AMETEK CRYSTAL XP2I-DP (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD AMETEK CRYSTAL XP2I-DP (01) PDF MANUAL


PDF Content Summary: XP2i Operation Manual for XP2i-DP Digital Test Gauge

Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pressure Ranges, Display Scales, and Resolution . . . . . . . . . . . . . . . . . . . . . . . . . 5 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Differential Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Continuous Vacuum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Safety & Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Hazardous Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Contact Us . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Factory Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Overview ⚫ 1 Overview ④   INTRODUCTION Thank you for choosing the XP2i-DP Digital Test Gauge from Crystal Engineering Corporation. The XP2i-DP is a combination of leading edge technology, double-sided isolated differential pressure sensing, and rugged industrial design. Based on the XP2i Series platform, the –DP has all the key features of the product line with additional capabilities that include: • 0.1% of reading accuracy wet/wet differential transducer • Excellent performance in long term high vacuum applications ④   OPERATING INSTRUCTIONS The XP2i-DP operates just like all the XP2i Series products. The uniqueness of the differential pressure capability comes from the integration of the differen tial sensor and process fitting system. The keypad and remote functions are the same as on all XP2i Series products. For further details about these common features, refer to the XP2i Operation Manual (P/N 4870). XP2i-DP Operation Manual Specifications ⚫ 2 Specifications Differential Pressure Accuracy 20 to 100% of Full Scale . . . . . . . . . .±(0.1% of Reading + Static Line Effect). 0 to 20% of Full Scale . . . . . . . . . . . .±(0.02% of Full Scale + Static Line Effect). Static Line Effect: 0.0003 psi/psi of lowest static pressure. Includes all effects of linearity, hysteresis, repeatability, temperature, and stability for one year. Temperature Operating . . . . . . . . . . . . . . . . . . . . . . .-10 to 50° C (14 to 122° F). Non-condensing. No change in accuracy over operating temperature range. Gauge must be zeroed to achieve rated specification. Storage . . . . . . . . . . . . . . . . . . . . . . . . . .-40 to 75° C (-40 to 167° F). Battery should be removed if stored for more than one month. Media Compatibility Liquids and gases compatible with 300 Series stainless steel and buna-n (o-ring). Pressure Conversions 1 psi = 27.6806 inches of water column (water at 4° C [39.2° F]) 27.7070 inches of water column (water at 15.6° C [60° F]) 27.7292 inches of water column (water at 20° C [68° F]) 2.03602 inches of mercury (mercury at 0° C [32° F]) 51.7149 millimeters of mercury (mercury at 0° C [32° F]) 703.087 millimeters of water column (water at 4° C [39.2° F]) 0.070307 kilograms per square centimeter 68.948 millibar 6.8948 kilopascals 0.068948 bar 0.006895 megapascals XP2i-DP Operation Manual Specifications ⚫ 3 Connections Pressure Connections . . . . . . . . . . . . 1/8" Female NPT (both + and – ports). Communication . . . . . . . . . . . . . . . . .DB9, RS-232 (environmentally sealed). Note: Do not use the RS-232 connector in a hazardous atmosphere. Display Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 digits. Display Rate . . . . . . . . . . . . . . . . . . . . .4 readings/second (standard). 8 readings/second (PSV mode). Numerical Display Height . . . . . . . . 16.9 mm (0.67") single line display. LCD readable in sunlight with bright backlight. Enclosure (U.S. Patent D612277) Weight . . . . . . . . . . . . . . . . . . . . . . . . . .915g (2.0 lbs), including batteries. Dimensions . . . . . . . . . . . . . . . . . . . . . . 165.1 mm (6.5") H x 112 mm (4.4") W x 33 mm (1.3") D. Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . IP67. Housing . . . . . . . . . . . . . . . . . . . . . . . . .Diecast, nickel plating over low copper, marine grade aluminum. Keypad and Labels . . . . . . . . . . . . . . .UV Resistant Polyester. Sensor Permanent fill dual diaphragm seal (filled with Dow Corning 200). Max Static Line Pressure . . . . . . . . . . 100 psi. ④   POWER Batteries . . . . . . . . . . . . . . . . . . . . . . . . . Three size AA (LR6) batteries. ! WARNING: Do not remove or change the batteries in hazardous locations. XP2i-DP Operation Manual Specifications ⚫ 4 Approved Batteries The XP2i-DP is Intrinsically Safe only if powered by one of the following battery types: Approved Battery Type Ta= Marking Rayovac Max Plus 815 -20 to 50° C Ex ia IIC T4 Ga Energizer E91* Energizer EN91* -20 to 50° C Ex ia IIC T3 Ga Duracell MN1500 Replace batteries with approved type in non-hazardous locations only * Energizer is manufactured by Energizer Holdings, Inc., and the Eveready Battery Company, Inc. Many other battery types and models have been tested but failed to meet the requirements for Intrinsic Safety—do not assume other models are equivalent. The XP2i-DP can be operated from an external power supply (P/N 2984). Do not mix battery types or manufacturers. ⇪ CSA: The XP2i is Intrinsically Safe only if powered by one of the following battery types: Approved Battery Type Ta= Marking Rayovac Max Plus 815 -20 to 45° C Class I, Division 1, A, B, C, D T4 Energizer E91 Energizer EN91 -20 to 50° C Class I, Division 1, A, B, C, D T3C Rayovac Max Plus 815 ! WARNING: Use of Duracell MN1500 batteries is not approved for CSA certification. ! WARNING: Do not use the AC Adapter kit in hazardous locations. Battery Life . . . . . . . . . . . . . . . . . . . . . .1500 hours typical (alkaline battery). Ultra Low Power . . . . . . . . . . . . . . . . .>1 year, typical with 20 minute recording interval in LT5 mode. Battery Indicator . . . . . . . . . . . . . . . . . 3-segment Battery Icon: ( ) : Full Battery ( ) : Used Battery ( ) : Low Battery Dead Battery Indication . . . . . . . . . .batt XP2i-DP Operation Manual Specifications ⚫ 5 ④   PRESSURE RANGES, DISPLAY SCALES, AND RESOLUTION psi bar kPa MPa Overpressure (+/– ports) psi inH20 inHg mmHg mmH20 kg/cm2 bar mbar kPa MPa 15PSI 1BAR 100KPA 0.1MPA 6.5x / 3.0 x 0.001 0.01 0.001 0.01 1 0.0001 0.0001 0.1 0.01 0.00001 100PSI 7BAR 700KPA 0.7MPA 2.0 x / 2.0 x 0.01 0.1 0.01 0.1 1 0.0001 0.0001 0.1 0.01 0.00001 • Unneeded pressure units may be disabled via the RS-232 connector using ConfigXP software. • An XP2i-DP will indicate pressure up to 10% above its stated pressure rating. Above 110%, the XP2i-DP display will flash, indicating that the applied pressure exceeds the calibrated pressure range. If the calibrated pressure range is exceeded, the pressure displayed may not be accurate. • Overpressure is the maximum pressure the gauge can withstand without damage. The gauge will not indicate pressure up to this value. • kPa and MPa models can display pressure in kPa, MPa, and bar (and/or mbar) only. psi and bar models can display all available units. XP2i-DP Operation Manual Applications ⚫ 6 Applications ④   DIFFERENTIAL PRESSURE The XP2i-DP may be used to determine accurate differential pressure measurements across a range of applications or installations such as filters, orifice plates, valves, etc. For example, in a piping system with an upstream static pressure of approximately 80 psig, the XP2i-DP may be used to determine the 10 psid pressure drop across the device under test (DUT). In this case, the product would be connected as shown below. XP2i Digital Test Gauge 100 PSID

Hi peak Lo FLOW 80 zero units clear XP2i-DP

PSI70 PSI Device Under Test (DUT) The pressure measurement accuracy of the gauge in this example is a combination of the standard accuracy statement and the static line pres sure effect. The 10 psid pressure, when compared to the 100 psi full scale product used, will require the 0 to 20% of Full Scale, ±(0.02% of Full Scale) accuracy statement. The static line pressure effect relates to the lowest test pressure applied in the test, or in this case 70 psi. The pressure measurement accuracy for this test condition is as follows: ±(0.02% x 100 psi) + (0.0003 psi x 70 psi) = ±0.04 psi. When using a 15 psi full scale gauge, this will require the 20 to 100% of Full Scale, ±(0.1% of Reading) accuracy statement. ±(0.1% x 10 psi) + (0.0003 psi x 70 psi) = ±0.031 psi. XP2i-DP Operation Manual Applications ⚫ 7 ④   CONTINUOUS VACUUM The unique design of the differential pressure sensor integrated into the XP2i-DP allows for long term vacuum use without fear of permanent damage to the sensing chip or package. When measuring high vacuum gauge pressures continuously it is recommended to connect the static line pressure to the right (–) port marked "Vacuum this side". To achieve gauge measurements, the left (+) port is left vented to atmospheric pressure. Vent Vacuum Note: When connected in this orientation, the XP2i-DP display will invert the sign on the gauge display. For example, a pressure of -12 psi on the negative port will display +12 psi. To invert the sign to read -12 psi, use ConfigXP Software (V 2.4 or later). Select Enable Vacuum Mode and update the gauge to properly display a negative pressure value. ! WARNING: Pressure applied to the + sensor port must be greater than or equal to the pressure applied to the – sensor port. The vacuum accuracy of the gauge will be calculated the same as a differential measurement. Therefore, the 12 psi measurement, when compared to a 100 psi full scale gauge used, will require the 0 to 20% of Full Scale, ±0.02 % of Full Scale accuracy statement. The vacuum accuracy for this test condition is as follows: ±(0.02% x 100 psi) = ±0.02 psi. When using a 15 psi full scale gauge, this will require the 20 to 100% of Full Scale, ±(0.1% of Reading) accuracy statement. ±(0.1% x 12 psi) = ±0.012 psi. XP2i-DP Operation Manual Safety & Certifications ⚫ 8

Safety & Certifications ④   HAZARDOUS LOCATIONS Every XP2i-DP pressure gauge includes the following Intrinsic Safety approvals: II 1G Ex ia IIC T4/T3 Ga Intrinsically Safe and Non-incendive for Hazardous Locations: Class I, Division 1,

ATEX FTZU 12 ATEX 0048X Ex ia IIC T4/T3 Ga IECEx FTZU 12.0009X Groups A, B, C and D, Temperature Code T4 or T3C.

! WARNINGS: The following warnings apply to the XP2i: • Do not use the RS-232 connector in hazardous locations. • Replace batteries in non-hazardous locations and with approved types only. • Do not mix battery types or manufacturers. • T4 or T3 Temperature Class is based on selection of approved battery. See Approved Batteries on page 4. • Special conditions for safe use: • The equipment shall not be installed in a location where external conditions are conducive to the buildup of electrostatic charge. • Because the enclosure of the XP2i and XP2i-DD is made of aluminium, if it is mounted in an area where the use of category 1 G apparatus is required, it must be installed such that, even in the event of rare incidents, ignition sources due to impact and friction sparks are excluded. ④   CERTIFICATIONS The XP2i-DP has been tested and certified to comply with a variety of international standards. This XP2i-DP complies with the Australian Radiocommunications (Electromagnetic Compatibility) Standard 2008. Crystal Engineering declares that the XP2i-DP is in accordance with the ATEX Directive, the Electromagnetic Compatibility Directive, and the Pressure Equipment Directive per our declaration(s). This XP2i-DP is approved for use as a portable test instrument for Marine use and complies with Det Norsjke Veritas’ Rules for Classification of Ships, High Speed & Light Craft, and Offshore Standards. XP2i-DP Operation Manual Support ⚫ 9 Support ④   SOFTWARE ConfigXP Configuration Software Use ConfigXP to disable unwanted pressure units, set default pressure units, change water density, adjust calibration, and more via the RS-232 interface. DataLoggerXP Software DataLoggerXP is an optional upgrade to transform the XP2i-DP into a pressure datalogging device. ④   REPLACEMENT PARTS The only user-replaceable parts are the batteries. ④   OPTIONS Panel Mounting (Option F4) A panel mount flange allows an XP2i-DP to fit in a 4½" gauge cutout. An XP2i-DP with the F4 option can also be adapted to 6 or 8½" gauge cutouts. Rear Port Fitting (Option RP) The rear port fitting may be ordered separately, but is included automatically with the panel mount flange option (F4). XP2i-DP Operation Manual Support ⚫ 10 ④   ACCESSORIES P/N 2984 AC Adapter Kit Permits operation of an XP2i-DP from an AC supply of 90 - 264 VAC and 47 - 63 Hz. Includes interchangeable international plugs (for USA, Europe, U.K., and Australia). Adapter will not charge batteries, but in the event of AC power loss, XP2is will automatically revert to battery operation. ! WARNING: Do not use the AC Adapter Kit in hazardous locations. P/N 3696 Protective Boot Skydrol™ resistant protective boot. ! WARNING: Do not use the Protective Boot in hazardous locations. P/N 2955 6" Gauge Adapter Kit Adapts the 4½" Panel Mount (F4 option) to fit into a 6" gauge cutout. P/N 2956 8½" Gauge Adapter Kit Adapts the 4½" Panel Mount (F4 option) to fit into an 8½" gauge cutout. P/N 3313 USB-RS232 Adapter USB B receptacle to RS232 DB9M. ! WARNING: Do not use the USB-RS232 Adapter in hazardous locations. P/N 2400 RS232 Cable DB-9 male to DB-9 female straight pass-through cable. ! WARNING: Do not use the RS232 Cable in hazardous locations. XP2i-DP Operation Manual Support ⚫ 11

④   CONTACT US USA Crystal Engineering • California* Tel +1 (800) 444 1850 Fax +1 (805) 595 5466 crystal@ametek.com Mansfield & Green • Florida Tel +1 (800) 527 9999 cal.info@ametek.com United Kingdom Tel +44 (0)1243 833 302 jofra@ametek.co.uk France Tel +33 (0)1 30 68 89 40 general.lloyd-instruments@ametek.fr Germany** Tel +49 (0)2159 9136 510 info.mct-de@ametek.de Denmark*** Tel +45 4816 8000 jofra@ametek.com India Tel +91 22 2836 4750 jofra@ametek.com Singapore Tel +65 6484 2388 jofra@ametek.com China Shanghai Tel +86 21 5868 5111 Beijing Tel +86 10 8526 2111 Guangzhou Tel +86 20 8363 4768 jofra.sales@ametek.com.cn

*ISO 17025 accredited calibration lab, (A2LA #2601.01). **DIN EN ISO / IEC 17025 accredited calibration lab. ***DANAK EN ISO/IEC 17025 accredited calibration lab. If calling, have ready the model number, serial number, date of purchase, and reason for return. You will receive instructions for returning the device to us. ④   FACTORY SERVICE Please complete the Return Material Authorization (RMA) form on our website. This will generate an authorization number and provide return instructions. ④   TRADEMARKS This manual contains the following third-party trademarks, both registered and unregistered. All marks are the property of their respective companies. Rayovac® and Maximum Plus™. . . . . . . . . . . . . . . . . Rayovac Corporation Duracell®. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Duracell Inc. Corporation Energizer® and Eveready. . . . . . . . . . . . . . . . . . . . . . . Eveready Battery Company, Inc. “Pressure is Our Business” is a registered trademark of Crystal Engineering Corp. ④   WARRANTY Crystal Engineering Corporation warrants the XP2i-DP Digital Test Gauge to be free from defects in material and workmanship under normal use and service for one (1) year from date of purchase to the original purchaser. It does not apply to batteries or when the product has been misused, altered or damaged by accident or abnormal conditions of operation. Crystal Engineering will, at our option, repair or replace the defective device free of charge and the device will be returned, transportation prepaid. However, if we determine the failure was caused by misuse, alteration, accident or abnormal condition of operation, you will be billed for the repair. CRYSTAL ENGINEERING CORPORATION MAKES NO WARRANTY OTHER THAN THE LIMITED WARRANTY STATED ABOVE. ALL WARRANTIES, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE, ARE LIMITED TO A PERIOD OF ONE (1) YEAR FROM THE DATE OF PURCHASE. CRYSTAL ENGINEERING SHALL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, WHETHER IN CONTRACT, TORT OR OTHERWISE. Note: (USA only) Some states do not allow limitations of implied warranties or the exclusion of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may have other rights which vary from state to state. XP2i-DP Operation Manual © 2016 Crystal Engineering Corporation 708 Fiero Lane, Suite 9, San Luis Obispo, California 93401-8701 4871.G


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply