Free English JBL DECADE DS-10 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD JBL DECADE DS-10 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
How should I position the JBL DECADE DS-10 subwoofer for the best performance?
Place the subwoofer along the wall with the front speakers. Placing the subwoofer closer to a corner will increase the amount of bass output.
How do I connect the JBL DECADE DS-10 using Line-Level inputs regarding stereo receivers?
Connect the subwoofer using the Line-Level inputs. Note that some receivers/amplifiers have a single (mono) subwoofer output. In this case, it is recommended that you use a “Y”-connector (not included) to maximize the subwoofer’s performance.
How does the Speaker-Level connection work on the JBL DECADE DS-10?
When using the speaker-level connections, the built-in high-pass filter will also limit the low frequencies being sent to your satellite speakers. This means that your satellites won’t have to try to reproduce the information the subwoofer is playing.
What do the LED status lights indicate on the JBL DECADE DS-10?
| Mode | Procedure | LED Status |
|---|---|---|
| Off | Receiver/amplifier off | Red |
| On | Receiver/amplifier on and playing program material | Green |
| Standby | Simply turn off your receiver/amplifier. The subwoofer will turn off after approximately five minutes. The subwoofer will turn on when your receiver/amplifier begins playing again. | Red |
How do I set the Crossover Frequency on the JBL DECADE DS-10?
The crossover-frequency knob determines the highest frequency your subwoofer will reproduce. It allows a seamless transition from the subwoofer to the satellite speakers. Experiment with this adjustment to find the crossover frequency that sounds best with your speakers.
When the control is at the “50” position, very few high frequencies will be heard. This position is best suited to large main speakers.
For most users, the control should be set somewhere near the mid position.
For listeners using very small speakers, best results will be obtained with the control at the “150” position.
What steps should I take if I used the high-level (SPKR) inputs on the JBL DECADE DS-10 and there is no sound?
If you used the high-level (SPKR) inputs and there is no sound from any of the speakers, check the following:
• Receiver/amplifier is on and a source is playing.
• Powered subwoofer is plugged in.
• Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured.
• Review proper operation of your receiver/amplifier.
How can I troubleshoot low bass output on the JBL DECADE DS-10?
If there is low bass output, check the following:
• Make sure the connections to the left and right “Speaker Inputs” have the correct polarity (+ and –).
• Make sure that the subwoofer is plugged into an active electrical outlet.
• Powered subwoofer is plugged in.
• Adjust the crossover point.
What should I check if I used the line-level inputs on the JBL DECADE DS-10 and there is no sound from the subwoofer?
If you used the line-level inputs and there is no sound from the subwoofer, check the following:
• Receiver/amplifier is on and a source is playing.
• Powered subwoofer is plugged in.
• Check all wires and connections between receiver/amplifier and subwoofer. Make sure all wires are connected. Make sure none of the wires are frayed, cut or punctured.
• Review proper operation of your receiver/amplifier.
What are the technical specifications of the JBL DECADE DS-10?
Amplifier Power: 100 watts
Driver: 10″ polylaminate
Inputs: Line- and high-level
Outputs: High-level with high-pass filter at 180Hz (active only if high-level inputs are used)
Crossover Frequency: 50Hz – 150Hz (continuously variable)
Frequency Response: 35Hz – 150Hz (determined by crossover setting)
Dimensions (H x W x D): 14-1/4 x 14-1/4 x 16 inches (362 x 362 x 406mm)
Weight: 27 lbs/12.3 kg
What are the important ventilation requirements for the JBL DECADE DS-10?
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered.
The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface.
This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
CLICK HERE TO DOWNLOAD JBL DECADE DS-10 (01) PDF DOCUMENT