affect the accuracy of the measured results, in which case it is necessary to remeasure the heart rate.

---

Is this device a medical-grade device?

No, the anko Bluetooth Smart Watch is not a medical-grade device. It is a fitness tracker and a general wellness device used to track exercise activity. It does not make any medical claims and is not a suitable replacement for a medical device. Consult a doctor for diagnostic purposes and to track a serious medical condition.

---

What are the safety instructions I should follow when using this device?

• Do not open the device, as this will void the warranty and may pose a safety hazard.
• This device is not intended for use by people with reduced physical, sensory, or mental abilities, or lack of experience/knowledge, unless supervised or instructed.
• The product is not a toy; do not allow children or pets to play with it.
• Do not drop the device or subject it to heavy blows.
• The device contains electrical components that pose a risk of injury if handled improperly.
• Do not expose the device to extreme temperatures, steam, or hot water.
• The device is waterproof.
• The fitness tracker can be worn in the rain and in the shower but is not suitable for diving or immersing in water for over 30 minutes.
• Do not check any messages or data on the device while operating a vehicle or in other situations where distraction could pose a safety hazard.
• Maps, directions, and other GPS or navigation data may be unavailable, inexact, or incomplete.
• The product is not a medical instrument and is not suitable for diagnosis, treatment, or prevention of illness.
• The heart rate and VO2 values calculated by the device are intended as a reference only and should not be used for medical diagnosis, self-diagnosis, or as a base for treatment.
• If you have a circulatory or blood pressure disorder, exercise under medical supervision.
• Prolonged contact with the wristband can cause skin irritations or allergies. If you notice any signs of skin irritation, stop using the product or wear it over clothing. If symptoms persist, consult your physician.
• Consult your physician before beginning or changing your exercise program.
• If you are in a health risk group and the use of the product may impair your condition, consult your physician before use.
• Keep all packaging material away from children due to the risk of suffocation. Dispose of packaging appropriately.
• The product contains small parts that pose a suffocation hazard and is suitable exclusively for personal use.

---

How do I use the sports mode?

In the sports mode, hold the touch button for two seconds to enter. There are eight sport options: walking, running, cycling, rope skipping, badminton, basketball, football, and swimming. If you choose “walking,” it will start recording sport parameters. To exit, press and hold the touch button for two seconds and select “pause,” “exit,” or “return”.

---

How do I measure blood pressure?

Click the touch button to switch to the blood pressure interface. Press and hold the blood pressure interface for 2 seconds to start measurement. After measurement, the smart watch will vibrate and display the blood pressure data. Measure in a quiet place with appropriate temperature. Rest for at least 10 minutes before measurement to avoid tension, anxiety, and emotional excitement. Measure blood pressure three times, with two minutes apart each time, and record the average of the three readings.

---

How do I measure blood oxygen?

Click the touch button to switch to the blood oxygen measurement interface. Press and hold the blood oxygen interface for 2 seconds; it will display “loading.” After measurement, the smart watch will vibrate once and display the blood oxygen data.

---

Are the blood pressure and blood oxygen data accurate?

The data of blood pressure and oxygen are for reference only and cannot be used as the basis of medical-related decisions.

---

How does the weather information work?

The weather page shows the current weather, air quality, and weather forecast. Weather information is available after connecting to the app, and the information will not update if disconnected from the smart watch.

---

How do I view messages on the device?

Switch to the Message interface to enter the information content. Press and hold the touch button for 2 seconds, then click the touch button to switch to the next message. It displays messages pushed from short messages and chat software. Up to five messages can be saved, and new messages replace old ones. To delete a single message, enter the message content interface and hold the touch button for 2 seconds.

---

How do I activate the fitness tracker?

Press and hold the touch button for 5 seconds or charge the smart watch. Press and hold the touch control for at least 3 seconds. The device will switch on and enter activity mode. It displays the day, date, battery charge indicator, time, and last activity (km, steps, kcal).

---

How do I download the app?

Scan the QR code with a mobile phone to download the app or search for “PubuFit” in the Google Play or Apple App Store and download it.

---

How do I use the music control?

When connected to a mobile phone, the smart watch can control the music player. You can use the smart watch to control play/pause, the previous song, and the next song.

---

How do I use the photo control?

When connected to a mobile phone, the smart watch can be used as a remote control for the mobile camera. After opening the “Photo Control” in the app, you can shake the smart watch and hold the touch button to take photos.

---

How do I enter the settings menu?

Press and hold the “Settings” interface to enter the functional interface.

---

How do I adjust the brightness?

Press and hold the touch button for 2 seconds to enter “brightness regulation,” click the touch key to select brightness, and press the side key to return.

---

How do I use the stopwatch?

Press and hold the stopwatch page to “start” timing, click once to “pause” timing, and hold it to “stop” timing.

---

How do I mute the device?

The mute function is closed by default. To open or close the mute function, press and hold the touch button for two seconds.

---

How do I restore the factory settings?

Press and hold the touch button for over 3 seconds to clear all messages in the Smartwatch and restore the factory settings.

---

How do I power off the device?

Press and hold the touch button for 3 seconds, and the device will power off.

---

How do I connect to the app?

Ensure your smartphone’s Bluetooth function is activated. Connect to the app before using your fitness watch for the first time by following the app instructions. Your mobile phone must support Android 5.1 or iOS 8.0 or above, and Bluetooth 4.0 or above. For Android, the device is connected directly from system settings. For iOS, the device is connected from device settings in the app. Select the device “KM42990369” in the device list.

---

How do I disconnect from the app?

For Android, disconnect from the phone by clicking on “Remove Device” from the app. For iOS, click setup Bluetooth, click on the “!” symbol on the right, and choose to ignore the device.

---

Why does the smart watch automatically disconnect Bluetooth when the Android screen goes out?

1. Lock background app. When the PubuFit process is cleared, the smart watch will be disconnected from the phone.
2. Set app to self-startup.
3. Unrestricted background operation. With the app installed on an Android mobile phone, the background operation is restricted intelligently by default. The app should be set manually without any restrictions.

---

Why can’t the smart watch receive messages?

1. Ensure the push message is switched on in the app settings.
2. Ensure that the message can be displayed normally in the mobile phone notification bar. The message push on the smart watch is completed by reading the message from the mobile phone notification bar. The smart watch will not receive the push message if there is no message in the mobile phone notification bar. You need to find notification settings in the mobile phone settings and turn on the notification switch of WeChat, QQ, phone, SMS, and mobile phone client.

---

What are the main interface functions?

Once paired with the app for the first time, it will synchronize the time, date, steps, and calorie symbols of the phone.

---

How does the step counter work?

The step-counting interface shows steps. With the smart watch on your wrist, it can count steps, distance, and calories automatically.

---

How does the sleep monitoring work?

When worn at night, the smart watch automatically determines if the user is sleeping, records deep and shallow sleep separately, and summarizes sleeping time to help users monitor sleep quality. It measures sleep quality by the range and frequency of wrist movements as you sleep. Note that sleep monitoring time is for reference only.

---

What is the warranty for this product?

This product has a 12-month warranty from the date of purchase, provided it is used in accordance with the accompanying instructions. This warranty is in addition to your rights under the Australian Consumer Law. Kmart will provide a refund, repair, or exchange for defective products within the warranty period. This warranty does not apply if the defect is a result of alteration, accident, misuse, abuse, or neglect. Retain your receipt as proof of purchase. Contact the Customer Service Centre on 1800 124 125 (Australia) or 0800 945 995 (New Zealand) or via Customer Help at Kmart.com.au for any difficulties. Warranty claims can be addressed to the Customer Service Centre at 690 Springvale Rd, Mulgrave Vic 3170.