ALTO PROFESSIONAL BLUETOOTH TOTAL MK2 (01) PDF Document

The box contents include the ALTO PROFESSIONAL BLUETOOTH TOTAL MK2, a Micro-USB Charging Cable, and the User Guide.

To charge the ALTO PROFESSIONAL BLUETOOTH TOTAL MK2, use the included micro-USB cable to connect the device to a USB power adapter (sold separately) connected to a power outlet or your computer (powered on).

Note: The device may not be fully charged upon purchase. While it is safe to use it right away, charging for 3-4 hours before initial use will ensure a full charge and the best performance.

The ALTO PROFESSIONAL BLUETOOTH TOTAL MK2 features the following controls and connections:

1. XLR Output

2. Stereo-Link Button

3. Stereo-Link LED

4. Pair Button

5. Pair LED

6. Power On/Off Switch

7. Power and Battery Status LEDs

8. Micro-USB Charging Port

When the unit is ON and not charging, the LEDs indicate the following battery levels:

20–100%: Green LED lit solid.

10–20%: Green and Amber LEDs are lit solid.

0–10%: Green and Red LEDs are lit solid.

Power Standby Mode: Green LED off. Red LED flashes once every 10 seconds.

When the unit is ON and charging, the LEDs indicate the following:

Power Standby Mode: Green LED off. Red LED flashes once every 10 seconds.

5–80% Charged: Green LED is off. Amber LED flashes slowly.

80–99% Charged: Green LED flashes slowly. Amber LED is off.

100% Charged: Green LED is lit solid. Amber LED is off.

When the unit is OFF and charging, the LEDs indicate the following:

5%–80% Charged: Green LED is off. Amber LED flashes slowly.

80%–99% Charged: Green LED flashes slowly. Amber LED is off.

100% Charged: Green LED lit solid. Amber LED is off.

To pair a single ALTO PROFESSIONAL BLUETOOTH TOTAL MK2:

1. Power on your Bluetooth device.

2. Power on the ALTO PROFESSIONAL BLUETOOTH TOTAL MK2.

3. Press and hold the Pair button for 3 seconds on the unit. A pairing tone will sound when it is in pairing mode.

4. Navigate to your Bluetooth device’s setup screen, find “Alto BT2” and connect.

5. When paired successfully, a confirmation tone will sound and the blue Pair LED will illuminate solid.

6. Adjust the volume on your Bluetooth device.

Note: Before pairing, turn off Wi-Fi on your device and stop any audio playback. To cancel the pairing process, press Pair again before your device is paired. When wirelessly connected to a single loudspeaker, the Left/Right audio signal will be summed to mono.

If your Bluetooth device prompts for a pairing code, enter “0000”.

To erase previous pairing settings, press and hold the Pair button for 10 seconds. A confirmation tone will sound, indicating that pairing settings have been erased. You can now pair to a new device.

1. Follow the steps 1-6 in the “Bluetooth Pairing a Single Bluetooth Total” section to pair your device to one unit.

2. Press and hold the Stereo-Link button for 3 seconds on the primary (left) ALTO PROFESSIONAL BLUETOOTH TOTAL MK2.

3. Press and hold the Stereo-Link button for 3 seconds on the secondary (right) ALTO PROFESSIONAL BLUETOOTH TOTAL MK2.

4. Both Stereo-Link LEDs will blink and a linking tone will sound while each unit “searches” for the other.

5. When they are successfully linked, each ALTO PROFESSIONAL BLUETOOTH TOTAL MK2 will produce a confirmation tone and the Stereo-Link LEDs on both units will be lit solid.

To erase linking settings on the linked unit, press and hold the Stereo-Link button for 10 seconds. A confirmation tone will sound, indicating that linking settings have been erased.

To erase linking settings on both units, press and hold the Stereo-Link button on the master unit for 10 seconds. A confirmation tone will sound, indicating that linking settings have been erased.