ZANUSSI ZGH62414XA (01) PDF Document

To ensure the safety of children and vulnerable persons when using the ZANUSSI ZGH62414XA, follow these guidelines:

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.

Children between 3 and 8 years of age and persons with very extensive and complex disabilities shall be kept away unless continuously supervised.

Children of less than 3 years of age should be kept away unless continuously supervised.

Do not let children play with the appliance.

Keep all packaging away from children and dispose of it appropriately.

Keep children and pets away from the appliance when it operates or when it cools down. Accessible parts are hot.

If the appliance has a child safety device, it should be activated.

Children shall not carry out cleaning and user maintenance of the appliance without supervision.

Observe the following safety warnings during the use of your ZANUSSI ZGH62414XA:

WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements.

Do not operate the appliance by means of an external timer or separate remote-control system.

WARNING: Unattended cooking on a hob with fat or oil can be dangerous and may result in fire.

NEVER try to extinguish a fire with water, but switch off the appliance and then cover flame e.g. with a lid or a fire blanket.

CAUTION: The cooking process has to be supervised. A short term cooking process has to be supervised continuously.

WARNING: Danger of fire: Do not store items on the cooking surfaces.

Metallic objects such as knives, forks, spoons and lids should not be placed on the hob surface since they can get hot.

Do not use a steam cleaner to clean the appliance.

The control knobs on the ZANUSSI ZGH62414XA use specific symbols to indicate the gas supply status:

A solid circle symbol indicates no gas supply or the off position.

A large flame symbol indicates the ignition position or the maximum gas supply.

A small flame symbol indicates the minimum gas supply.

Always light the burner before you put on the cookware. Follow these steps to ignite the ZANUSSI ZGH62414XA burners:

Step 1. Push the control knob down and turn it counterclockwise to the maximum gas supply position (indicated by the large flame symbol).

Step 2. Keep the control knob pushed for equal or less than 10 seconds. This lets the thermocouple warm up. If not, the gas supply is interrupted.

Step 3. Adjust the flame after it is regular.

If the burner does not light after several attempts, check if the burner crown and its cap are in the correct positions. If the burner accidentally goes out, turn the control knob to the off position and try to light the burner again after a minimum of 1 minute.

In the absence of electricity, you can ignite the ZANUSSI ZGH62414XA burner without the electrical device. Approach the burner with a flame, turn the control knob counterclockwise to the maximum gas supply position, and push it down. Keep the control knob pushed for equal or less than 10 seconds to let the thermocouple warm up.

To put the flame out on the ZANUSSI ZGH62414XA, turn the control knob to the off position (indicated by the solid circle). Always turn the flame down or switch it off before you remove the pans from the burner.

When using cookware on the ZANUSSI ZGH62414XA, follow these safety instructions:

Do not use cast iron pans, clay or earthenware pots, grill or toaster plates. Stainless steel can become tarnished if it is heated too much.

Do not put the same pan on two burners.

Do not put unstable or damaged pots on the burner to prevent spills and injuries.

Make sure that the bottoms of pots do not stand too close to the control knob, otherwise the flame may heat the control knob up.

Make sure that pot handles are not above the front edge of the cooktop.

Ensure that the pots are placed centrally on the burner in order to get the maximum stability and lower gas consumption.

Use cookware with diameters applicable to the size of the burners as follows:

Follow these general cleaning guidelines for the ZANUSSI ZGH62414XA:

Clean the hob after each use and always use cookware with a clean base.

Use a special cleaner suitable for the surface of the hob. Scratches or dark stains on the surface have no effect on how the hob operates.

For stainless steel parts, wash with water and then dry them with a soft cloth.

To remove burnt food or fat, let them soak in a small amount of mild detergent for a few minutes before cleaning. Use products designed specifically for stainless steel.

Do not use cleaning products containing corrosive chemicals such as chlorides, and do not use disinfectants, stain or rust removers, or immersion cleaners.

Clean the enamel coating of pan supports by hand and dry them. If necessary, remove stubborn stains with a paste cleaner. Make sure the pan supports are correctly positioned and aligned with the center of the burner after cleaning.

Do not clean the burners or pan supports in the dishwasher.

Remove melted plastic, plastic foil, sugar, and food with sugar immediately from the ZANUSSI ZGH62414XA surface, as these can cause damage to the hob. Take care to avoid burns during this process.

Wait until the hob is sufficiently cool to remove limescale rings, water rings, fat stains, and shiny metallic discoloration. Clean these with a moist cloth and a non-abrasive detergent before wiping the hob dry with a soft cloth.

If you encounter issues with your ZANUSSI ZGH62414XA, refer to the following troubleshooting table:

To adjust the minimum level of the ZANUSSI ZGH62414XA burners:

Step 1. Light the burner.

Step 2. Turn the knob to the minimum position.

Step 3. Remove the knob and the gasket.

Step 4. With a thin screwdriver, adjust the bypass screw position (A).

Step 5. If you change from natural gas G20 20 mbar to liquid gas, fully tighten the bypass screw in. If you change from liquid gas to natural gas G20 20 mbar, undo the bypass screw approximately 1/4 of a turn.

Step 6. Reassemble the gasket and the knob. Make sure the flame does not go out when you quickly turn the knob from the maximum to the minimum position.

The technical data for the ZANUSSI ZGH62414XA is as follows:

To save energy while cooking with your ZANUSSI ZGH62414XA, follow these tips:

Before use, make sure that the burners and pan supports are assembled correctly.

Use cookware with diameters applicable to the size of the burners.

Center the pot on the burner.

When you heat up water, use only the amount you need.

If it is possible, always put the lids on the cookware.

When the liquid starts to boil, turn down the flame to barely simmer the liquid.

If it is possible, use a pressure cooker.