ACTIONAIR LC7-2G (01) PDF MANUAL

ACTIONAIR LC7-2G (01) PDF SUMMARY:

How do I turn the air conditioner on or off?

Press the Power On/Off button once to turn the air conditioner on, and press it again to turn it off. The system will restart using the last settings and operating mode, such as the set temperature, AUTO mode, and HIGH fan speed. The display will show the Set Temperature, Fan Speed, Fan Mode, and Mode of Operation.

---

How do I adjust the set temperature?

Press the Temperature-Up Setting button to increase the room temperature or the Temperature-Down Setting button to decrease it. The set temperature is adjustable between 16°C and 30°C in 0.5°C increments. The set temperature can be adjusted even when the system is off. There is no set temperature displayed during Fan-Only Mode.

---

How do I change the operating mode?

The operating modes can be changed by pressing the Operation MODE button until the desired mode appears on the display. Fan-Only, Cooling, and Heating modes are available. For all modes of operation, LOW, MED, HIGH, LOW CONT, MED CONT and HIGH CONT fan speeds can only be selected if the 3-Speed Fan setting option is selected. Otherwise, MED and MED CONT are available for 1-Speed Fan. When in Fan-Only Mode, LOW CONT, MED CONT and HIGH CONT will not be available. When the system is ON, the Indoor Fan can run continuously, indicated by the CONT indicator on the LCD. This is generally preferred during the Cooling Mode to ensure maximum air circulation. When set to LOW, MED, or HIGH, the fan will cycle with the compressor operation according to set point and room temperatures.

---

How do I use the Fan-Only operation?

Press the MODE button until FAN appears on the display. Adjust the indoor fan speed (LOW, MED, and HIGH) by pressing the FAN button until the desired speed is reached (only for 3-speed fan).

---

How do I use the Cooling operation?

Press the MODE button until COOL appears on the display. Set the desired temperature using the Temperature-Up or Temperature-Down buttons. Adjust the desired indoor fan speed by pressing the FAN button. Available settings are: LOW, MED, HIGH, CONT LOW, CONT MED, and CONT HIGH.

---

How do I use the Heating operation?

Press the MODE button until HEAT appears on the display. Set the desired temperature using the Temperature-Up or Temperature-Down buttons. Adjust the desired indoor fan speed by pressing the FAN button. Available settings are: LOW, MED, HIGH, CONT LOW, CONT MED, and CONT HIGH. Note: Setting the indoor fan speed to continuous mode can cause cool drafts when operating the system on heating mode during compressor off cycles.

---

How do I set the system to Auto Operation?

Press the MODE button until AUTO appears on the display. Set the desired temperature by pressing either the up or down buttons. Adjust the desired Indoor Fan speed by pressing the FAN button. Available settings are: LOW, MED, HIGH, CONT LOW, CONT MED AND CONT HIGH.

---

What should I know about setting the indoor fan speed to continuous mode?

Setting the indoor fan speed to continuous mode can cause cool drafts when operating the system on a heating cycle during compressor off cycles.

---

How do I set an OFF Timer?

Press the TIMER button to enter the timer menu. The system must be On to set an OFF timer. Press the up or down buttons to select the desired time for the system to remain operating before turning OFF. The maximum adjustable timer hours are 24 with 0.5-hour (30-minute) adjustable increments. Three seconds after the last press of the up or down buttons, the display will go back to the main screen and the OFF Timer countdown will start. The unit will turn OFF after the timer has expired.

---

How do I know if a timer is active?

If a timer is active, a TIMER indicator will be displayed.

---

How do I cancel an OFF Timer?

To cancel the Off Timer, press the power button and the TIMER indicator will disappear.

---

How do I set an ON Timer?

Press the TIMER button to enter the timer menu. The system’s status must be Off to set an ON Timer. Press the up or down buttons to select the desired time for the system to turn On. The maximum adjustable timer hours are 24 with 0.5-hour (30-minute) adjustable increments. Three seconds after the last press of the up or down buttons or simply press TIMER, the display will go back to the main screen and the On Timer countdown will start. The unit will turn On after the timer has expired.

---

How do I cancel an ON Timer?

To cancel the ON Timer, press the power button.

---

How do I adjust the LCD backlight level?

Press and continue to hold the REPEAT button. Press the up or down buttons to adjust the backlight level. To brighten the backlight, press the up button. To dim the backlight, press the down button. Release the buttons at the desired level of LCD brightness. The lock symbol will appear for 3 seconds showing that the backlight level is set.

---

How do I permanently turn on the LCD Backlight?

Press and hold the REPEAT button for 4 seconds. When the Lock symbol appears, release the REPEAT button and the backlight will remain illuminated. To return to default settings, repeat steps 1 and 2. By default, the LCD Backlight is programmed to turn off 15 seconds after a button has been last pressed.

---

How do I turn on the ON/OFF button backlight?

The Wall Control status must be On before operating this procedure. By default, the ON/OFF button backlight is On. Press and hold the REPEAT button. Press and release the On/Off button, along with the REPEAT button. The Lock symbol will appear for 3 seconds showing that the On/Off button backlight is set. The On/Off backlight will remain lit.

---

How do I turn off the ON/OFF button backlight?

Press and hold the REPEAT button. Press and release the On/Off button, along with the REPEAT button. The Lock symbol will appear for 3 seconds showing that the On/Off button backlight is set. The On/Off backlight will turn OFF.

---

What should I know about the Program Menu?

The Program Menu has a 60-second inactive timeout, once expired, the display will return to the home screen. Program Menu 01 (7-Day Programmable Function), 02 (Clock) and 03 (Temperature Set back) can only be set via Wall Control 1 (C-1). Wall Control 2 and 3 (C-2 and C-3) will skip these Menus and directly proceed at Menu 04.

---

What is the 7-Day Programmable Function?

The 7-Day Time clock feature of the control allows you to set the air conditioning system to Turn-ON and Turn-OFF at different times for each day of the week. Each day can have 2-Programmed Events. Each event has an On and Off time. It’s important to ensure that the current day and time are set correctly before proceeding with programming. To reset any scheduled time clock events, press and hold the PROG and DISP buttons for 3 seconds.

---

Example of Time clock Operation:

	MON	TUE	WED	THU	FRI	SAT	SUN
EVENT 1 ON TIME	6:00am	6:00am	6:00am	6:00am	6:00am	7:00am	8:00am
EVENT 1 OFF TIME	10:00am	10:00am	10:00am	10:00am	10:00am	9:00am	11:00am
EVENT 2 ON TIME	4:00pm	4:00pm	4:00pm	4:00pm	1:00pm	-:–	-:–
EVENT 2 OFF TIME	10:00pm	10:00pm	10:00pm	10:00pm	11:00pm	-:–	-:–

---

How do I activate the 7-Day Time clock?

Press the PROG button to enter the program Menu. TIME CLOCK and PROG indicators will be illuminated on the screen. Press the PROG button to enter the time clock menu. By default, the time clock program is OFF. TIME CLOCK and PROG indicators are still illuminated. OFF indicator will be flashing on the screen. Press the up button to scroll from OFF to ON. Press the PROG button to accept the selection and re-activate the time clock. Press the EXIT button twice to go back to the main display screen. TIME CLOCK indicator will re-appear on the screen, indicating that the Time clock has been reactivated.

---

How do I set the Programmable Time Clock?

Press the PROG button to enter the program Menu. TIME CLOCK and PROG indicators will be illuminated on the screen. Press the PROG button to enter the time clock menu. The Time Clock program is currently On. TIME CLOCK and PROG indicators are still illuminated. ON indicator will be flashing on the screen. Press the PROG button (ON is selected) to program the time clock. TIME CLOCK, PROG, ON, EVENT 1, MON, and SET indicators and Time Fields will be shown on the screen. You can now set the Event 1 On time for Monday. Pressing the power button will enable or disable the Time Clock program. Press the up or down buttons to adjust the time in 15-minute increments. AM and PM will toggle after the 12th Hour.

---

How do I set the Event 1 Off time, Event 2 On time, and Event 2 Off time?

Press the PROG button to move to Event 1 Off time. Press the up or down buttons to adjust the time in 15-minute increments. Press the PROG button to move to Event 2 On time. Repeat the above step to program Event 2 On and Off time. Press the EXIT button at any time if no further changes to later Days/Events are required. Press the PROG button to move onto Event 1 On time of the following day, TUE. Repeat the above steps until you have programmed all the events you require. Otherwise, press the EXIT button twice to exit the Program Menu. TIME CLOCK display will show on the screen to indicate that it is active. If a button has not been pressed after 60 seconds, the control will exit the Time Clock program menu and return to the home screen. During a power failure, the control will retain the time and Time Clock settings.

---

How do I repeat a day’s events and times?

Proceed to the day you wish to copy the programmed events and times. SET, EVENT 1, TIME CLOCK, PROG, MON, and ON will be illuminated on the screen. The repeat function can only be applied to the succeeding day with programmed events. Press the PROG button until you reach the succeeding day, TUE, to paste the copied programmed events and times. Press the REPEAT button. You have now copied the previous day’s events into the current day displayed. Repeat the above steps for the remaining days where you wish to repeat the programmed events and times.

---

What are the limitations of setting Event ON and OFF times?

Event ON times can be set up to 11:45 PM of the current day. Event OFF times can be set to the following day up to 23 hours and 45 minutes after the ON time. If you program Event 1 past midnight, Event 2 will be automatically canceled.

---

How do I cancel an individual event?

Press the PROG button to enter the program Menu. TIME CLOCK and PROG indicators will be illuminated in the screen. Press the PROG button to enter the time clock menu. TIME CLOCK and PROG indicators are still illuminated. The ON indicator will be flashing on the screen. Press the PROG button (ON is selected) to program the time clock. TIME CLOCK, PROG, ON, EVENT 1, MON, and SET indicators and time fields will be shown on the screen. You can now set the Event 1 ON time for Monday. Continue pressing the PROG button to get to the desired event to cancel. Press the power button to delete the event. -:– will be displayed indicating the event is canceled. Repeat the above process to repeat other days’ events otherwise, press the EXIT button twice to exit the Program Menu. Canceling Event 1 will cancel both Event 1 and Event 2. Canceling Event 2 will only cancel Event 2.

---

How do I re-activate an individual event?

Press the PROG button to enter program Menu. TIME CLOCK and PROG indicators will be illuminated in the screen. Press the PROG button to enter the time clock menu. The Time Clock program is currently ON. TIME CLOCK and PROG indicators will still be illuminated, with the ON indicator flashing. Press the PROG button (ON is selected) to program the time clock. TIME CLOCK, PROG, ON, EVENT 1, MON, and SET indicators and time fields will be shown on the screen. You can now set the Event 1 On time for Monday.

---

How do I re-activate a desired event on the 7-Day Time Clock?

Continue pressing the PROG button to get to the desired event. Press the button to re-activate the event. The event’s On time will be displayed, indicating the event is re-activated. Press the EXIT button twice to exit Program Menu.

---

How do I deactivate the 7-Day Time Clock?

Press the PROG button to enter program Menu. TIME CLOCK and PROG indicators will be illuminated on the screen. Press the PROG button again to enter the time clock menu. The Time Clock program is currently ON. TIME CLOCK and PROG indicators are still illuminated, and the ON indicator will be flashing on the screen. Press the button to scroll through from ON to OFF. Press the PROG button to accept the selection and de-activate the time clock, then press the EXIT button once. TIME CLOCK indicators will disappear from the main screen, indicating that the Time clock has been de-activated.

---

How do I set the clock?

The system’s status must be On before performing these procedures. Press the PROG button to enter the program Menu. Press the or buttons to navigate to Program Menu 02. Press the PROG button to enter Program Menu 02. The display will show the clock display, and the Hour field and TIME will be blinking. Press the or buttons to adjust the Hour. AM / PM will adjust after the 12th hour. Press the PROG button to accept the desired hour. The Minute field will start blinking. Press the or buttons to adjust the Minutes. Press the PROG button to accept the desired minutes. The Day field will start blinking, and the Day indicator will be flashing, i.e., MON. Press the or buttons to adjust the Day. Press the PROG button to accept the desired Day. The screen will show the final selected time and day. Press the EXIT button twice to go back to the Main Screen.

---

What is the temperature set back feature?

The temperature set back feature will maintain the building temperature at a pre-determined and reasonable temperature closer to your chosen set temperature, thus giving you a big head start in achieving your comfortable temperature. Normally, the air conditioning system is turned off at unoccupied times or at night, which can result in the building temperature becoming quite hot (e.g., 30oC) or quite cold (e.g., 12oC). When you turn on the air conditioning system, it can take a long time to achieve a comfortable temperature (e.g., 23oC).

---

How do I activate the temperature set back feature?

The system must be turned off before performing these procedures. Press the PROG button to enter program Menu. Press the or buttons to navigate to Program Menu 03. Press the PROG button to enter Program Menu 03. The display will show the SET BACK indicator, and the OFF field will be blinking. Press the or buttons to scroll from OFF to ON. Press the PROG button to confirm the selection. Press the EXIT button three times to go back to the Main Screen.

---

How do I set the temperature set back?

The Set back mode Cool to and Heat to limits can only be adjusted from the temperature set back menu. If the unit’s setpoint (prior to Set back operation) is below the Heat to limit or higher than the Cool to limit, the unit’s setpoint will automatically become the new Set back limit. Press the PROG button to enter program Menu. Press the or buttons to navigate to Program Menu 03. Press the PROG button to enter Program Menu 03. The display will show the set back display and the ON field will be blinking. Press the PROG button to enter On Program Menu. Press the or buttons to change the COOL set back temperature. Press the PROG button to accept the COOL set back temperature. The next screen will show the HEAT set back temperature adjustment. Press the or buttons to change the HEAT set back temperature. Press the PROG button to accept the HEAT set back temperature. Press the EXIT button once to go back to the Main Screen.

---

What do the temperature set back screens display?

• H Set back: Heat To Set back limit
• C Set back: Cool To Set back limit
• U setpoint: Unit setpoint prior to unit turned off
• R temp: Room Temperature

The following table describes what is displayed on the LC7-2 during Set back operation:

Mode of Operation	LC7-2 Display
R temp ≤ H Set back	H Set back
H Set back < R temp ≤ C Set back	U setpoint Off
R temp > C Set back	C Set back
R temp < H Set back	Heating R temp
R temp > C Set back	Cooling R temp

NOTE:

• Indoor fan speed will operate to the last setting.
• The button backlight is always off under the set back mode when operation mode is heat or cool.

---

How do I deactivate the temperature set back?

Press the PROG button to enter the program Menu. Press the or buttons to navigate to Program Menu 03. Press the PROG button to enter Program Menu 03. The display will show set back display, and the ON field is blinking. Press the or buttons to toggle from ON to OFF. Press the PROG button to confirm the selection. Press the EXIT button once to go back to the Main Screen.

---

How do I activate mode lock?

Mode Lock will prevent the user from changing the mode of operation based on the previous mode being used. Mode Lock may be set independently on each wall controller connected. Ensure that the control is set to the mode you wish to lock to. Press the PROG button to enter the program Menu. Press the or buttons to navigate to Program Menu 04. Press the PROG button to enter Program Menu 04. Mode lock is Off by default. Press the or buttons to turn the Mode lock ON. Press the PROG button to accept the selection. Press the EXIT once to go back to the Main Screen. When the MODE button is pressed, the symbol will appear for 3 seconds, and the user won’t be able to change the mode.

---

How do I disable Mode Lock?

Follow the same steps to activate Mode Lock. However, in step 5, select OFF.

---

How do I activate the setpoint lock?

Setpoint Lock will prevent the user from changing the setpoint on the wall controller. Setpoint Lock may be set independently on each wall controller connected. Set the setpoint based on the desired target temperature. Press the PROG button to enter the program Menu. Press the or buttons to navigate to Program Menu 05. Press the PROG button to enter Program Menu 05. Setpoint lock is OFF by default. Press the or buttons to turn the setpoint lock ON. Press the PROG button to accept the selection. Press the EXIT button once to go back to the main screen. When the or buttons are pressed, the symbol will appear for 3 seconds, and the user will not be able to change the set temp.

---

How do I disable setpoint Lock?

Follow the same steps to activate Setpoint Lock. However, in step 5 select OFF.

---

How do I activate the fan speed lock?

Fan Speed Lock will prevent the user from changing the fan speed on the wall controller. Fan Speed Lock may be set independently on each wall controller connected. Set the required fan speed you wish to lock. Press the PROG button to enter Program Menu. Press the or buttons to navigate to Program Menu 06. Press the PROG button to enter Program Menu 06. Fan speed lock is Off by default. Press the or buttons to turn the fan lock ON. Press the PROG button to accept the selection. Press the EXIT button once to go back to the main screen. When the FAN button is pressed, the symbol will appear for 3 seconds, and the user won’t be able to change fan speed.

---

How do I disable fan speed lock?

Follow the same steps to activate Fan Speed Lock. However, in step 5 select OFF.

---

How do I activate the keypad lock?

Keypad Lock will prevent the user from changing the setpoint on the wall controller. Keypad Lock may be set independently on each wall controller connected. Press the PROG button to enter program Menu. Press the or buttons to navigate to Program Menu 07. Press the PROG button to enter Program Menu 07. Keypad lock is Off by default. Press the or buttons to turn the Keypad lock ON. Press the PROG button to accept the selection. Press the EXIT button once to go back to the main screen. When any button is pressed (EXCEPT PROG, DISP, AFTER HRS and or ), the symbol will appear for 3 seconds, and the user won’t be able to access any of those buttons.

---

How do I disable the Keypad Lock?

Follow the same steps above to activate the Keypad Lock. However, in step 5 select OFF.

---

How do I reset the filter timer?

Ensure the control is turned OFF before proceeding to resetting the Filter Timer. When the screen flashes FILTER, press the button to reset the timer after cleaning the filter. The flashing FILTER display will disappear.

---

How do I turn on/off and set the After Hours function?

The AFTER HOURS status is disabled (OFF) by default. For the AFTER HOURS run timer to operate, the TIME CLOCK operation has to be enabled. If the AFTER HOURS run timer overlaps with the scheduled TIME CLOCK event ON, the unit will continue running with the AFTER HOURS indicator displayed on the screen. Once the overlapped AFTER HOURS run timer expires, the control will turn OFF until the button is pressed again or the next scheduled ON event occurs. If the AFTER HOURS run timer expires earlier than the current TIME CLOCK event ON, the unit will continue operating to the current TIME CLOCK schedule. Press the AFTER HRS button. The after hours timer, AFTER HOURS, and OFF indicators will be displayed. Press the or buttons to select ON or OFF. Press the PROG button. AFTER HOURS will begin blinking. Press the or buttons to increase / decrease the AFTER HOURS timer in 0.5 hour (30 minute) increments. Press the PROG button to accept changes.

---

How do I cancel an active AFTER HOURS function?

Press the button. The unit will turn off, as well as the after hour function. If AFTER HOURS is canceled during a time clock schedule, the AFTER HOURS indicator will disappear, and the system will operate based on the time clock schedule. During the setting of AFTER HOURS, if no button is pressed for 5 seconds, the user will be returned to the home screen.

---

How do I activate the After Hours function?

Press the AFTER HRS button or the button. The AFTER Hours timer and ON will be displayed for 3 seconds. Once 3 seconds expires, the after hours function will now be active.

---

How can iOS users access the user manual using Near Field Communication (NFC)?

Go to the App Store and download NFC Reader for iPhone. Open the NFC App. Read through the NFC App Information and click on Let’s get started. Place the mobile device close to the NFC Tag on the control. Follow the instructions on the App. Once the tag has successfully scanned, a pop-up window will appear to redirect you to https://www.actronair.com.au/nfc. A list of Control Models will appear on the screen of your mobile device. Select the model number of your control to view the operation manual. The Model number of your control can be found underneath the Power On/Off button of the control.

---

How can Android users access the user manual using Near Field Communication (NFC)?

Go to Settings and look for NFC and payment. Press ON to activate NFC. Press Android Beam. Follow the on-screen instructions. Once successfully scanned, a pop-up window will appear to redirect you to the external website https://www.actronair.com.au/nfc. A list of Control Models will appear on the screen of your mobile device. Select the model number of your control to view the operation manual. The Model number of your control can be found underneath the Power On/Off button of the control.