AIGOSTAR 330100TRW (01) PDF Document

Always observe the following basic safety precautions when using your AIGOSTAR 330100TRW Air Cooler:

1. Ensure there is sufficient space between the air inlet and any wall or furnishings. If the air flow is blocked, the wind cooling functionality will not be effective.

2. Before first use, please check if the voltage of your electricity supply is compatible with the voltage detailed on the nameplate of the air cooler.

3. Before use, please ensure the power cord and plug are not damaged or broken. Do not allow the power plug or cord to become twisted.

4. To avoid a hazard, if the power cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons.

5. Do not cover the air outlet and keep the air fan away from the electricity socket. Ensure you use an outlet that has a current above 10A. Do not plug any other appliance into the same socket.

6. When the air cooler is in use, do not insert your hand or foreign object into the outlet (ensure children are supervised at all times).

7. The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capability, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the safe use of the appliance by the person responsible for their safety.

8. Children should be supervised to ensure they do not play with the appliance.

9. Please turn off the power before unplugging the appliance. When removing the plug, always hold the power plug. Never pull the cord as this poses a risk of short-circuit, fire, and/or electric shock.

10. Do not operate the appliance or remove the plug if you have wet hands as this can cause a risk of electric shock.

11. Please remove the plug from the socket when the appliance is not in use.

12. Please do not put the working air cooler on an uneven or slippery surface.

13. Please do not use the air cooler outdoors or close to water; for example, in a poolroom or bathroom.

14. When the air cooler is being used in combination with the cooling (humidifying) function, the level of water in the water tank must be less than the “Max” level and above the “Min” level at all times.

15. After the water tank has been filled with the correct amount of water, please do not lean upon, bump, or rock the air cooler.

16. Please do not place any objects on the air cooler.

The main parts of the AIGOSTAR 330100TRW Air Cooler are:

• Control panel

• Air outlet

• Swivel caster

• Water tank

• Air filter

• Wet curtain paper

• Water pump

• Ice box (*2)

• Back/Air inlet

• Upper water tank

To install the castor wheels, remove the AIGOSTAR 330100TRW Air Cooler from its packaging and turn it upside down. Insert the wheels into the bottom holes and fix them in place. The appliance is now ready for use.

1. Insert the plug into a standard AC socket. Ensure the plug fits securely in the socket. The buzzer will sound, and the POWER indicator will illuminate.

2. Press the “ON/OFF” button to start or stop the fan. The default fan speed is “Low,” and the default fan mode is “Normal.”

Press the “SPEED” button to set the desired fan speed. The options are “High”, “Medium,” or “Low”. This will illuminate the corresponding speed indicator light while the fan is operating.

Press the “MODE” button to choose the desired mode. There are three modes:

1. “Normal” (the mode indicator is off).

2. “Natural” (the mode indicator is flashing).

3. “Sleep” (the mode indicator is on).

In Natural mode, the fan speed cycles through different levels to simulate a natural breeze. The pattern depends on the selected speed setting:

Natural mode + Low speed: The fan cycles through a pattern of Low, Medium, and High speeds, shifting every three seconds.

Natural mode + Med. Speed: The fan cycles through a pattern of Low, Medium, and High speeds, shifting every three seconds.

Natural mode + High speed: The fan cycles through a pattern of Low, Medium, and High speeds, shifting every three seconds.

In Sleep mode, the fan speed gradually decreases over time to provide a comfortable sleeping environment.

Sleep mode + Low speed: The appliance keeps running at a low speed.

Sleep mode + Med speed: The appliance runs at a medium speed for 30 minutes and then continues running at a low speed.

Sleep mode + High speed: The appliance runs at a high speed for 30 minutes, then medium for 30 minutes, and then continues running at a low speed.

Set the desired shutdown time by pressing the “TIMER” button. The options are 2, 4, 6, 8, 10, and 12 hours. The corresponding time indicator light will illuminate.

Press the “SWING” button to move the internal blades from side to side. This will illuminate the swing indicator light. Press the “SWING” button again to stop the process, at which point the swing indicator light will go out.

Press the “COOL” button. The air will be cooled if you have added water or ice. The cool indicator light will illuminate when the “COOL” button is pressed. Press the “COOL” button again to stop the cool function. The cool indicator light will go out.

Caution: Do not start the cool function if there is no water in the water tank as this will damage the water pump. DO NOT add water when the power is on. The appliance will auto power off when water shortage occurs.

Turn the small knob, pull out the water tank, and ensure the water tank escape valve is properly affixed. Fill the water tank with clean water. Make sure you fill above the minimum level and do not exceed the maximum level (after the addition of any ice or ice blocks).

You can also add water via the upper water tank.

If you find the air is not cool enough, add extra ice blocks to the water tank.

If you wish to use an icebox (two iceboxes are included) instead of ice blocks, fill the icebox with water, being sure not to exceed the maximum level indicated. Place it in your freezer and leave it for 1 to 2 hours. Then put the frozen icebox in the water tank or upper water tank.

The functions on the control panel can be controlled using the remote control by pressing the corresponding function buttons. To install the battery, open the battery cover on the back of the remote and insert the battery according to the polarity indicators.

Unplug the power, unscrew the air filter, and take the air filter apart. Clean it using a neutral cleaner and soft brush. Rinse using clean water. Reinstall the air filter in the air cooler after cleaning.

Take the wet curtain paper out from the air filter and clean it using clean water and a soft brush. Reinstall the wet curtain paper after cleaning. To avoid any leakage, the wet curtain paper must be installed properly.

Unplug the power supply, turn the two fixed knobs to separate the escape valve and take the water tank out. Wipe off any scale that can be observed in the water tank using a clean towel and cleaner. Rinse the water tank with clean water and then reinstall it in the air cooler.

Wipe off the housing using a neutral cleaner and soft cloth.