Post questions, comments, reviews or page errors in the comment box below.
PDF Content Summary:
****** Page 1 ****** Setup Overview Refer to your User’s Manual for full System instructions and information. Reader Libre 2 FLASH GLUCOSE MONITORING SYSTEM Quick Start Guide for FreeStyle Libre 2 Reader USB Port Sensor Pack a Abbott Touchscreen Home Button Sensor 1 Applicator *CODE XXX. O Assemble and Apply Sensor to your body Start new Sensor with Reader Wait 60 mnutes for start-up Check your glucose whenever you want for up to 14 days Codes on labels must match Assemble and Apply Sensor to the back of your upper arm STEP 1 0 Select site on back of upper arm. Do not use other sites as these may result in inaccurate glucose readings. Note: Avoid scars, moles, stretch marks, lumps, and insulin injection sites. To prevent skin irritation, rotate sites between applications. STEP 4 Line up dark mark on Sensor Applicator with dark mark on Sensor Pack. On a hard surface, press down firmly on Sensor Applicator until it comes to a stop. STEP 7 Place Sensor Applicator over site and push down firmly to apply Sensor. Do not push down on CAUTION: Sensor Applicator until placed over prepared site to prevent unintended results or injury. STEP 2 Wash site using a plain soap, dry, and then clean with alcohol wipe. Allow site to air dry before proceeding. STEP 5 Lift Sensor Applicator out of Sensor Pack. STEP 8 Sensor Gently pull Sensor Applicator away from your body. Lid STEP 3 Cap Peel lid completely off Sensor Pack. Unscrew cap from Sensor Applicator. Sensor codes CAUTION: Sensor Pack I Enva must match on Sensor Pack ( Customer Service I Aten. and Sensor Applicator or glucose readings will be incorrect. STEP 6 CODE XXX •rxøxxxxx YYYY-W Sensor Applicator is ready to apply Sensor. Sensor Applicator CAUTION: now contains a needle. Do not touch inside Sensor Applicator or put it back into Sensor Pack. STEP 9 Make sure Sensor is secure. Discard used Sensor Applicator and Sensor Pack according to local regulations.
****** Page 2 ****** Start new Sensor with Reader STEP 1 Press Home Button to turn on Reader. Note: If using Reader for the first time, follow the prompts to set date and time. 3 Check your glucose STEP 1 Press Home Button to turn on Reader. STEP 2 Revi ew History STEP 3 Na Active Sensor art Important Do not take high doses af vitsmin C [more than SOO mg per eyi. This may fslsely raise your Sensor resdings. Supplements like Airborne: or Emer—en-CE high doses of vitamin C- RE3d Isbeling for all su pplem•ents to determine uitamin C content. New Sensor Starting Up Sensor can be Used in: 60 minutes Touch Start New Sensor. Hold Reader within 1.5 inches (4 cm) of Sensor to scan it. STEP 2 Hold Reader within 1.5 inches (4 cm) of Sensor to scan it. Review the important information on the screen. Sensor can be used to check your glucose after 60 minutes. STEP 3 Message Touch for more information Current Glucose Glucose from your latest scan Glucose Graph Graph ofyour current and stored glucose readings Glucose Trend Arrow 350 250 150 50 2pm 6pm dL 1 Opm What it means Glucose rising quickly Glucose rising Glucose changing slowly Glucose falling Glucose falling quickly Reader shows your glucose reading. This includes your Current Glucose, Glucose Trend Arrow, and Glucose Graph. Setting Alarms The Sensor automatically communicates with the Reader and can give you glucose alarms. Alarms are on by default. To change their settings or turn alarms off, follow these steps. Glucose alarms are an important safety feature. Please consult your health IMPORTANT: care professional before making changes. STEP 1 10:23pm @ Ends in 14 days Check Glucose Press Home Button to go to Home Screen. Touch Q}. STEP 2 Settings Alarms Sound & Vibration Time & Date 0K Alarm Settings Low Glucose 70 mg/dL High Glucose 240 mg/dL Signal Loss On Change Alarm Settings Notifies you when glucose is above the level you set. STEP 3 0K Change Alarm Settings Low Glucose Alarm High Glucose Alarm Signal Loss Alarm Notifies you when glucose is below the level you set. Notifies you when Sensor is not communicating with Reader and that you are not getting Low or High Glucose Alarms. Touch Alarms and then touch Change Alarm Settings. Select and set your alarms. Touch done to save. Using Alarms You must scan your Sensor to see your glucose reading. When any alarm is on, sound/vibration and signal status display on the Home Screen. Low Glucose Alarm Dismiss Alarm & Check Glucose High Glucose Alarm Dismiss Alarm & Check Glucose Signal Loss Alarm Scan Sensor now? No Yes 10:23pm @ Ends in lidays Check Glucose Symbol (e)) What it means Sound and Vibration ON Sound and Vibration OFF Sensor communicating with Reader Sensor not communicating with Reader Touch Dismiss Alarm & Check Glucose or press the Home Button to dismiss alarm and check your glucose. Touch No to dismiss alarm. Touch Yes or press the Home Button to dismiss alarm and scan the Sensor. Review History If you have followed the instructions described in the User’s Manual and are still having difficulty setting up your System or if you are not sure about a message or reading, contact your health care professional. Refer to User’s Manual for additional symbols. Manufacturer The shape of the circle sensor unit, FreeStyle, Libre, and related brand marks are owned by Abbott. 02019 Abbott ART40392-001 Rev.C06/20 Consult instructions for use Abbott Diabetes Care Inc. 1360 South Loop Road Alameda, CA 94502 USA Abbott
FREE ENGLISH PDF
USER GUIDE – USER MANUAL
OWNER GUIDE – OWNER MANUAL
REFERENCE GUIDE – REFERENCE MANUAL
INSTRUCTION GUIDE – INSTRUCTION MANUAL