AIRSTREAM GLOBETROTTER 2025 (01) PDF Document

Making sure wheel mounting nuts (lug nuts) on trailer wheels are tight and properly torqued is an important responsibility. Use a torque wrench to tighten lug nuts. Tightening by hand or with an impact wrench is not recommended.

Lug nut torque (Max), aluminum wheels: 110 ft lbs.

Lug nut torque (Max), steel wheel (spare): 100 ft lbs.

Immediately after the purchase of your new recreational vehicle, and sometimes, after it has been closed up for an extended period of time, you may notice a strong odor and/or experience a chemical sensitivity. This is not a defect. To reduce or lessen exposure to chemicals from off-gassing, it is of utmost importance that you ventilate your recreational vehicle. Ventilation should occur frequently after purchase and at times when the temperatures and humidity are elevated.

Open windows, exhaust vents, and doors. Operate ceiling and/or other fans, roof air conditioners, and furnaces. Use a fan to force stale air out and bring fresh air in. Decreasing the flow of air by sealing the recreational vehicle increases the formaldehyde level in the vehicle’s indoor air.

The LPG/CO detector is located in the galley area. It is wired directly to your trailer battery. If the Silence/Test button is pressed while in normal operation, the alarm will perform a self test of the CO sensor, propane sensor and battery voltage. It is recommended to perform a self test weekly, after power up from storage, and before each trip.

If the self test passes, the alarm will perform 2 cycles of the CO horn pattern (4 rapid chirps followed by a 4 second pause), followed by 2 cycles of the propane horn pattern (constantly beeping).

If the low voltage warning sounds, the detector will need to be reset by disconnecting the battery, before normal operation will occur.

1. Extinguish any open flames, pilot lights, and all smoking materials.

2. Do not touch electrical switches.

3. Shut off the gas supply at the tank valve(s) or gas supply connection.

4. Open doors and other ventilating openings.

5. Leave the area until odor clears.

6. Have the gas system checked and leakage source corrected before using again.

1. Turn off water pump switch.

2. Close windows and vents.

3. Lock all interior cabinet doors.

4. Latch refrigerator door. (Seal containers first.)

5. Hold down or securely stack all loose, hard, and sharp objects.

6. Fasten sliding and foldette doors.

7. Drain toilet bowl.

8. Turn off interior lights.

9. Lower wall mounted tables to be even with dinette seats. Place Pedestal tables in upright position.

10. Pull up or retract step.

11. Lower blinds.

12. Secure and lock main door.

1. Disconnect and stow the electrical hookup cord, the sewer (flush out), and water hookup hoses.

2. Turn off gas at LP tanks.

3. Retract stabilizing jacks.

4. Check hitch for proper attachment.

5. Check safety chains and breakaway switch cable.

6. Fully retract hitch jack. Remove and stow jack stand or wood block.

7. Check clearance and stoplights.

8. Check lug nuts.

9. Check tires for correct pressure.

10. Adjust tow vehicle mirrors.

11. Pull forward about 50 ft, test brakes, and check site for forgotten objects and cleanliness.

1. Block or chock the wheels to keep the trailer from rolling.

2. Level from side to side first. This can be done easily by backing the trailer up onto one or more 2 x 6 boards.

3. Level from front to rear by disconnecting the hitch from the tow vehicle, putting the jack pad under the hitch jack, and adjusting the jack up or down until the trailer is level.

4. Use stabilizing jacks at all four corners to eliminate the natural spring action of the axles.

Note: Stabilizing jacks should only be used to stabilize the trailer. Do not use jacks to lift the trailer.

The vinyl upholstery has a PermaBlok3® vinyl protective coating. Most stains can be removed with a damp cloth and cleaned with a 1:1 mix of Ivory® soap and water. A 1:1 mix of ammonia and water, or a 1:4 mix of bleach and water can be used for more stubborn stains. Only if needed a 1:1 mix of isopropyl alcohol and water can be used.

Use only a soft cotton cloth and rub the stain in a circular motion. Rinse thoroughly with clean water and pat dry. Never remove cushion covers for separate dry cleaning or washing.

1. Locate the tabletop slide latch on the underside and pull it outward to remove tension. This allows the top to be centered between the dinette seats as it is lowered.

2. Pull and hold the lever for the pedestal. Push on the top to get it moving downward. Release the lever and continue pushing down, centering the table as you lower it. You will hear a click when the table is fully lowered and latched into position.

3. Reengage the tabletop slide latch and lay the dinette seat backrest cushions over the tabletop to complete the conversion.

To resume using the dinette, remove the cushions and pull the pedestal lever to raise the table (pulling up on the table as necessary).

1. Pull the round center covers off each floor base.

2. Find the T-bolts on the bottom of each leg and turn them counterclockwise until extended.

3. Align and insert the T-bolts into the rectangular openings in each floor base. Twist the legs clockwise and tighten until snug.

4. Align the tabletop sockets with the legs and push down on the top until it is seated on the legs.

To convert the 30RB dinette to bed lift the tabletop up and off the legs. Remove the dinette legs and store them. Replace them with the shorter bed legs found in the wardrobe using steps 2-4 above. Lay the provided cushions across the tabletop to complete the conversion.

The switch for the water pump is located on the monitor panel. When turned on, the water pump’s controller maintains a consistent regulated water pressure and steady water flow based on demand. The water pump is typically left off when hooked up to a city water supply. However, if city water pressure is lower than desired the water pump can be turned on to facilitate increased water pressure, provided there is a supply of water in the fresh water tank.

Note: Road vibration may force a faucet open in transit. Ensure the pump is OFF prior to travel.

The battery disconnect switch is used to separate the batteries from the 12-volt distribution panel.

When the trailer is plugged into an external AC power source, the 12-volt distribution panel will receive power from the converter and the batteries will be charged regardless of the switch position. The battery disconnect switch must be on to use the inverter.

If the trailer is NOT plugged into an external AC power source and the switch is turned to OFF, the batteries are disconnected. The OFF position is intended for storage of the trailer or when power conservation is desired.

The fan is equipped with a built-in thermostat and rain sensor. Select the thermostat setting and the fan will automatically turn on and off as your trailer heats up and cools down. When the rain sensor becomes wet the dome will close automatically and shut the fan off. Some models will automatically open and run once the sensor is dry.

Note: If the lid is opened manually, the rain sensor will not close the lid automatically. The sensor must be dry for the fan to operate.

To clean the screen, turn the fan motor and battery disconnect switch OFF. The screen may be friction held or have retainer clips. Remove the screen and clean with a mild soap and water solution.

System Button:

– OFF: System is OFF.

– HEAT: Heating mode will operate when zone temperature is one degree below setpoint.

– COOL: Rooftop unit in selected zone will operate according to mode setting.

Mode Button (System Set to Cool):

– COOL AUTO: Default setting. Cycles cooling and fan speed varies.

– COOL HIGH/LOW: Cycles cooling based on demand, fan runs continuously.

– FAN HIGH/LOW: Fan only/no cooling.

Mode Button (System Set to Heat):

– GAS: System runs only the furnace.

– ELEC: System runs heat pump. Automatically switches to furnace if room temp is 5 degrees or more below setpoint.

Temperature Up/Down: Press UP or DOWN to select desired temperature setpoint.

Zone Button: Press to toggle from one zone to the next.

To operate the step, lift up on the front of the step and pull straight out until step locks into place. Some units will be equipped with a double step. After extending the step, the second portion folds out. To store the step, fold it back into position, lift the front slightly and push the step back into its storage area.

Never travel with step lowered or extended.

Close and lock the door from the exterior using the keys in the following order:

1. DOOR HANDLE: Insert the ROUND KEY and rotate it counterclockwise until it stops and an audible CLICK is heard; rotate the key back approximately 1/4-turn to the vertical position to remove it.

2. DEADBOLT: Insert the SQUARE KEY and rotate it counterclockwise until it stops and an audible CLICK is heard; rotate the key back approximately 1/4-turn to the vertical position to remove it.

Pull on the handle to verify the door is secured.

The awning’s primary function is sun protection. Roll up your awning in case of rain, wind, or snow.

Units with power awnings installed have a power awning lock switch located on the awning control panel. When OFF this switch will disconnect the power to the awning. The awning lock switch should be turned OFF while traveling.

If the power to the awning has been turned off or interrupted, the entry door must be closed before retracting the awning to allow the awning controller to reestablish its “home” position by completing a “closed/reset cycle”.

The gravity water fill is located on the side of the trailer, behind a locked compartment. Fill the water tank by inserting a high-pressure RV/Marine FDA approved drinking water hose of at least 1/2-in. diameter made from material that is tasteless, odorless, and non-toxic. The amount of water in the tank may be checked on the Monitor Panel.

The city water hook-up is located on the side of the trailer. Use a tasteless, odorless, non-toxic, high-pressure hose of at least 1/2-in. diameter designed for RV use. The city water inlet is a standard garden hose thread.

After hooking up the hose and turning on the city water valve, slowly open a faucet. There will be sputtering until air is expelled. Your plumbing system has a built-in pressure regulator to protect your lines.

1. Make sure the coupler is properly lined up with the ball.

2. Lower the coupler. The coupler will automatically open and latch into place when lowered onto the hitch ball.

3. Always make sure coupler is properly attached and latched before towing.

To disengage coupler, pull up on latch and raise coupler off of hitch ball.

To change a tire with a jack, see the label affixed to the underbelly located to the rear of the wheels reading JACK with an arrow pointing to the mainframe rail where the jack head must be placed. Airstream does not supply a jack with the trailer.

Leveling blocks can be used instead of a jack. Position the leveling block under the trailer’s good tire. This will raise the flat tire clear of the ground.

Never attempt to change any tire on the trailer without securely chocking the trailer’s remaining wheels.

1. Level the trailer from side to side and front to rear. Open all faucets.

2. Turn the water pump switch to the ON position to expel water from the storage tank.

3. Open all drain valves including exterior water service valve, if applicable.

4. While water is draining, open and flush the toilet-flushing valve. Operate the shower head while holding it down inside the tub and drain all water from the flexible hose.

5. Turn the pump switch OFF after all water has been removed from the storage tank.

6. Disconnect outlet hose from water pump. Turn the pump on until all the water is expelled.

7. Reconnect the water pump outlet.

8. Lower the front of the trailer as far as the jack will allow and let the trailer sit until water ceases to drain, then crank the jack up as high as it will go until water ceases to drain.

9. Apply, at max, 30PSI air pressure to the city water inlet until only air is coming out of the faucets.

10. Pour a cup of non-toxic RV antifreeze into the lavatory, sink and tub drains.

11. Open waste-holding tank dump valves and drain and flush the tanks thoroughly.

12. Remove the batteries and store in a cool, dry place.

A 1,000-watt generator may be used to charge just the batteries. However, if you want to run appliances such as microwave or AC units, it is recommended to have at least 4,000 watts or more (This is for a 30 amp system). Many Airstreamers accomplish this using two portable generators running in parallel.

These plugs are designed for no more than 2000 watts of power and are intended for charging things such as laptops and phones, and TV usage. Plugging in items such as vacuums, hairdryers, etc., may harm the system.

The jack may be raised and lowered using the hand crank provided. Check for 12V power and proper grounding at the jack.

First, empty your black water tank, then close your black water tank valve. Hook up your hose to the external hookup, run a couple minutes, and then open the valve. Do this a couple of times until clear.

Your main door is designed differently than a flat surface door. The door is over-bent in order to apply more pressure at the top and bottom of door for better sealing. Also, on uneven surfaces, the trailer can be in a slight twist that could affect closing. Make sure trailer is as level as possible.

Your windows have rubber seals around the edges which in extreme heat and dusty conditions can become sticky. You can help prevent this by regularly cleaning window seals with soapy water and applying a silicone product or Aerospace Protectant 303 to the seals. Clean edge of glass also.