XZENT X-F275 (01) PDF MANUAL

XZENT X-F275 (01) PDF SUMMARY:

What should you do before replacing a defective fuse? Before you replace a defective fuse, try to find the cause for the short circuit. Pay attention to the cables of the power supply!

If the short circuit does not result from a failure of the power supply or wiring, what can you do? You can replace the defective fuse with a new one (of identical value).

What should you do if the short circuit persists after replacing the fuse? Contact an authorized XZENT dealer.

When connecting to any other device, what should you do? Read the user‘s guide for compatibility and notes on electrical connections.

What should you not try to do when connecting to other devices? Do not try to connect incompatible products.

Why should you be careful not to drain the car battery while using the unit when the car engine is turned off? The unit consumes a considerable amount of energy and the battery will be charged only while the engine is running. If the battery discharges to a point where it is not possible to start the engine anymore.

Why is it not allowed to drive with monitors showing movies in the viewing range of the driver? The driver might get distracted from traffic.

Why should you pay attention to the playback volume inside your vehicle? You are required to notice exterior warning sounds like police sirens etc.

What could happen if the unit is exposed to hard impacts? A mechanical or electrical malfunction of the unit could be the result.

What should you do if any problems or questions occur during the installation? Consult your XZENT dealer/importer.

What is the function of the VOL/POWER button?

• Press and hold for standby mode (Screen OFF, Audio OFF).
• If powered on, press to mute.
• If powered off, press to power on.
• Rotate clockwise to increase audio volume.
• Rotate anti-clockwise to decrease volume.

What is the function of the Home button?

• Press to return to the home screen.
• Press in the home screen to go to the last source (if available).
• Press and hold to open EQ.

What is the function of the NAV button? Press to open navigation mode.

What is the function of the CAM button? Press to show the default camera; press again to close the camera view.

What is the function of the VOICE button? Press to start voice recognition (in use with CarPlay).

What is the function of the DAB button? Press to open DAB source. In DAB source press again to switch to FM.

What is the function of the FAV button?

• Press to execute assigned FAV short press function from device settings.
• Press and hold to execute assigned FAV long press function from device settings.

What is the function of the RESET button? Press to perform a power reset.

What is the function of the MAP slot? MicroSD slot for navigation software (optional, not included in this set).

What is the function of the MIC? Internal microphone for handsfree functions.

What is the function of the IR? IR eye for remote control.

What are the USB1 and USB2 ports used for?

USB Port	Function
USB1	Can be used for SW Updates
USB2	NOT for software updates

Where can you find information about software updates, customer care, FAQs, and other helpful information? Software updates and improvements are provided via USB updates which can be downloaded from our website http://www.xzent.com.

Which specific USB port has special functions? This device has specific USB ports with special functions (USB-1 / top port at device backside) and (USB-2 / bottom port at device backside).

How are the extension cables distinguishable? The extension cables are distinguishable through text-label to ensure proper identification.

Where MUST software updates provided via XZENT be installed? Software updates provided via XZENT MUST be installed on “USB-1” (USE FOR SW UPDATE).

What should you do if the installation has been done by a 3rd party without proper marking/identification of the extension wire and you experience an update failure? Try the other port in case of update-failure.

What can be used as an alternative to the preconfigured IR-Stalk-Interface (not included in the set)? An existing steering wheel control can be directly connected if a mini-ISO connector at the car side is present to the XZENT Analogue Key interface.

What do both the IR-mode and analogue-Mode mimic? Both the IR-mode and the analogue-Mode are preconfigured to functionally mimic the standard SWC functions.

How is the functionality set in IR-mode? By code and cannot be changed.

Can the functionality of analogue-mode be changed? Yes, the analogue mode allows you to change or reassign the functionality to your liking.

What is the function of the Skip next button in MODE 2, FIAT DUCATO SERIES 8? This button follows the Graphical User Interface (GUI) function of the active audio source.

What is the function of the CAM/voice button in MODE 2, FIAT DUCATO SERIES 8?

• Press to activate CAM source. Press again to close CAM source.
• Press & hold to activate CarPlay voice control.

What is the function of the Skip last button in MODE 2, FIAT DUCATO SERIES 8? This button follows the Graphical User Interface (GUI) function of the active audio source.

What is the function of the Vol+ button in MODE 2, FIAT DUCATO SERIES 8? Press to increase the active audio volume level. For example, press while Navigation Voice is speaking to increase the volume level of Navigation voice; the ducked or muted media audio stays unchanged.

What is the function of the Mute/Pickup/hang-up button in MODE 2, FIAT DUCATO SERIES 8?

• While no active call, press to MUTE or unmute all audio.
• During incoming call (ringing), press to pick up call.
• While active call, press to end call.

What is the function of the Vol- button in MODE 2, FIAT DUCATO SERIES 8? Press to decrease the active audio volume level. For example, press while Navigation Voice is speaking to decrease the volume level of Navigation voice; the ducked or muted media audio stays unchanged.

How can you customize the buttons of your SWC to your preference in MODE 2, FIAT DUCATO SERIES 8? You can customize the buttons of your SWC to your preference by placing standard or alternative buttons to your SWC.

What are the alternative button functions in MODE 2, FIAT DUCATO SERIES 8?

• A1. Alternative function SRC/voice: Press to select a different Source via Main Menu highlighting.
• A2. Alternative function NAV/voice: Press to start NAV function. Press & hold to activate CarPlay voice control.

What does button B do in MODE 2, FIAT DUCATO SERIES 8? This button will reset any custom configuration on the SWC back to factory settings.

What is the function of the Return button in the MAIN MENU? Press to return to the home screen.

What information does the List area in the MAIN MENU show? The shown list area depends on the currently selected category.

How can you see other settings in the List area in the MAIN MENU? You can scroll/swipe the list up and down or select a different category from the lower area.

What settings are contained in the General category of the MAIN MENU? Contains general settings like language, date&time, FAV key assignment.

What settings are contained in the Audio category of the MAIN MENU? Contains settings for audio and sound adjustments.

What settings are contained in the TFT category of the MAIN MENU? Here you can adjust settings regarding the screen, for example, brightness mode or brightness values.

What settings are contained in the Camera category of the MAIN MENU? Enables you to adjust settings on the connected rearview camera.

What settings are contained in the Miscellaneous category of the MAIN MENU? Here you can find information on the software device version and load factory.

What is the function of the Return button in the DAB RADIO SOURCE? Press to return to the home screen.

What settings are available in the Settings category of the DAB RADIO SOURCE?

• 2(a) DAB-DAB Service Following: Press to switch function ON/OFF.
• 2(b) Antenna supply: Press switch to activate/deactivate 12V power supply for your DAB antenna.
• 2© DAB Firmware: Shows current DAB firmware version.

What information does the Info category of the DAB RADIO SOURCE provide? This view allows you to see current played station logos, slideshow pictures and text which is aired from the station.

How do you change the station of the current selected ensemble in the Info category of the DAB RADIO SOURCE? Press the arrow keys to change the station of the current selected ensemble.

How do you change to the next possible ensemble in the Info category of the DAB RADIO SOURCE? Press and hold the arrow keys to change to the next possible ensemble – the first station of the new ensemble will be auto-played.

What information does the List category of the DAB RADIO SOURCE provide? The list view allows you to see all received ensembles and will be periodically refreshed.

How do you select an ensemble in the List category of the DAB RADIO SOURCE? You can select an ensemble by tapping on it and it will show the contained stations which you also can directly tap to play.

What does the Preset category of the DAB RADIO SOURCE show? This view shows the preset buttons that work like a quick select or favorite button.

How do you save the current station to a preset button in the Preset category of the DAB RADIO SOURCE? To save the current station to a preset button, press and hold it until the button is updated with the station information.

What is the function of the FM button in the DAB RADIO SOURCE? Press the button to change directly to FM radio source.

What is the function of the Return button in the FM RADIO SOURCE? Press to return to the home screen.

What settings are available in the Settings category of the FM RADIO SOURCE?

• 2(a) Auto Save: Press Start to initiate auto search&store for the presets.
• 2(b) Mode: Press the key arrows to change DX/LOC mode shown next to the frequency.
• 2© AF: Press switch to ON/OFF AF-function (Alternative Frequencies).
• 2(d) TA: Press switch to ON/OFF TA function (FM Traffic Announcements).

What information does the Info category of the FM RADIO SOURCE provide? This view will show you the station name and the received radio text. Between the up and down seek buttons (arrow keys) the frequency is additionally displayed.

How do you initiate up/down seek to the next receivable station in the Info category of the FM RADIO SOURCE? Press the arrow keys to initiate up/down seek to the next receivable station.

What information does the Scale category of the FM RADIO SOURCE provide?

• (A) FM Frequency scale band with a marker of the current tuned frequency.
• (B) Current set frequency.
• © Current FM Mode. Can be changed in FM Settings.

How do you single-step 0.1 MHz up/down in the Scale category of the FM RADIO SOURCE? Press the arrow keys to single step 0.1 MHz up/down.

How do you initiate up/down seek to the next receivable station in the Scale category of the FM RADIO SOURCE? Press the arrow keys to initiate up/down seek to the next receivable station.

What does the Preset category of the FM RADIO SOURCE show? This view shows the preset buttons that work like a quick select or favorite button.

How do you save the current station to a preset button in the Preset category of the FM RADIO SOURCE? To save the current station to a preset button, press and hold it until the button is updated with the station information.

What is the function of the DAB button in the FM RADIO SOURCE? Press the button to directly switch to DAB radio source.

How can you browse your media files in the list view mode? At the list view mode (not available in Bluetooth music) you can browse your media files similar like a folder-file list.

How do you open folders in the list view mode? To open folders just simply tap on them to show their content which you also can directly tap to start playback.

What indicates that a file is playing in the list view mode? It will be shown with a play icon and also at the bottom line.

How do you go back one level in the list view mode? Use the back (A) button.

How do you change to the video media type (only USB mode) in the list view mode? By pressing (B) the filter icon.

When is video playback possible? Only if the handbrake is engaged.

In what mode will video playback be? Full screen mode.

How do you leave full screen mode during video playback? Press simply the touch screen area of your device.

How can you access the USB, iPod, and BT music sources? The sources USB and iPod can be accessed among other ways thru their home screen icon and BT music with a connected phone via the Bluetooth source to play audio (BT, USB, iPod) or video (USB only).

What is the function of the Return button in the USB/iPod/BT MUSIC (A/V) SOURCE? Press to return to the home screen.

What is the function of the EQ button in the USB/iPod/BT MUSIC (A/V) SOURCE? Press to open equalizer settings.

What is the function of the Search button in the USB/iPod/BT MUSIC (A/V) SOURCE? Press to open search (not available in Bluetooth music).

What is the function of the List button in the USB/iPod/BT MUSIC (A/V) SOURCE? Press to open the list view (not available in Bluetooth music).

How do you pair your compatible phone on initial use? On initial use the category (2) is active and you can pair your compatible phone via scan/search.

What should you ensure during the pairing process?

• Ensure your phone is visible until it appears in the search result list.
• Confirm the pass key.
• Ensure that permission such as to contacts are granted/accepted.

How are active or auto-connected phones shown in the status area (A)? With an active Bluetooth icon, battery and signal strength icon (if supported).

What is the function of the Return button in the BLUETOOTH PAIRING, CONNECTING, CALLING, MUSIC section? Press to return to the home screen.

What actions can be performed in the Devices category of the BLUETOOTH PAIRING, CONNECTING, CALLING, MUSIC section? Here you can manage your paired phones (manual connect/disconnect, delete) or add new phones via search.

How do you manually disconnect a phone in the Devices category of the BLUETOOTH PAIRING, CONNECTING, CALLING, MUSIC section? Tap the connect/disconnect button to disconnect manually and connect a different other phone.

How do you delete a paired phone in the Devices category of the BLUETOOTH PAIRING, CONNECTING, CALLING, MUSIC section? Tap the waste bin icon button to delete a paired phone.

How many phones can be connected at the same time? It is only possible to connect a single phone at the same time.

What is the function of the Keypad button in the BLUETOOTH PAIRING, CONNECTING, CALLING, MUSIC section? Press to open the dial keypad with the active phone.

What actions can be performed in the Contacts category of the BLUETOOTH PAIRING, CONNECTING, CALLING, MUSIC section?

• Press to open the contact list of the active phone.
• You can manually re-sync in case if not all contacts are shown or new contacts have been added to the phone.
• You can slide the list or use the search function to look up a contact.
• A contact can be operated like a folder and be tapped to open its containing numbers.
• Tap on the line number to initiate a call attempt.
• Use the orange back button on the top left position of the list view to browse one level up.

What does the Call log category of the BLUETOOTH PAIRING, CONNECTING, CALLING, MUSIC section provide? Here you have a separate list view for outgoing, received/incoming or missed calls.

How do you initiate a call attempt from the Call log? You can tap a line to initiate a call attempt.

What is the function of the Music button in the BLUETOOTH PAIRING, CONNECTING, CALLING, MUSIC section? Press to initiate the Bluetooth music playback via A2DP.

What might be required on some smartphones before using the Music button? Some smartphones need to start the music app on the smartphone first.

What settings are available in the Setup category of the BLUETOOTH PAIRING, CONNECTING, CALLING, MUSIC section?

• 6(a) Auto Connect: Press switch to ON/OFF Auto Connect.
• 6(b) Auto Answer: Press switch to ON/OFF Auto Answer.
• 6© Microphone Gain: Press arrow keys to change values.
• 6(d) Contact Order: Press arrow keys to change value.

What happens on an incoming/outgoing or active call? The device will automatically switch to a full-screen mode and shows you the contact name or number (if available) or unknown in case of a suppressed caller ID.

What actions can be performed during a call depending on the call status (initiate, ringing, dialling, active)?

• You can hang-up, reject, accept/pick-up a call (1).
• On active call you can switch to private mode (2) or to car loudspeakers.
• Mute the XZENT microphone (3).
• Open the keypad for call options (4).
• (5) to return to navigation mode.

What is Android Link? With Android Link you can connect your compatible Android Phone to the XZENT device and enjoy compatible smartphone apps in your car.

What should you do to use Android Link? Make sure that you enabled the Android Link function in the system settings of your XZENT device.

What are the steps to use Android Link?

1. To use this functionality you first need to download the AutoLink Host App from your App-Store.
2. Launch the AutoLink Host App on your phone.
3. Unlock your Phone and connect it via USB-1 to your XZENT – make sure your XZENT Setting is set to Android Link.
4. Press the Android Link home screen icon on your XZENT.
5. On the initial connection allow/accept requested access and accept and Bluetooth pairing request.

What is the A/V-IN, HDMI SOURCE? The A/V-IN and HDMI source can be entered among other ways via the home screen icon. The source will provide you the A/V-IN or HDMI signal input to your XZENT device.

Is there a specific touch operation for A/V-IN and HDMI? There is no specific touch operation here besides the back to home screen button.

What is the function of the Return button in the A/V-IN, HDMI SOURCE? Press to return to the home screen.

How can the Navigation source be accessed? The Navigation source can be entered among other ways via the home screen icon or the NAV front key sensor.

Where should you insert the microSD card for navigation? Insert the microSD card (not included in the set) to the NAV slot of the device.

Where can you find a quick start guide for the Navigation source UI operation? A quick start guide is provided.

What does the Sat/DR Symbol indicate? This symbol will show in DAB, FM, and other media sources and inform you on the positioning precision and shows different icons and colors.

What are the different icons and colors of the Sat/DR Symbol?

• Gray SAT-icon if no GPS signal is available.
• White SAT-icon if no position is possible.
• Green SAT-Icon if the position is OK.
• Green Gyro-Icon if the DR system is active.

How is the navigation software and maps on your microSD card (not included in the set) maintained and updated? Via http://www.naviextras.com.

Where can you find additional information, help, and instructions on how to install the toolbox and perform the desired action for navigation software? You can find additional information, help, and instructions on how to install the toolbox and perform the desired action.

How many active route guidances can you have? You can only have one active route guidance.

What happens if native route guidance is started in the navigation source? CarPlay route guidance is automatically terminated in order to avoid the voice prompts from 2 systems for route guidance.

Can CarPlay still be used in the background if native route guidance is started? Yes, CarPlay can continue to be used in the background, e.g. for music playback.

What is Apple CarPlay? With Apple CarPlay, you are able to access compatible apps and online services of your iPhone in your car and operate them intuitively with the display of your XZENT device or the voice assistant from Apple.

What preparations are needed for Apple CarPlay?

• Connect the compatible iPhone with the USB-1 port of the XZENT device.
• In case Bluetooth is not paired automatically, connect manually.
• Unlock your iPhone.

What are the steps for initial operation of Apple CarPlay?

1. For the initial operation, the vehicle must not be in motion and the hand brake must be engaged.
2. Tap to the CarPlay icon in the main menu of the XZENT device to choose the CarPlay source. After the initial operation has been completed successfully, the CarPlay user interface appears on the screen of the XZENT device.

What is the function of button 1 in the APPLE CARPLAY section? Tap to display the home screen of CarPlay.

What is the function of button 2 in the APPLE CARPLAY section? Tap to open XZENT main menu.

What is the function of button 3 in the APPLE CARPLAY section? Tap any of the APP icons to start the application.

What happens if a route guidance is started with CarPlay? The native navigation source is terminated in order to avoid the spoken messages of 2 systems for route guidance.

What needs to be done to start the navigation source the next time it is used after a route guidance is started with CarPlay? The navigation source is no longer started automatically and must be started manually the next time it is used.

What products are covered by XZENT’s limited Warranty? The limited Warranty (the “Warranty”) applies to XZENT products purchased from an authorized dealer by end customers in the European Economic Area or Switzerland.

What is the validity period of XZENT’s Warranty? XZENT warrants, for a period of 2 years, that the product is free from defects in material and/or workmanship at the time of the original purchase. This 2-year period commences on the date of the original purchase as per the original invoice or until receipt. If you have purchased the product as a consumer, and the defect is identified within the first six months after the original purchase, we will assume that the defect already existed at the time of purchase.

Who can claim under the Warranty? XZENT grants the limited Warranty to natural persons only, who purchased the relevant product primarily for personal use.

What is covered by the Warranty? XZENT warrants that the product is free from defects in material and/or workmanship at the time of the original purchase. It only covers the hardware components of the device, and in no event the software used with the device, regardless if this was provided by XZENT or the third-party vendor.

What is NOT covered by the Warranty?

• normal wear and tear (such as to surfaces and protective coverings)
• superficial damage, such as scratches, dents, and damaged plastic, worn or mechanically defective connections
• misuse, including any treatment resulting in physical or superficial damage, such as a cosmetic defect, to the product
• damage caused by connecting or using the product for a purpose other than those specified, or a failure to observe the operating and/or installation instructions for the particular model
• installation or use of the product contrary to the applicable technical standards, or the safety regulations in the country in which the product is installed or used
• damage caused through an unauthorized attempted repair, or an attempted repair by someone other than a XZENT authorized service partner
• damage caused by modifications to the product not expressly authorized by the manufacturer
• damage caused by malicious code (“Software Viruses”) or by using software not supplied with the product or which was incorrectly installed
• use of third-party vendor software programs for editing, modifying, adapting, or extending XZENT’s authorized software components as are run on the product
• use of third-party vendor firmware/operating system software
• damage caused by liquids or chemicals of whatever type, and/or excessive temperatures, moisture, or damp
• accidents, drops or other such effects of extreme accelerating forces
• damage caused by lightning strikes, electrostatic charge, incorrect operating voltage, water, fire, force majeure, inadequate ventilation for other reasons for which XZENT is not responsible
• damage caused by using the device outside of the defined specifications
• damage caused by using the product with other systems or devices, which are not designed to be used with this product
• adjustments or modifications without XZENT‘s prior written approval, including product upgrades extending beyond the specifications or characteristics described in the operating manual
• modifications of the product for the purpose of adapting it to national or local technical norms or safety standards of countries for which the product was not expressly designed or manufactured
• using service or spare parts not produced or distributed by XZENT
• using the product in connection with accessories not approved for use with this product

Does XZENT warrant the quality, performance, reliability, or suitability of the product for a particular purpose? XZENT does not warrant (expressly, implicitly, statutorily, or otherwise) the quality, performance, reliability or suitability of the product for a particular purpose except as described, nor the software/firmware installed on the device ex works.

Will warranty service be provided if the model number / serial number / UUID / product number on the product is changed, erased, made illegible or removed? No warranty service will be provided if the model number / serial number / UUID / product number on the product is changed, erased, made illegible or removed.

What if the receipt or invoice is incomplete and/or illegible when presented? The same applies if the receipt or invoice is incomplete and/or illegible when presented.

Is XZENT liable for other defects or damage? XZENT will repair or replace products, only if they are covered by the terms of this Warranty. XZENT is not liable for any material or intangible loss or damage such as the price paid for the product, loss of profits, revenue, data, or relating to the enjoyment of the product or components associated with it, arising directly or indirectly under this Warranty or otherwise in relation to products or services.

Is XZENT liable for shipment-related risks? XZENT does not accept any liability for shipment-related risks – such as the loss or destruction of the product – in connection with the fulfillment of the Warranty.

To what extent will XZENT limit its Warranty and liability if these disclaimers are prohibited or limited under the applicable law? If these disclaimers are prohibited or limited under the applicable law, XZENT will limit its Warranty and liability to the extent permissible under the applicable regulations.

What is XZENT’s liability limited to for the duration of this Warranty? For the duration of this Warranty, all liability that cannot be excluded completely will be limited to the extent permissible under the applicable law. Liability under this Warranty is limited to the price paid for the product. If the applicable law only permits higher limits on any liability, this higher limitation will apply.

How do you exercise your Warranty rights? If you want to exercise your entitlements under this Warranty, please contact the authorized dealer where the product was purchased, and present it with the original copy of the till receipt or invoice.

Should you return any products to XZENT directly? Do not return any products to XZENT directly, otherwise our Warranty obligations cannot be fulfilled.

Where can you find the name of the relevant dealer or reseller? On your proof of purchase.

What should accompany defective devices sent by the authorized dealer to the service center? Defective devices sent by the authorized dealer to the service center, must also be accompanied by any accessories with a logical connection to the observed fault.

What is an example of an accessory that should accompany a defective device? This means, for example, the navigation package on an SD or microSD card supplied or purchased with the device, if problems or functional errors were observed in connection with the navigation function.

How will XZENT fulfill its Warranty? XZENT or its service partner will choose to either repair or replace the product or its defective parts covered by the Warranty, and assume the costs of material and labor in doing so.

Who must carry out repairs under the Warranty? Repairs under the Warranty must be carried out by XZENT or its authorized service partner.

What might repaired or replaced products contain? Products that are repaired or replaced may contain new and/or refurbished components and devices.

Who will become the property of components that are swapped out? Components that are swapped out will become the property of XZENT.

Will you incur any costs in connection with the Warranty service? XZENT assumes the costs of material and labor in connection with its Warranty service. The Warranty holder is responsible for the costs of shipment and bears the risks connected with the shipment.

What happens if the product is found to be operating faultlessly, or there is no warranty entitlement? If the product is found to be operating faultlessly, or there is no warranty entitlement because the warrant period has expired or for any other reason, XZENT or its authorized service partner will be entitled to charge a flat-rate investigation fee of €30.00.

Does the Warranty affect your statutory or contractual rights? This Warranty is made voluntarily by XZENT, and it will, in any case, extend your statutory rights. As a consumer, you remain fully entitled to your statutory rights, such as the statutory guarantee. This Warranty also has no effect whatsoever on your contractual rights against the reseller. You may continue to exercise these rights in full.