XPOWER XD-75LH (01) PDF MANUAL

XPOWER XD-75LH (01) PDF SUMMARY:

What safety instructions should I follow before using the dehumidifier?

• Read and save the provided instructions before using the product. Failure to follow these instructions may result in injury, fire, or electrical shock, damage the appliance, impair its operation, and void the warranty.
• Remove all packaging material and check for any shipping damage or missing items before operating.
• Ensure the household power supply matches the appliance’s specification.
• Do not operate the appliance with a damaged cord or plug. Discard or return it to an authorized service facility for examination and/or repair.
• Do not use an extension cord with this appliance. Use only with GFCI protected receptacles. Contact a qualified electrician for verification or installation of a GFCI receptacle if necessary.
• Do not run the cord under carpeting or cover it with rugs or similar coverings. Arrange the cord away from traffic areas to avoid tripping.
• To reduce the risk of fire or electric shock, do not use this appliance with any solid-state speed control device.
• Do not touch the appliance or plug with wet hands or while standing in water.
• Do not operate the appliance near any pooled water.
• Do not use the product in areas where gasoline, paint, or other flammable goods and objects are used or stored.
• Do not insert or allow objects to enter any ventilation or exhaust opening, as this may damage the appliance and void the warranty.
• Do not cover the air inlet or outlet on the appliance.
• Do not direct the airflow at human faces or bodies.
• Do not allow children to play with this appliance.
• Disconnect from the power supply before servicing to reduce the risk of injury.
• Remove the power cord from the electrical receptacle by grasping and pulling on the plug-end only; do not pull the cord directly.
• Do not attempt to repair or adjust any electrical or mechanical functions of this appliance, as this may cause danger and void the warranty.
• If the appliance is damaged or malfunctions, do not continue to use it. Unplug the product and refer to the troubleshooting guide or contact XPOWER.
• Store in a dry area, away from exposure to sunlight, extreme temperature and humidity, or other extreme environments, when not in use.
• Do not stack this appliance to more than three units.
• Always grip the trolley handle and keep the unit upright when transporting it. Do not tilt the product on its side or upside down.
• If the dehumidifier was transported tilted on its side or upside down, position it upright and wait at least 4 hours before using it again.

---

How do I select the right location for the dehumidifier?

• Positioning: Place the unit upright for at least 1 hour before use to allow the refrigerant to stabilize. If the unit was tilted, set it upright for at least 4 hours before use. The dehumidifier must be upright on a level surface during use.
• Enclosed Area: Operate the dehumidifier in an enclosed area, keeping all doors, windows, and outside entrances closed. Turn off the air conditioning for optimal efficiency.
• Air Circulation: Ensure constant and efficient air circulation, for example, by setting up circulation with XPOWER Air Mover combinations.
• Environment Temperature/Humidity: The dehumidifier is designed to work in temperatures from 33 °F to 105 °F (0.6 °C to 40.6 °C) and a relative humidity of 20% or higher. It may not function normally if these levels are exceeded.
• Power Cord and Drain Hose: Select a location where the power cord (25 feet/7.5 meters) can reach the power source and the drain hose (40 feet/12 meters) can reach the desired drainage area.
• Inlet and Outlet Orientation: Ensure the airflow from the inlet and outlet won’t affect nearby objects.
• Important: Keep new moisture-laden air away from the working area and allow sufficient enclosed air circulation. For larger areas, multiple dehumidifiers may be required.

---

How do I install the power cord?

Connect the plug connector on the power cord to the power outlet of the machine.

---

How do I install the drain hose?

Attach the drain hose inlet to the drain outlet of the machine. Ensure a separate container is available to collect water from the other end of the drain hose.

---

How do I install the trolley handle?

1. Slide the trolley handle under the hand carry handle and in front of the secondary intake.
2. Align the screw holes on the trolley handle to the threaded holes on the housing.
3. Install the internal hex screws with the hex key.

---

How do I set up the intake ducting (optional)?

1. Install the intake adapter.
2. Screw on the four screws.
3. Attach the ducting hose to the intake adapter.

---

How do I set up the exhaust ducting (lay flat)?

1. Unscrew the two screws.
2. Take out the ducting frame.
3. Let the ducting hose go through the ducting frame.
4. Turn the ducting hose around the frame to its back.
5. Reinstall the ducting frame and screw on the two screws.

---

How do I use the power control on the control panel?

Press the Power Control button to switch the dehumidifier ON or OFF.

---

How do I use the Fahrenheit/Celsius Scale Switch on the control panel?

Press to switch the display of the temperature in Fahrenheit or Celsius scale.

---

How do I use the Evaporator Coil/Environment Temperature Switch on the control panel?

Press to switch the display of the temperature of the evaporator coil or environment.

---

How do I use the Manual Drainage button on the control panel?

Press to drain manually. Manual drain will last for 3 minutes (180 seconds).

---

How do I use the Humidity Control on the control panel?

Tap “+”/“-” to increase/decrease the desired humidity level by 1% increments. Touch and hold to increase/decrease the setting humidity level by 5% per second. The adjustable range is 30% to 90%.

---

What does the Temperature Display on the control panel show?

This will show the temperature of the evaporator or environment. When in Celsius scale, °C will be illuminated. When in Fahrenheit scale, °C will turn off. If the temperature to show is higher than 99 ° F, the scale will be set to Celsius automatically.

---

What does the Fan Speed indicator on the control panel show?

This will show if the machine is running on low or high fan speed. When the environment humidity reaches lower than 30%, the machine will run on low fan speed.

---

What does the Total Running Time indicator on the control panel show?

This will show the total running time from the first usage to the current moment. Running time starts to count during the time when the machine turns on. The value can’t be reset.

---

What does the Defrosting Light indicator mean?

This light indicates the evaporator coil or environment temperature is too low. Frost may start to appear on the evaporator coil. The machine is now defrosting.

---

What does the Constant Dehumidification indicator mean?

At the humidity level setting of 30%, if humidity control button “-” is pressed, this will blink on the humidity display. The machine will enter into constant dehumidification mode and won’t stop dehumidification as environment humidity changes.

---

What does the OFF Light indicator mean?

This light indicates the machine is connected to a power source and it is now turned off.

---

What does the Dehumidification Light indicator mean?

When this light blinks, it indicates the machine is now preparing for dehumidification. When this light stays bright, it indicates the machine is now dehumidifying.

---

What does the Water Tank Full Indicator Light mean?

This light indicates the water tank is full of water or the water tank is not positioned horizontally. The machine will automatically drain the water out for 3 minutes (180 seconds).

---

What do the Error Codes indicate?

These are error codes. Refer to the Troubleshooting Guide for more information.

---

How do I turn on the dehumidifier and start a job?

1. Press the Power Control button to switch on the machine. The dehumidification light may flash.
2. Wait for 3 minutes (180 seconds) until the machine completes the startup.
3. Write down the starting time right after the machine starts to calculate the usage time.

---

How do I set the desired humidity level?

1. Tap the humidity control button to adjust the setting humidity level. The adjustment range is from 30% to 90%. The machine will try to match the setting humidity level and maintain it.
2. To have the machine work constantly, adjust the humidity level down to 30%, and then press “-”. Tap “+” to exit constant dehumidification mode.
3. If the dehumidifier is shut off or loses power, when turned on again, the dehumidifier will work on the last known configuration.

---

How does dehumidification work?

• When the machine is dehumidifying, the dehumidification light goes on.
• If the dehumidification light is flashing, it means that dehumidification is temporarily paused or the environment humidity has reached the setting level. Wait until the machine completes the startup or until the humidity level rises again.

---

How does defrosting work?

• When the evaporator coil or the environment temperature is too low, frost may appear on the evaporator, which will cause a lower effectiveness of the dehumidification. The machine will start defrosting until the temperature goes back to normal.
• When the machine is defrosting, the dehumidification pauses. The dehumidification light goes off, and the defrosting light will go on.
• Do not turn off the machine during the defrosting process.

---

When should I close the secondary intake?

Close the secondary intake when the environment temperature falls under 60 °F (16 °C) or in contaminated environments for better efficiency. To close it, remove the filter case, rotate, and reinstall.

---

How does drainage work?

• Press the Manual Drainage button to process drainage manually. It will last for 3 minutes (180 seconds) and won’t stop dehumidification or defrosting.
• In dehumidification mode, the machine will automatically process drainage for 2 minutes (120 seconds) every 15 minutes (900 seconds). This won’t stop the dehumidification process.
• If the water tank is full or not positioned horizontally, the water tank full indicator light will go on. Any dehumidification or defrosting process will pause, and the machine will automatically process drainage for 3 minutes (180 seconds). If the water tank is still detected as full, an error code will be displayed.
• When turned off, the machine will automatically process drainage for 2 minutes (120 seconds). Wait until this process is complete.

---

How do I calculate the usage time?

1. Write down the ending time right before the machine shuts down.
2. Compare the starting time and the ending time to calculate the usage time.

---

How do I turn off the dehumidifier?

1. Press the Power Control button to switch off the machine.
2. When turned off, the machine will automatically process drainage for 2 minutes (120 seconds). Please wait until this process completes.

---

What should I do before transportation?

• Process a drainage manually. Otherwise, the water may spill and enter the core parts of the machine during transportation, which may void the warranty.
• Disconnect the machine from the power source.
• Remove all the extension setups and uninstall the power cord and drain hose.

---

How do I transport the dehumidifier?

• Lift with Hand Carry Handles: Lift the dehumidifier with the two hand carry handles on the two ends on the top. Be aware of the machine’s weight.
• Transport with Trolley Handle: Lift the dehumidifier on the wheels with the trolley handle. Pull to transport with the trolley handle.

---

What should I do before maintenance or storage?

• Process a drainage manually.
• Disconnect the machine from the power source.
• Remove all the extension setups.

---

How do I organize the power cord and drain hose?

1. Remove the power cord/drain hose from the outlet of the machine.
2. Open the Velcro on the hangers.
3. Hang the power cord/drain hose on the hangers and close the Velcro.

---

How do I store or replace the filters?

1. Unscrew the two screws.
2. Take out the filter grille.
3. Slide off the primary filter from the grille.
4. Take out the secondary filter case and the secondary filter from the slot.
5. Clean and wash the filters with water.
6. Store the filter in a dry and cool area in a sealed container.
7. Replace filters if necessary.

---

How do I clean the surface of the dehumidifier?

• Use a damp cloth to wipe the surface of the housing. Do not clean the unit with water directly.
• Do not clean the fins of the evaporator and condenser by yourself.

---

How do I store the machine?

• Store the appliance in a dry and cool indoor place, away from direct sunlight as well as chemicals and out of reach of children.
• Make sure the machine is levelly positioned.
• If you want to stack this appliance, stack them on their tops with the same orientation.
• Do not stack more than three units of this appliance.

---

What should I do if the dehumidifier does not start?

• Possible Cause: No electricity.
  • Solution: Check for power supply.
• Possible Cause: The power cord is not properly plugged in.
  • Solution: Remove and reconnect the power cord.

---

What should I do if the dehumidifier runs but the humidity level does not decrease?

• Possible Cause: The dehumidification system is within the startup process.
  • Solution: Wait for 3 minutes (180 seconds) until the dehumidification light stops blinking.
• Possible Cause: The humidity level setting is too high.
  • Solution: Decrease the humidity level setting.
• Possible Cause: The working area is not enclosed.
  • Solution: Make sure the area is tightly sealed.
• Possible Cause: There are other sources of humidity in the room.
  • Solution: Remove these sources or wait until they completely volatilize.
• Possible Cause: The humidity level has reached the setting level.
  • Solution: Decrease the humidity level setting, set to constant dehumidification mode, wait until the humidity level rises up again.

---

What should I do if the dehumidifier runs but the humidity level does not decrease enough?

• Possible Cause: The machine was tilted and wasn’t positioned upright for enough time before use.
  • Solution: Position the machine upright on a level surface and wait for at least 4 hours before the next use.
• Possible Cause: The air filter or air inlet/outlet is blocked.
  • Solution: Remove blockage.
• Possible Cause: The environment temperature is too low/high, or the humidity level is too low.
  • Solution: The dehumidifier is designed to work in an environment with a temperature of 33 °F to 105 °F (0.6 °C to 40.6 °C) and a relative humidity level of 20% and higher. Make sure the room temperature/humidity does not exceed this range.

---

What should I do if there is water on the floor?

• Possible Cause: The drain hose is loose.
  • Solution: Tighten the connection of the drain hose.
• Possible Cause: The machine starts the drainage process.
  • Solution: The water pump can create sounds during operation. This is a normal sound.

---

What does Error Code: E2 mean and what should I do?

• Meaning: Failure of the temperature sensor.
• Solution: The dehumidification can function, but you won’t be able to see the temperature/humidity on the screen. Contact XPOWER for more assistance.

---

What does Error Code: E3 mean and what should I do?

• Meaning: Failure of the humidity sensor.
• Solution: Contact XPOWER for more assistance.

---

What does Error Code: E4 mean and what should I do?

• Meaning: Failure of the water pump.
• Solution: Contact XPOWER for more assistance.

---

What does Error Code: E5 mean and what should I do?

• Meaning: The machine is not positioned levelly.
  • Solution: Position the machine on a level surface.
• Meaning: The drain hose is blocked.
  • Solution: Remove blockage.

---

What does it mean if there is a failure of the defrost sensor and what should I do?

• Meaning: Failure of the defrost sensor.
• Solution: The dehumidification can function but will defrost for 5 minutes every half an hour. Contact XPOWER for more assistance.

---

What does the limited warranty cover?

The limited warranty covers defects in materials and workmanship in XPOWER-branded products purchased in the U.S. only. Local warranty policy (if any) in your country will cover products purchased outside the U.S.

---

What is not covered by the warranty?

Items mentioned but not limited to the following are not covered by warranty:

• Power cord, filters, or any other components considered as “consumable parts” by XPOWER.
• Normal wear and tear.
• Problems that result, directly or indirectly, at XPOWER’s sole discretion, from:
  • External causes such as accident, abuse, misuse, or problems with the electrical power supply.
  • Disassembling, servicing, or modification not authorized by XPOWER.
  • Usage that is not accordant with product instructions stated in the Owner’s Manual.
  • Failure to follow the product instructions or lack of necessary maintenance stated in the Owner’s Manual.

---

What should I do before contacting XPOWER?

• Consult the Owner’s Manual and follow the instructions in the troubleshooting guide.
• Access http://www.xpower.com for advice and information that could be helpful to address your problems.

---

What should I do if I need additional assistance from XPOWER?

• Email info@xpower.com.
• Call XPOWER U.S. Customer Service Department at 855-855-8868 or other numbers provided on http://www.xpower.com.
• Visit XPOWER U.S. Head Office at 240 Clary Ave., San Gabriel, CA 91776, or the most current address provided on http://www.xpower.com.
• Have your original proof of purchase and the serial number(s) of your product(s) ready when you contact XPOWER.

---

What should I do if I am instructed to return the unit for service or replacement?

1. Request a RMA (Return-Merchandise-Authorization) number.
2. Use the original or an equivalent packaging, prepay shipping charges at your own expense to the address provided by XPOWER, with the RMA number on the shipping label or the packaging.
3. Include all the original parts and components.

XPOWER will inspect, assess, and advise on the repairs needed and applicable cost, if any. For products under warranty, they will pay to ship the repaired or replaced product(s) to you if you use an address within the Contiguous United States. Otherwise, they will ship the product(s) to you at your own expense.