Free English ALECTO GA-10 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD ALECTO GA-10 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What is the function of the ALECTO GA-10?
The ALECTO GA-10 is a gas detector designed to discover gas leaks in the first phase.
What sound level does the ALECTO GA-10 produce during an alarm?
When gas is detected, the ALECTO GA-10 will emit a loud alarm tone of at least 85dB (A).
How often should I test the ALECTO GA-10?
It is advisable to test the ALECTO GA-10 weekly by using the test button.
Where should I install the ALECTO GA-10?
It is advisable to place multiple ALECTO GA-10 detectors to increase security. Place at least one detector in the kitchen and garage, where equipment present may cause fire.
What is the correct way to mount the ALECTO GA-10 to the ceiling?
When mounting the ALECTO GA-10 to the ceiling, place it at a minimum distance of 50 cm from any wall and 61 cm from any corner.
Where should I avoid installing the ALECTO GA-10?
You should avoid installing the ALECTO GA-10 in the following locations:
1. Within 3 meters of any cooking apparatus.
2. In the bathroom, as hot showers may cause false alarms.
3. Near a fan or near the exhaust of an air conditioner or heater.
4. In the nook of an A-shaped ceiling.
5. In rooms where the temperature can reach below 0°C or beyond 45°C.
Can I paint the ALECTO GA-10?
No, you should not paint the ALECTO GA-10 or cover it in any way.
How do I perform the initial installation of the ALECTO GA-10?
Follow these steps to install the ALECTO GA-10:
1. Install the ceiling plate on a location using plugs and screws.
2. Remove the plastic foil from the battery, plug it in the cable inside the battery compartment, and place it firmly inside the compartment.
3. Place the ALECTO GA-10 on the ceiling plate and rotate it to secure.
4. Plug in the adapter using the port on the side of the detector and plug it into a power outlet.
5. Test the detector first by holding the test key for 2 seconds. The green LED will turn on to show the detector is operational.
What does a blinking green LED on the ALECTO GA-10 indicate?
If the green LED on the ALECTO GA-10 blinks every 30 seconds, the device is not connected to main power but is operating on battery power.
What does a blinking red LED on the ALECTO GA-10 indicate?
The blinking red LED on the ALECTO GA-10 indicates that the device is still warming up or that the hush mode is active.
How does the hush function work on the ALECTO GA-10?
The hush function on the ALECTO GA-10 allows you to deactivate the alarm for 5 minutes. You can activate this by pressing the button once shortly. The red LED will blink to indicate the alarm is silenced. After 5 minutes, the blinking will stop and the alarm will be reactivated.
What should I do if the ALECTO GA-10 gives a false alarm while cooking or showering?
If the ALECTO GA-10 gives a regular false alarm, first try cleaning the gas detector with a vacuum cleaner. If the issue persists, move the ALECTO GA-10 to another location.
Why is my ALECTO GA-10 beeping every minute?
If the ALECTO GA-10 is beeping every minute, replace the 9V battery and check that the adapter is properly connected.
What should I do if there is no sound during the test procedure on the ALECTO GA-10?
If there is no sound during the ALECTO GA-10 test procedure:
1. Remove the detector from the ceiling plate and check if the battery and adapter are properly connected.
2. Clean the ALECTO GA-10 using a vacuum cleaner.
Note: Ensure you hold the test button for several seconds during the test.
How do I perform regular maintenance on the ALECTO GA-10?
The ALECTO GA-10 can be cleaned with a vacuum cleaner to keep it free of dust. It is important to protect the detector against dust during any renovation work.
What are the troubleshooting steps for the ALECTO GA-10?
| Problem | Solution |
| No sound during the test procedure | 1. Remove the detector from the ceiling plate and check if the battery and adapter is properly connected. 2. Clean the ALECTO GA-10. |
| The ALECTO GA-10 beeps every minute | Replace the 9V battery and check the adapter. |
| The ALECTO GA-10 regularly gives a false alarm during cooking or showering | 1. Clean the ALECTO GA-10. 2. Move the ALECTO GA-10 to another location. |
| Green LED blinks every 30 sec. | Device not connected on main power, but works on battery. |
| Red LED blinks | The device is still warming up or hush mode is active. |
How do I know if the ALECTO GA-10 is operational?
The ALECTO GA-10 is operational if the 9 volt battery is placed and the unit is connected by adapter. When operational, the red LED will blink initially, then turn green after calibration.
What should I do if the ALECTO GA-10 alarm goes off?
If there is any doubt over the cause of an alarm from the ALECTO GA-10, assume the alarm is caused by a gas leak and evacuate the premises as soon as possible.
Does the ALECTO GA-10 stop the alarm automatically if gas dissipates?
Yes, once the gas dissipates, the alarm from the ALECTO GA-10 will stop automatically.
What are the technical specifications for the ALECTO GA-10 regarding temperature?
The usage temperature for the ALECTO GA-10 is 4°C to 60°C.
What is the power supply requirement for the ALECTO GA-10?
The ALECTO GA-10 requires 12VDC, 200mA power with 9V DC backup.
How does the ALECTO GA-10 detect gas?
Gas typically moves upwards to the ceiling first and then travels horizontally, which is why the ALECTO GA-10 is designed to be mounted on the ceiling for optimal detection.
Can I mount the ALECTO GA-10 on a wall?
Wall mounting the ALECTO GA-10 may technically be possible, but it will result in a slower alarm response compared to ceiling mounting.
Is the ALECTO GA-10 safe to use around children?
The ALECTO GA-10 should be kept away from small children.
What is the alarm point of the ALECTO GA-10?
The alarm point of the ALECTO GA-10 is less than 15% LEL.
What should I do with old batteries from the ALECTO GA-10?
Do not throw away used batteries from the ALECTO GA-10 with normal household waste; recycle them using your local chemical depot.
How do I properly test the ALECTO GA-10?
To test the ALECTO GA-10, press the test key and hold it for at least 2 seconds. Operation is correct if the red LED blinks and a tone is audible.
Does the ALECTO GA-10 require calibration after the battery is placed?
Yes, after the ALECTO GA-10 is powered on, it will undergo calibration, after which the LED will turn green to indicate it is ready.
Are there any specific cleaning instructions for the ALECTO GA-10?
The ALECTO GA-10 should be cleaned using a vacuum cleaner to remove any accumulated dust that could affect its functionality.
What happens if the ALECTO GA-10 is covered by dust?
If the ALECTO GA-10 is covered by dust, it will lose its functionality.
How is the ALECTO GA-10 handled at the end of its life?
The ALECTO GA-10 must not be thrown out as normal waste but must be recycled as electrical waste.
Can I use the ALECTO GA-10 to detect fires?
Can I use the ALECTO GA-10 to detect fires?
The ALECTO GA-10 is a gas detector. While it should be placed in areas like the kitchen and garage where equipment present might cause a fire, its primary function is to detect gas leaks.
What is the minimum distance required between the ALECTO GA-10 and cooking apparatus?
The ALECTO GA-10 should be kept at least 3 meters away from any cooking apparatus.
Why should I avoid corners when mounting the ALECTO GA-10?
Due to natural airflow, corners of a room will slow down or prevent the detection of gas by the ALECTO GA-10.
How do I verify the ALECTO GA-10 is operational after it is set up?
After installation, the ALECTO GA-10 needs to warm up. Once operational, the green LED will turn on.
Can I test the ALECTO GA-10 immediately after power-up?
It is recommended to wait 5 minutes for the ALECTO GA-10 to warm up before performing the first test.
Does the ALECTO GA-10 use a backup battery?
Yes, the ALECTO GA-10 uses a 9V battery as a backup power source.
How do I ensure the battery is correctly installed in the ALECTO GA-10?
Remove the plastic foil from the battery, plug it into the cable inside the ALECTO GA-10 battery compartment, and place it firmly inside the compartment.
Can the ALECTO GA-10 be installed on the ceiling with ease?
Yes, once the battery is installed in the ALECTO GA-10, you can place the detector on the ceiling plate and rotate it easily to secure it.
Does the ALECTO GA-10 alarm sound constantly during a gas leak?
If gas is detected by the ALECTO GA-10, a loud beep will sound and the red LED will blink continuously until the gas dissipates.
How does the ALECTO GA-10 react to changes in temperature during an alarm?
If the gas dissipates, the ALECTO GA-10 alarm will stop automatically.
Can I use the ALECTO GA-10 if the red LED is blinking?
If the red LED on the ALECTO GA-10 is blinking, it indicates the device is still warming up (max 5 minutes) or is in hush mode, and it may not be ready to detect gas.
What is the sound level of the ALECTO GA-10 at a distance of 1 meter?
The ALECTO GA-10 produces a sound level of 85dB at a 1-meter distance during an alarm.
What should I consider when placing the ALECTO GA-10 in a garage?
You should place the ALECTO GA-10 in the garage as it is an area where equipment present may cause a fire.
How should I store the ALECTO GA-10 manual?
Save this manual for the ALECTO GA-10 in a secure location, like the fuse box cabinet.
Is the ALECTO GA-10 suitable for mounting near an air conditioning unit?
No, you should not place the ALECTO GA-10 near a fan or near the exhaust of an air conditioner or heater.
What is the purpose of the test button on the ALECTO GA-10?
The test button on the ALECTO GA-10 allows you to verify that the alarm and detector are still operational.
Can I use the ALECTO GA-10 in a room that is unheated?
Do not place the ALECTO GA-10 in rooms where the temperature can reach below 0°C.
Are there limitations for ALECTO GA-10 installation on A-shaped ceilings?
Do not place the ALECTO GA-10 in the nook of an A-shaped ceiling.
How do I verify the ALECTO GA-10 is working correctly during a test?
Operation of the ALECTO GA-10 is correct if the red LED blinks and a tone is audible while the test button is held down.
Does the ALECTO GA-10 require a wall-mounted ceiling plate?
Yes, the ALECTO GA-10 requires the installation of a ceiling plate using plugs and screws before the detector unit can be rotated into place.
What is the main advantage of placing multiple ALECTO GA-10 detectors?
Placing multiple ALECTO GA-10 detectors increases the security coverage in your home.
CLICK HERE TO DOWNLOAD ALECTO GA-10 (01) PDF DOCUMENT