ADJ 18P HEX (01) PDF Document

Every ADJ 18P HEX has been thoroughly tested and shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all accessories necessary to operate the unit have arrived intact. In the case damage has been found or parts are missing, please contact customer support for further instructions. Do not return this unit to your dealer without first contacting customer support.

• Multi-Colors

• Five Operating Modes

• Electronic Dimming 0-100%

• 5 Dimmer Curves

• Built in Microphone

• DMX-512 protocol

• 3-Pin DMX Connection

• 4 DMX Modes: 6 Channel Mode, 7 Channel Mode, 8 Channel Mode, & 12 Channel Mode.

• Dotz Par RF compatible (Not Included)

• Power Cord Daisy Chain

The unit should be mounted using a mounting clamp (not provided), affixing it to the mounting bracket that is provided with the unit. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times the unit’s weight. Also, always use a safety cable that can hold 12 times the weight of the unit when installing the fixture.

The equipment must be installed by a professional, and it must be installed in a place where it is out of the reach of people’s grasp.

• To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user serviceable parts inside.

• Never operate this unit when its cover is removed.

• Never plug this unit in to a dimmer pack.

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only; use of this product outdoors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in a safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to the point they exit from the unit.

• The fixture should be cleaned only as recommended by the manufacturer.

• The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the appliance.

C. The appliance has been exposed to rain or water.

D. The appliance does not appear to operate normally or exhibits a marked change in performance.

Power Supply: The ADJ 18P Hex contains an automatic voltage switch, which will auto sense the voltage when it is plugged into the power source. With this switch there is no need to worry about the correct power voltage; this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of different manufacturers to be linked together and operate from a single controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation): The 18P Hex can be controlled via DMX protocol. The 18P Hex has 4 DMX channel modes. Your unit and your DMX controller require a standard 3-pin XLR connector for data input and data output. We recommend Accu-Cable DMX cables. If you are making your own cables, be sure to use standard 110-120 Ohm shielded cable (This cable may be purchased at almost all pro lighting stores). Your cables should be made with a male and female XLR connector on either end of the cable. Also remember that DMX cable must be daisy chained and cannot be split. When making your own cables, do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior.

Line Termination: When longer runs of cable are used, you may need to use a terminator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator will decrease the possibilities of erratic behavior.

Some manufacturers use 5-pin DMX-512 data cables for DATA transmission in place of 3-pin. 5-pin DMX fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables into a 3-pin line a cable adaptor must be used. The chart below details a proper cable conversion.

The control panel will lock itself after 30 seconds if nothing is pressed. To unlock the control panel, press the MODE button for 3 seconds.

The 18P Hex has five operating modes:

• DMX control mode – This function will allow you to control each individual fixture’s traits with a standard DMX 512 controller.

• RGBWA + UV Mode – Choose one of the six colors to remain static or adjust the intensity of each color to make your own color.

• Sound-Active mode – The unit will react to sound, chasing through the built-in programs. The sound sensitivity is adjustable.

• Program Mode – There are 7 built-in programs to choose from. Color change and color fade speeds are adjustable.

• Static Color Mode – There are 63 colors to choose from.

Operating through a DMX controller gives the user the freedom to create their own programs tailored to their own individual needs. The 18P Hex has 4 DMX modes: 6 Channel mode, 7 Channel mode, 8 Channel mode, and a 12 Channel mode.

1. This function will allow you to control each individual fixture’s traits with a standard DMX 512 controller.

2. To run your fixture in DMX mode press the MODE button until “AXXX” is displayed. “XXX” represents the current displayed address. Use the UP or DOWN buttons to select your desired DMX address, then press the ENTER button to select your DMX Channel mode.

3. Use the UP or DOWN buttons to scroll through the DMX Channel modes. The Channel modes are listed below:

• To run the 6 Channel Mode, press the MODE button until “CH06” is displayed. This is the 6 Channel DMX Mode.

• To run the 7 Channel Mode, press the MODE button until “CH07” is displayed. This is the 7 Channel DMX Mode.

• To run the 8 Channel Mode, press the MODE button until “CH08” is displayed. This is the 8 Channel DMX Mode.

• To run the 12 Channel Mode, press the MODE button until “CH12” is displayed. This is the 12 Channel DMX Mode.

4. After you have chosen your desired DMX Channel mode plug in the fixture via the XLR connections to any standard DMX controller.

In this mode you can adjust the individual colors to make your desired color.

1. Plug the fixture in and press the MODE button until “rXXX” is displayed. You are in Red dimming mode. Press the UP and DOWN buttons to adjust the intensity. After you have finished adjusting the intensity, or if you would like to skip to the next color, press the ENTER button.

2. When “GXXX” is displayed you are in Green dimming mode. Press the UP and DOWN buttons to adjust the intensity.

3. When “bXXX” is displayed you are in Blue dimming mode. Press the UP and DOWN buttons to adjust the intensity.

4. When “uXXX” is displayed you are in White dimming mode. Press the UP and DOWN buttons to adjust the intensity.

5. When “AXXX” is displayed you are in Amber dimming mode. Press the UP and DOWN buttons to adjust the intensity.

6. When “UXXX” is displayed you are in UV dimming mode. Press the UP and DOWN buttons to adjust the intensity.

1. Plug the fixture in and press the MODE button until “C-XX” is displayed. “XX” is the color number currently displayed.

2. There are 63 colors to choose from. Select your desired color by pressing the UP and DOWN buttons.

In this mode you can choose 1 of 7 programs to run. The fade speed and program speed are both adjustable.

1. Plug the fixture in and press the MODE button until “P-XX” is displayed. “XX” is the current program number displayed.

2. Use the UP or DOWN button to find your desired program.

3. Press the ENTER button to adjust the fade speed, “00” being the slowest, “30” the fastest.

4. Press the ENTER button again to adjust the color change speed, “00” being the slowest, “30” the fastest.

The available programs are:

• P-01 – 63 Color Change with Fade Control

• P-02 – 63 Color Change No Fade

• P-03 – 63 Color Fade

• P-04 – 6 Color Change No Fade

• P-05 – 6 Color Change With Fade

• P-06 – 63 Color Fade with Sound Control

• P-07 – 63 Color Change with Sound Control

In this mode the 18P Hex will react to sound, and chase through the different colors.

1. Plug the fixture in and press the MODE button until “SoXX” is displayed. “XX” represents the sound sensitivity level. Use the UP and DOWN buttons to adjust the sensitivity. “00” is the lowest sensitivity, “30” is the highest.

This function is used to activate and deactivate the RF Remote Control. When this function is activated you can control the fixture using the Dotz Par RF remote.

1. Plug the fixture in and press the MODE button until “rFXX” is displayed. “XX” represents either “on” or “oFF”.

2. Press the UP or DOWN buttons to either activate the remote function (On) or deactivate it (Off).

This is used to set the dimmer curve used with DMX mode.

1. Plug the fixture in and press the MODE button until the DMX address is displayed.

2. Press the ENTER button until “dCXX” is displayed. This is the dimmer setting. “XX” represents the current dimming mode.

3. Use the UP and DOWN buttons to find your desired dimmer curve. Press SET UP when you are finished.

• dC00 – Standard

• dC01 – Stage

• dC02 – TV

• dC03 – Architectural

• dC04 – Theater

This mode is used as a precaution mode, that in case the DMX signal is lost, the operating mode chosen in this setup is the running mode the fixture will go into when the DMX signal is lost. You can also set this as the operating mode you would like the unit to return to when power is applied.

1. Press the MODE button until the DMX address is displayed. Press the ENTER button until either “Soun”, “HOLD”, or “bLC” is displayed.

2. Use the UP or DOWN buttons to find the mode you want in case of power loss or DMX loss.

• “bLC” (Blackout) – If the DMX signal is lost or interrupted, the unit will automatically go into stand by mode.

• “HOLD” (Last State) – If the DMX signal is lost or interrupted, the fixture will stay in the last DMX set up. If power is applied and this mode is set, the unit will automatically go into the last DMX set up.

• “Soun” (Sound Active) – If the DMX signal is lost or interrupted, the unit will automatically go into sound active mode.

3. Find your desired setting and press ENTER. Your setting will be saved automatically.

This function allows you to link units together to run in a Master-Slave mode. In Master-Slave operation one unit will act as the controlling unit and the others will react to the controlling unit’s built-in programs. Any unit can act as a Master or as a Slave; however, only one unit can be programmed to act as the “Master.”

Master-Slave Connections and Settings:

1. Daisy chain your units via the XLR connector on the rear of the unit. Use standard XLR data cables to link your units together. Remember that the Male XLR connector is the input and the Female XLR connector is the output. The first unit in the chain (master) will use the female XLR connector only. The last unit in the chain will use the male XLR connector only.

2. Set the “Master” unit to your desired mode of operation.

3. Connect the first “Slave” unit to the “Master.”

4. On the “Slave” unit press the MODE button until “SLAv” is displayed. The “Slave” unit will now follow the “Master”.

With this feature you can connect the fixtures to one another using the powerCON input and output sockets. The quantity that can be connected is 4 fixtures maximum for 120V and 8 fixtures maximum for 240V. After the maximum number of fixtures has been reached, you will need to use a new power outlet.

NOTE: USE CAUTION WHEN POWER LINKING OTHER FIXTURES TO THE 18P HEX. POWER CONSUMPTION OF OTHER LIGHTING FIXTURES WILL VARY. ALWAYS CHECK THE MAX AMP OUT RATING OF EACH FIXTURE!

The Dotz Par RF remote (sold separately) has many different functions which allow you to control the 18P HEX from a distance of 82 feet (25 meters). To use the remote, the RF feature must first be activated on the fixture.

• BLACKOUT – Press to blackout the fixture.

• FADE – Press to activate Fade Program.

• COLOR – Press to activate Static Color Mode.

• PROGRAMS – Press to activate Built-In Program Mode.

• SOUND ACTIVE – Press to activate Sound Active Mode.

• (+) (-) – Press to scroll/adjust programs, colors, and speed.

6 Channel – DMX Values & Functions

7 Channel – DMX Values & Functions

8 Channel – DMX Values & Functions

12 Channel – DMX Values & Functions

Note: When Channel 10 is between the values of 21-80, Channel 11 will control the color change speed and color fade speed.

Note: When Channel 10 is between the values of 81-140, Channel 11 will control the sound sensitivity.

Disconnect the unit from its power source. Remove the power cord from the unit. Once the cord has been removed, use a flat head screwdriver to unscrew the fuse holder. Once unscrewed, remove the fuse holder and replace the bad fuse with a new fuse. Replace the fuse holder and screw the holder so that it is secure.

Listed below are a few common problems the user may encounter, with solutions.

Unit not responding to DMX:

1. Check that the DMX cables are connected properly and are wired correctly (pin 3 is “hot”; on some other DMX devices pin 2 may be ‘hot’). Also, check that all cables are connected to the right connectors; it does matter which way the inputs and outputs are connected.

Unit does not respond to sound:

1. Quiet or high pitched sounds will not activate the unit.

2. Make sure that Sound Active mode is activated.

Due to fog residue, smoke, and dust, cleaning the internal and external optical lenses must be carried out periodically to optimize light output.

1. Use normal glass cleaner and a soft cloth to wipe down the outside casing.

2. Clean the external optics with glass cleaner and a soft cloth every 20 days.

3. Always be sure to dry all parts completely before plugging the unit back in.

Cleaning frequency depends on the environment in which the fixture operates (i.e. smoke, fog residue, dust, dew).