ZANUSSI ZGH62414XS (01) PDF Document

Always light the burner before you put on the cookware. To ignite the burner on your ZANUSSI ZGH62414XS, follow these steps:

Step 1. Push the control knob down and turn it counterclockwise to the maximum gas supply position, indicated by the large flame symbol.

Step 2. Keep the control knob pushed for 10 seconds or less. This allow the thermocouple to warm up; otherwise, the gas supply will be interrupted.

Step 3. Adjust the flame after it is regular.

If after some tries the burner does not light, check if the crown and its cap are in the correct positions. If the burner does not light after 15 seconds, release the control knob, turn it to the off position, and wait at least 1 minute before trying to light the burner again.

Yes, in the absence of electricity, you can ignite the burner on the ZANUSSI ZGH62414XS without the electrical device. Approach the burner with a manual flame (such as a match or lighter), turn the control knob counterclockwise to the maximum gas supply position, and push it down. Keep the control knob pushed for 10 seconds or less to let the thermocouple warm up.

To put the flame out on the ZANUSSI ZGH62414XS, turn the control knob to the off position, which is indicated by a solid circle symbol. Always turn the flame down or switch it off before you remove pans from the burner.

You should use cookware with diameters applicable to the size of the burners on your ZANUSSI ZGH62414XS. The requirements are as follows:

For the ZANUSSI ZGH62414XS, do not use cast iron pans, clay or earthenware pots, or grill and toaster plates. Stainless steel can become tarnished if it is heated too much. Do not put the same pan on two burners, and do not use unstable or damaged pots to prevent spills and injuries.

The pan supports of the ZANUSSI ZGH62414XS are not resistant to washing in a dishwasher and must be washed by hand. Follow these steps:

Step 1. Remove the pan supports to easily clean the hob. Be careful when replacing them to prevent damage to the hob top.

Step 2. Wash them by hand and dry them. The enamel coating can occasionally have rough edges, so be careful during washing.

Step 3. If necessary, remove stubborn stains with a paste cleaner.

Step 4. After cleaning, ensure the pan supports are in the correct positions and that the arms are aligned with the center of the burner.

To maintain your ZANUSSI ZGH62414XS, clean the hob after each use. Follow these specific cleaning instructions:

Immediate Removal: Melted plastic, plastic foil, sugar, and food containing sugar must be removed immediately to avoid damaging the hob.

Normal Cleaning: Once the hob is sufficiently cool, remove limescale rings, water rings, fat stains, and shiny metallic discoloration. Clean the hob with a moist cloth and a non-abrasive detergent. After cleaning, wipe the hob dry with a soft cloth.

Burner Parts: To clean enamelled parts, caps, and crowns, wash them with warm soapy water and dry them carefully before putting them back on.

Stainless Steel: Wash stainless steel parts with water and dry with a soft cloth. For stubborn stains, soak them in a small amount of mild detergent for a few minutes before cleaning. Do not use cleaning products containing corrosive chemicals such as chlorides.

If there is no spark on your ZANUSSI ZGH62414XS, check the following possible causes and remedies:

Cause: The hob is not connected to an electrical supply or is connected incorrectly. Remedy: Check if the hob is correctly connected to the electrical supply.

Cause: The fuse is blown. Remedy: Make sure the fuse is the cause of the malfunction. If it continues to blow, contact a qualified electrician.

Cause: Burner cap and crown are placed incorrectly. Remedy: Place the burner cap and crown correctly.

Additionally, ensure the ceramic ignition candle (spark plug) and metal electrode are kept clean to prevent lighting difficulties, and check that burner crown holes are not obstructed.

The most likely cause for the flame extinguishing immediately on the ZANUSSI ZGH62414XS is that the thermocouple has not been heated up sufficiently. After lighting the flame, you must keep the control knob pushed down for equal to or less than 10 seconds to allow the thermocouple to warm up.

To adjust the minimum level of the burners on the ZANUSSI ZGH62414XS, use the following procedure:

Step 1. Light the burner.

Step 2. Turn the knob to the minimum position.

Step 3. Remove the knob and the gasket.

Step 4. Use a thin screwdriver to adjust the bypass screw position (A).

Step 5. If changing from natural gas G20 20 mbar to liquid gas, fully tighten the bypass screw in. If changing from liquid gas to natural gas G20 20 mbar, undo the bypass screw approximately 1/4 of a turn.

Step 6. Reassemble the gasket and the knob. Ensure the flame does not go out when you quickly turn the knob from the maximum to the minimum position.

To save energy with the ZANUSSI ZGH62414XS, follow these tips:

Before use, ensure the burners and pan supports are assembled correctly.

Use cookware with diameters that match the size of the burners.

Center the pot on the burner.

When heating water, use only the amount you need.

If possible, always put lids on the cookware.

When the liquid starts to boil, turn down the flame to barely simmer the liquid.

Use a pressure cooker if possible.

The terminal block on the ZANUSSI ZGH62414XS is marked as follows:

L: Live terminal

N: Neutral terminal

Earth symbol or E: Earth terminal

The wires in the supplied 3-core flexible power cable are colored as follows: Green and yellow for Earth, Blue for Neutral, and Brown for Live.

If the flame ring is uneven on your ZANUSSI ZGH62414XS, the burner crown may be blocked with food residues. Make sure that the injector is not blocked and the burner crown is clean.