Free English AEG FSK32610Z (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD AEG FSK32610Z (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What are the main components of the AEG FSK32610Z dishwasher?
The main components of the AEG FSK32610Z dishwasher are:
1. Upper spray arm
2. Lower spray arm
3. Filters
4. Rating plate
5. Salt container
6. Air vent
7. Rinse aid dispenser
8. Detergent dispenser
9. Cutlery basket
10. Lower basket
11. Upper basket
What are the functions of the buttons on the control panel of the AEG FSK32610Z?
The control panel of the AEG FSK32610Z has the following functions:
1. **On/off button / Reset button:** Turns the appliance on or off, and resets the current settings.
2. **Programme indicators:** Lights that indicate which programme is selected or running.
3. **Indicators:** Lights for salt, rinse aid, and the drying phase.
4. **Programme button:** Used to select a washing programme.
5. **Delay button:** Used to set a delay start for the programme.
What do the indicators on the control panel of the AEG FSK32610Z mean?
| Indicator | Description |
|---|---|
| SSS (Drying phase indicator) | It is on when you select a programme with the drying phase. It flashes when the drying phase operates. |
| S (Salt indicator) | It is on when the salt container needs refilling. It is always off while the programme operates. |
| ✽ (Rinse aid indicator) | It is on when the rinse aid dispenser needs refilling. It is always off while the programme operates. |
What programmes are available on the AEG FSK32610Z dishwasher?
The following programmes are available on the AEG FSK32610Z:
| Programme | Type of load | Degree of soil | Programme phases |
|---|---|---|---|
| ECO | Crockery, Cutlery, Pots, Pans | Normal, Lightly dried-on | Prewash, Wash 50 °C, Intermediate rinse, Final rinse 60 °C, Drying, AirDry |
| 160 min | Crockery, Cutlery, Pots, Pans | Normal to heavy, Dried-on | Prewash, Wash 60 °C, Intermediate rinse, Final rinse 60 °C, Drying, AirDry |
| 90 min | Crockery, Cutlery, Pots, Pans | Normal, Lightly dried-on | Wash 60 °C, Intermediate rinse, Final rinse 55 °C, Drying, AirDry |
| 30 min | Crockery, Cutlery | Fresh | Wash 50 °C, Intermediate rinse, Final rinse 50 °C, AirDry |
| Prewash Symbol | All types of loads | All degrees of soil | Prewash |
The ECO programme offers the most efficient use of water and energy consumption for crockery and cutlery with normal soil. It is the standard programme for test institutes.
With the Prewash programme, you can quickly rinse off food remains from dishes and prevent odours forming in the appliance. Do not use detergent with this programme.
What are the typical consumption values for the AEG FSK32610Z programmes?
| Programme | Water (l) | Energy (kWh) | Duration (min) |
|---|---|---|---|
| ECO | 9.9 | 0.920 / 0.936 | 227 |
| 160 min | 11.1 – 13.6 | 1.052 – 1.285 | 160 |
| 90 min | 9.6 – 11.7 | 0.886 – 1.083 | 90 |
| 30 min | 9.2 – 11.2 | 0.556 – 0.680 | 30 |
| Prewash Symbol | 3.4 – 4.2 | 0.012 – 0.015 | 15 |
Note: The pressure and the temperature of the water, the variations of the mains supply, the options, the quantity of dishes and the degree of soil can change the values. Values for programmes other than ECO are indicative only.
How do I enter user mode on my AEG FSK32610Z to change settings?
To enter user mode on your AEG FSK32610Z:
1. Make sure the appliance is in programme selection mode (the ECO indicator flashes).
2. Press and hold the programme button until the indicator ECO flashes and the indicators for 90 min and 30 min are on.
In user mode, you can adjust settings such as water softener level, rinse aid notification, acoustic signals, and AirDry activation.
How do I set the water softener level on my AEG FSK32610Z?
First, determine your local water hardness. Your local water authority can advise you on this. Then, use the table below to find the correct level for your AEG FSK32610Z.
| German degrees (°dH) | French degrees (°fH) | mmol/l | Clarke degrees | Water softener level |
|---|---|---|---|---|
| 47 – 50 | 84 – 90 | 8.4 – 9.0 | 58 – 63 | 10 |
| 43 – 46 | 76 – 83 | 7.6 – 8.3 | 53 – 57 | 9 |
| 37 – 42 | 65 – 75 | 6.5 – 7.5 | 46 – 52 | 8 |
| 29 – 36 | 51 – 64 | 5.1 – 6.4 | 36 – 45 | 7 |
| 23 – 28 | 40 – 50 | 4.0 – 5.0 | 28 – 35 | 6 |
| 19 – 22 | 33 – 39 | 3.3 – 3.9 | 23 – 27 | 5 (Factory setting) |
| 15 – 18 | 26 – 32 | 2.6 – 3.2 | 18 – 22 | 4 |
| 11 – 14 | 19 – 25 | 1.9 – 2.5 | 13 – 17 | 3 |
| 4 – 10 | 7 – 18 | 0.7 – 1.8 | 5 – 12 | 2 |
| <4 | <7 | <0.7 | <5 | 1 (Do not use salt at this level) |
To set the water softener level:
1. Make sure the appliance is in user mode.
2. Wait until the indicator SSS starts to flash, the indicator ECO continues to flash and the remaining indicators are off. The number of flashes corresponds to the current level (e.g., 5 flashes + pause + 5 flashes = level 5).
3. Press the programme button repeatedly to change the setting. Each press increases the level number. After level 10, it starts again from level 1.
4. Press the on/off button to confirm the setting.
How can I activate or deactivate the rinse aid empty notification on my AEG FSK32610Z?
To change the setting for the rinse aid empty notification on your AEG FSK32610Z:
1. Make sure the appliance is in user mode.
2. Press the programme button immediately. The indicator for 160 min starts to flash.
3. Wait until the 160 min indicator continues to flash and the remaining programme indicators are off.
4. The SSS indicator shows the current setting:
– SSS is on = Rinse aid empty notification is on.
– SSS is off = Rinse aid empty notification is off.
5. Press the programme button to change the setting.
6. Press the on/off button to confirm the setting.
How do I activate the acoustic signal for the end of a programme on the AEG FSK32610Z?
To activate the acoustic signal that sounds when a programme is complete:
1. Make sure the appliance is in user mode.
2. Press the programme button twice. The indicator for 90 min starts to flash.
3. Wait until the 90 min indicator continues to flash and the remaining programme indicators are off.
4. The SSS indicator shows the current setting:
– SSS is off = The acoustic signal is off.
– SSS is on = The acoustic signal is on.
5. Press the programme button to change the setting.
6. Press the on/off button to confirm the setting.
What is the AirDry function on the AEG FSK32610Z and how can I deactivate it?
The AirDry function on your AEG FSK32610Z improves drying results with less energy consumption. During the drying phase, the door opens automatically and remains ajar. This function is automatically activated with all programmes except Prewash.
To deactivate the AirDry function:
1. Make sure the appliance is in user mode.
2. Press the programme button three times. The indicator for 30 min starts to flash.
3. Wait until the 30 min indicator continues to flash and the remaining programme indicators are off.
4. The SSS indicator shows the current setting:
– SSS is off = AirDry is off.
– SSS is on = AirDry is on.
5. Press the programme button to change the setting.
6. Press the on/off button to confirm the setting.
What are the steps to follow before the first use of the AEG FSK32610Z?
Before using your AEG FSK32610Z for the first time, follow these steps:
1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Start a programme to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not put dishes in the baskets.
After starting the programme, the appliance recharges the resin in the water softener for up to 5 minutes. The washing phase starts only after this procedure is complete.
How do I fill the salt container in my AEG FSK32610Z?
To fill the salt container:
1. Turn the cap of the salt container counterclockwise and remove it.
2. Put 1 litre of water in the salt container (only for the first time).
3. Fill the salt container with 1 kg of dishwasher salt (until it is full). Use the supplied funnel.
4. Carefully shake the funnel by its handle to get the last granules inside.
5. Remove the salt around the opening of the salt container.
6. Turn the cap of the salt container clockwise to close it.
CAUTION: Water and salt can come out of the salt container when you fill it. After you fill the salt container, immediately start a programme to prevent corrosion.
How do I fill the rinse aid dispenser in my AEG FSK32610Z?
To fill the rinse aid dispenser:
1. Press the release button (D) to open the lid (C).
2. Fill the dispenser (A) until the rinse aid reaches the marking “MAX”.
3. Remove any spilled rinse aid with an absorbent cloth to prevent excessive foam formation.
4. Close the lid. Make sure that the release button locks into position.
You can also adjust the released quantity of rinse aid using the selector (B) between position 1 (lowest quantity) and position 4 or 6 (highest quantity).
How do I start a programme on the AEG FSK32610Z?
To set and start a programme:
1. Keep the appliance door ajar.
2. Press the on/off button to activate the appliance. Make sure it is in programme selection mode.
3. Press the programme button repeatedly until the indicator of the programme you want to select starts flashing.
4. Close the appliance door to start the programme.
How can I start my AEG FSK32610Z with a delay?
To start a programme with a delay start:
1. Set a programme.
2. Press the delay button to delay the start of the programme by 3 hours. The indicator 3h is on.
3. Close the appliance door to start the countdown.
During the countdown, it is not possible to change the programme. When the countdown is complete, the programme starts.
How do I cancel a delay start or a running programme on my AEG FSK32610Z?
To cancel the delay start or a running programme:
Press and hold the programme button for 3 seconds until the appliance is in programme selection mode.
If cancelling a running programme, make sure that there is detergent in the detergent dispenser before you start a new programme.
What should I do if I want to stop using multi-tablets in my AEG FSK32610Z?
If you want to switch from multi-tablets to separate detergent, salt, and rinse aid, complete the following steps:
1. Set the highest level of the water softener.
2. Make sure that the salt and rinse aid containers are full.
3. Start the shortest programme with a rinsing phase. Do not add detergent and do not put dishes in the baskets.
4. When the programme is complete, adjust the water softener according to the water hardness in your area.
5. Adjust the released quantity of rinse aid.
6. Activate the rinse aid empty notification.
How should I load and unload the baskets in the AEG FSK32610Z?
For best results when loading and unloading your AEG FSK32610Z:
Loading:
– Always use the whole space of the baskets.
– Only wash dishwasher-safe items.
– Put hollow items (cups, glasses, pans) with the opening facing downwards.
– Make sure that glasses do not touch each other.
– Put light items in the upper basket and ensure items do not move freely.
– Put cutlery and small items in the cutlery basket.
– Make sure that the spray arms can move freely before you start a programme.
Unloading:
1. Let the tableware cool down before you remove it from the appliance. Hot items can be easily damaged.
2. First remove items from the lower basket, then from the upper basket.
How do I clean the filters of my AEG FSK32610Z?
The filter system is made of 3 parts (A, B, C). To clean them:
1. Turn the filter (B) counterclockwise and remove it.
2. Remove the filter (C) out of filter (B).
3. Remove the flat filter (A).
4. Wash the filters thoroughly under running water.
5. Make sure that there are no residues of food or soil in or around the edge of the sump.
6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides.
7. Reassemble the filters (B) and (C).
8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks.
How do I clean the spray arms on the AEG FSK32610Z?
We recommend cleaning the lower spray arm regularly to prevent soil from clogging the holes.
1. To remove the lower spray arm, pull it upwards.
2. Wash the spray arm under running water. Use a thin pointed tool, e.g. a toothpick, to remove particles of soil from the holes.
3. To install the spray arm back, press it downwards.
What should I do if my AEG FSK32610Z will not activate?
If you cannot activate the appliance, try the following:
– Make sure that the mains plug is connected to the mains socket.
– Make sure that there is no damaged fuse in the fuse box.
Why won’t a programme start on my AEG FSK32610Z?
If the programme does not start:
– Make sure that the appliance door is closed.
– If the delay start is set, cancel the setting or wait for the end of the countdown.
– The appliance may be recharging the resin inside the water softener. The duration of this procedure is approximately 5 minutes. Wait for it to complete.
What does it mean when my AEG FSK32610Z doesn’t fill with water and the SSS indicator flashes once?
If the appliance does not fill with water, the SSS indicator flashes 1 time intermittently, and an acoustic signal sounds 1 time intermittently, check the following:
– Make sure that the water tap is open.
– Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority.
– Make sure that the water tap is not clogged.
– Make sure that the filter in the inlet hose is not clogged.
– Make sure that the inlet hose has no kinks or bends.
What should I do if my AEG FSK32610Z is not draining and the SSS indicator flashes twice?
If the appliance does not drain the water, the SSS indicator flashes 2 times intermittently, and an acoustic signal sounds 2 times intermittently, perform these checks:
– Make sure that the sink spigot is not clogged.
– Make sure that the interior filter system is not clogged.
– Make sure that the drain hose has no kinks or bends.
The anti-flood device is on and the SSS indicator is flashing 3 times on my AEG FSK32610Z. What do I do?
If the anti-flood device is on, the SSS indicator flashes 3 times, and an acoustic signal sounds 3 times, take these steps:
– Close the water tap.
– Make sure that the appliance is correctly installed.
– Make sure the baskets are loaded as instructed in the user manual.
What is the problem if the SSS indicator on my AEG FSK32610Z flashes 4, 5, 6, or 12 times?
These alarm codes indicate specific malfunctions:
– **4 flashes:** Malfunction of the water level detection sensor. Make sure the filters are clean, then switch the appliance off and on.
– **5 flashes:** Malfunction of the wash pump or the drain pump. Switch the appliance off and on.
– **6 flashes:** The temperature of the water inside the appliance is too high or there is a malfunction of the temperature sensor. Make sure the inlet water temperature does not exceed 60°C, then switch the appliance off and on.
– **12 flashes:** Technical malfunction of the appliance. Switch the appliance off and on.
What does it mean if the water level inside my AEG FSK32610Z is too high and the SSS indicator flashes 15 times?
If the water level is too high and the SSS indicator flashes 15 times intermittently:
– Switch the appliance off and on.
– Make sure that the filters are clean.
– Make sure that the outlet hose is installed at the right height above the floor. Refer to the installation instructions.
Why do my dishes have poor washing or drying results in the AEG FSK32610Z?
For poor washing results:
– Refer to “Daily use”, “Hints and tips” and basket loading leaflet.
– Use more intensive washing programmes.
– Clean spray arm jets and filter. Refer to “Care and Cleaning”.
For poor drying results:
– Tableware has been left for too long inside a closed appliance.
– There is no rinse aid or the dosage of rinse aid is not enough. Set the rinse aid dispenser to a higher level.
– Plastic items may need to be towel dried.
– For the best drying performance activate AirDry.
– We recommend to always use rinse aid, even in combination with multi-tablets.
Why are there whitish streaks, bluish layers, stains, or dry water drops on my glasses and dishes from the AEG FSK32610Z?
For whitish streaks or bluish layers:
– The release quantity of rinse aid is too much. Adjust the rinse aid level to a lower level.
– The quantity of detergent is too high.
For stains and dry water drops:
– The released quantity of rinse aid is not sufficient. Adjust the rinse aid level to a higher level.
– The quality of the rinse aid can be the cause.
What should I do if detergent residue is left in the dispenser of my AEG FSK32610Z after a cycle?
If there are residues of detergent in the dispenser at the end of the programme:
– The detergent tablet got stuck in the dispenser and therefore was not completely washed away by water.
– Water cannot wash away the detergent from the dispenser. Make sure that the spray arm is not blocked or clogged.
– Make sure that items in the baskets do not impede the lid of the detergent dispenser from opening.
What are the technical specifications of the AEG FSK32610Z dishwasher?
| Dimensions | Width / height / depth (mm) | 596 / 818 – 898 / 550 |
| Electrical connection | Voltage (V) | 220 – 240 |
| Frequency (Hz) | 50 | |
| Water supply pressure | Min. / max. bar (MPa) | 0.5 (0.05) / 8 (0.8) |
| Water supply | Cold water or hot water | max 60 °C |
| Capacity | Place settings | 13 |
| Power consumption | Left-on mode (W) | 5.0 |
| Off-mode (W) | 0.50 |
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
CLICK HERE TO DOWNLOAD AEG FSK32610Z (01) PDF DOCUMENT