FREE ENGLISH AICOK AMR516 (01) PDF USER GUIDE
FREE ENGLISH AICOK AMR516 (01) PDF USER MANUAL
FREE ENGLISH AICOK AMR516 (01) PDF OWNER GUIDE
FREE ENGLISH AICOK AMR516 (01) PDF OWNER MANUAL
FREE ENGLISH AICOK AMR516 (01) PDF REFERENCE GUIDE
FREE ENGLISH AICOK AMR516 (01) PDF INSTRUCTION GUIDE
FREE ENGLISH AICOK AMR516 (01) PDF REFERENCE MANUAL
FREE ENGLISH AICOK AMR516 (01) PDF INSTRUCTION MANUAL
FREE ENGLISH AICOK AMR516 (01) PDF OPERATING INSTRUCTIONS
CLICK HERE TO DOWNLOAD AICOK AMR516 (01) PDF MANUAL
If this is not the document you want for this product, click here to see if we have any other documents for this product.
AICOK AMR516 (01) PDF SUMMARY:
What should the input voltage of the product be before use?
The product should have an input voltage of 120V ~60Hz before use.
What should you do before dismantling, assembling, or adjusting any part of the product?
You should disconnect the power supply before dismantling, assembling, or adjusting any part.
What should you do if the power cable is damaged?
If the power cable is damaged, you should contact customer service or have it replaced by a designated service center. Do not dismantle and repair the product by yourself.
What should you check before using the product?
Before use, check whether any parts such as the power cable or the plug is damaged. If it is, stop using the product and contact customer service. Do not dismantle and repair the product yourself.
What should you do if product maintenance is necessary?
If product maintenance is necessary, contact customer service or have the maintenance done by a designated service center. Do not dismantle the product yourself.
What should you make sure of before connecting the power supply?
Before connecting the power supply, make sure detachable parts such as the juice strainer and the top cover are properly installed.
What should you never do when the product is running?
When the product is running, never put hands or sharp articles into its feed opening, or replace the pushing rod with any object, or have eyes close to the feed opening.
What should you keep away from the operator’s body when the product is running?
Keep the juice strainer or motor wheels from the operator’s body and other hard foreign matters when the product is running.
When should you not dismantle the detachable parts of the product?
After juicing, do not dismantle the detachable parts of the product until the motor and the juice strainer have both stopped and the power supply has been disconnected.
What is the maximum time you should juice continuously?
Juice continuously for 1 minute at most each time.
How long should you stop after the end of any function?
After the end of any function, stop for 2 minutes to end a cycle.
How long should you stop after 3 successive cycles?
Stop for 15 to 20 minutes after 3 successive cycles.
What should you do if the product stops running in use?
If the product stops running in use, it is possibly caused by temperature protection of the motor. Disconnect the power supply for cooling and use the product 15 to 20 minutes later.
What should you not use to disinfect any accessories?
Do not disinfect any accessories in hot water above 80 °C or microwave ovens.
What should you not do with the main unit of the product?
Do not place the main unit of the product into water or other liquids, or flush it with water or other liquids. It can be wiped with a soft cloth.
What should you not use to clean the product?
Do not clean the product with steel wool, abrasive cleansers, or corrosive liquids (such as gasoline or acetone).
Where should you put the product?
Put the product in a place out of reach of children.
Who is prohibited from using or playing with the product?
Use or play of the product by persons with disabled limbs or sensory or mental disorders or by persons without relevant experience or knowledge (including children) is forbidden.
What should you do before processing fruits or vegetables with cores, hard seeds, or shells or thick skins?
Do not process any fruits or vegetables with cores, hard seeds or shells or thick skins until their cores, hard seeds or shells or thick skins have been removed.
Who is the product suitable for?
The product is suitable for individuals or families only.
What are the functions of the pushing rod?
The pushing rod is for gently pushing food materials in the food material feeding to ensure full contact between the food materials and the juice strainer and prove the juicing efficiency.
What are the functions of the top cover?
The top cover connects with the main unit and is a key part for juicing, realizing safety protection.
What are the functions of the juice strainer?
The juice strainer is for cutting food materials by the cutter holder at its bottom and filtering juice and separating fruit residues by the lateral strainer.
What is the function of the motor wheel?
The motor wheel connects the juice strainer and makes the juice strainer align automatically for convenient handling.
What is the function of the middle ring?
The middle ring discharges the juice separated by the juice strainer by means of pressing.
What is the function of the juice cup cover?
The juice cup cover keeps foreign bodies out when accepting juice.
What is the function of the baffle?
The baffle separates the fruit juice from foam.
What is the function of the juice cup?
The juice cup is a container for accepting juice, and it’s easy for cleaning.
What is the function of the knob switch?
The knob switch controls the operating status (including inching, low speed, and high speed) of the product.
What is the function of the main unit?
The main unit contains parts such as the motor and serves as the power source of the product.
What is the function of the pull rod?
The pull rod is a key component for starting the safety switch, locking the body and header to allow the machine under normal working condition.
What is the function of the fruit reside cup?
The fruit reside cup collects the fruit residues separated by the juice strainer by means of pressing.
What should you do before using the product for the first time?
Clean its parts in contact with food materials thoroughly before using the product for the first time.
What are the different gears for?
0: For closing and stopping Inching: Inching 1: A low-speed gear for processing soft fruits and vegetables such as watermelon, tomato, cucumber, and strawberry 2: A high-speed gear for processing all fruits and vegetables.
What is the first step for installing the product for juicing?
Install the middle ring on the body.
What is the second step for installing the product for juicing?
Put the juice strainer into the middle ring and properly install it on the motor wheel. Before use, check whether the juice strainer is damaged. If it is, do not use the product but contact a near service center at once.
What is the third step for installing the product for juicing?
Install the pomace cup.
What is the fourth step for installing the product for juicing?
Put the header right above on the body and properly install it as per the direction indicated on the header.
What is the fifth step for installing the product for juicing?
Put the pulling rod inside the two grooves of header until completely in place, or the product will not work normally.
What is the sixth step for installing the product for juicing?
Allow the fruit juice cup baffle slide in the juice cup along the neck, put on the cup cover.
What is the seventh step for installing the product for juicing?
Put juice cup under the outlet.
What is the eighth step for installing the product for juicing?
Align the groove of pushing rod with the flange inside the feeding port and put the pushing rod inside the feeding port.
What is the ninth step for installing the product for juicing?
Connect the power supply and prepare for run. Make sure the switch is off before connecting the power supply.
What should you do with the fruits and vegetables before juicing?
Clean fruits and vegetables and cut them into blocks suitable for the food material inlet. Remove hard seeds or shells or thick skins of the fruits and vegetables, if any, first.
What is the eleventh step for installing the product for juicing?
Activate the switch, start working with working time ≤ 1 min.
What is the twelfth step for installing the product for juicing?
Put the prepared fruit and vegetable in the feeding port.
What is the thirteenth step for installing the product for juicing?
Push the blocks of fruit and vegetable gently through the feeding port with pushing rod. Too excessive force will affect the juicing effect. Never put your fingers or other objects inside the feeding port! Disconnect the power and clean the pomace cup when the pomace or juice cup is filled.
What is the fourteenth step for installing the product for juicing?
When there is no longer juice flowing via the juice outlet after good material processing, make the switch off, disconnect the power supply and take the juice cup from the juice nozzle after the motor and the juice strainer have both stopped running. Drink the juice at once, otherwise its taste and nutrition will be influenced after some time of exposure in air.
What should you do with the juice cup when the motor and juicing screen has completely stopped?
Take the juice cup away from the outlet nozzle when the motor and juicing screen has completely stopped.
What is the function of the foam baffle attached to the juice cup?
The foam baffle attached to juice cup may help you with a cup of foam-less juice. The baffle may be neglected if the juice with foam is required.
What should you do before cleaning the product?
Make the power switch off before cleaning the product.
When should you clean the product?
Clean the product promptly after use.
How should you clean the exterior of the main unit?
The exterior of the main unit of the product may be wiped by wet cloth. Do not place the main unit of the product into water or other liquids, or flush it with water or other liquids.
Where should you store the product?
Put the product in a dry place without direct ultraviolet rays.
What should you make sure of before storing the product?
Make sure the product is clean and dry before keeping it.
What is the first step for cleaning the detachable parts?
Take down the pushing rod.
What is the second step for cleaning the detachable parts?
Pull open the pull rod from right direction and take off the header.
What is the third step for cleaning the detachable parts?
Remove the juice strainer and the middle ring in order.
What is the fourth step for cleaning the detachable parts?
Clean with water the pomace cup, middle ring, juicing screen, and juice cup successively.
What is the rated voltage?
The rated voltage is 120V~.
What is the rated power?
The rated power is 400W.
What is the rated frequency?
The rated frequency is 60Hz.
What is the maximum continual juicing time?
The maximum continual juicing time is ≤ 1 min.
What is the time interval between juicing cycles?
The time interval between juicing cycles is ≥ 2 min.
What type of electric appliance is this product?
As an electric appliance of class II, the product needs no grounding device.
What should you do if the product does not run after the power supply is connected and the switch is on?
- Install the middle ring correctly; 2. Install the top cover correctly; or 3. Replace the top cover.
Is a bad smell from the motor normal in the first few uses?
If the bad smell still exists after the product has been used for several times, have the product tested by a near service center.
What should you do if the product stops automatically in use?
- Check whether the voltage is too low; 2. Disconnect the power supply and remove the surplus food materials; 3. Gently push the pushing rod; or 4. Stop the product and start it again 20 to 30 minutes later.
What should you do if there are many residues in the juice?
- Replace the juice strainer; or 2. Clean the middle ring.
What should you do if the product has abnormal vibration or big noise?
- Install the juice strainer correctly; 2. Place the product steadily or install the foot pad correctly; 3. Check whether the voltage is too high; or 4. Disconnect the power supply and remove the surplus food materials.
What should you do if there is a little juice?
- Clean the middle ring; or 2. Gently push the pushing rod.
What should you do if the cutter holder is seized?
Disconnect the power supply, take out the food materials and cut them into smaller blocks.
What should you do for other faults not listed in the table?
For other faults, contact customer service or have the product repaired by a designated service center. Do not dismantle or repair the product yourself.
CLICK HERE TO DOWNLOAD AICOK AMR516 (01) PDF MANUAL
how do I remove the strainer?
Page 8-9 (Chapter 4 Maintenance) of this manual shows you how to start and complete the disassemble process including removing the strainer.