XO XOIL4219KSE (01) PDF Document

The dimensions for the XO XOIL4219KSE insert model are as follows:

MODEL: XOIL4219KSE

A: 34-5/16″

B: 40-3/8″

C: 12″

D: 19-1/4″

Top of hood duct diameter: Ø7-27/32″

The dimensions for the XO XOIL4222KSE insert model are as follows:

MODEL: XOIL4222KSE

A: 34-5/16″

B: 40-3/8″

C: 15-1/4″

D: 22-1/2″

Top of hood duct diameter: Ø7-27/32″

To install the XO XOIL4219KSE hood into a custom canopy or cabinet, the cutout dimensions should be:

MODEL: XOIL4219KSE

HEIGHT: 19-7/16″

WIDTH: 40-1/2″

Gap around the unit should be minimized (~ 1/16″) to ensure a snug fit.

To install the XO XOIL4222KSE hood into a custom canopy or cabinet, the cutout dimensions should be:

MODEL: XOIL4222KSE

HEIGHT: 22-5/8″

WIDTH: 40-1/2″

Gap around the unit should be minimized (~ 1/16″) to ensure a snug fit.

The recommended mounting height above gas and electric cooktops for the XO XOIL4219KSE is 27″ to 32″.

The recommended mounting height above gas and electric cooktops for the XO XOIL4222KSE is 27″ to 32″.

Before fitting the XO XOIL4219KSE or XO XOIL4222KSE hood into the cabinet:

1. Remove the four (4) screws holding the side bracket (B) in place. Remove the brackets and set aside.

2. Remove the two (2) screws holding the bracket (H) in place and tilt down.

To insert and fasten the hood:

Insert the hood into the cutout.

Fasten the hood in place: Using four (4) screws along the inside front edge and four (4) screws in the back corners as shown.

The color convention for electrical connections on the XO XOIL4219KSE is:

BLACK = HOT LEG

WHITE = NEUTRAL

GREEN/YELLOW = GROUND

Polarity must be observed. The unit must be properly grounded. Use a double throw disconnect switch.

1. Route the power cord to the junction box inside the hood.

2. Using listed conduit fittings and connectors, connect the power supply to the box and each line to the appropriate wire following this color convention:

BLACK = HOT LEG

WHITE = NEUTRAL

GREEN/YELLOW = GROUND

Polarity must be observed. Unit must be properly grounded. Use a double throw disconnect switch.

3. Replace the box cover

4. Replace the Anti-grease Baffles.

To remove the baffles from the XO XOIL4219KSE:

1. Pull down on the release latch (shown left)

2. Lower the front edge of the baffle

3. Pull forward and remove

4. To replace, insert the rear of the baffle, holding the latch open, swing the the front up into place and release the latch.

Baffle filters on the XO XOIL4219KSE should be cleaned at least once every 2 months, more frequently depending on the type of cooking performed and the build up of grease.

To clean the stainless steel surfaces of the XO XOIL4219KSE:

Clean periodically with warm soapy water and clean cotton cloth or micro fiber cloth. Always rub in the direction of the stainless steel grain.

To remove heavier grease build up use a liquid degreaser detergent.

After cleaning use a non-abrasive stainless steel polish/cleaners, to polish and buff out the stainless luster and grain. Always rub lightly, with a clean cotton cloth or a micro fiber cloth and buff in the direction of the stainless steel grain.

Do not use corrosive detergents, abrasive detergents or oven cleaners.

Do not use any product containing chlorine bleach or any product containing chloride.

Do not use steel wool or abrasive scrubbing pads which will scratch and damage surface.

Any painted surfaces of the XO XOIL4219KSE should be cleaned with warm water and detergent only.

The LED light modules (XOPSPK6602) are held in place by spring clips which must be squeezed in before the lamp can be pushed down through the fascia.

1. Unplug the plastic molex connector.

2. Plug in the new fixture and snap back into place.

The BUTTON on the XO XOIL4219KSE controls the LED lights and offers three illumination levels:

Press the button Once for HIGH;

Twice for MEDIUM;

Three times for LOW;

Four times for OFF.

The blower motor speed buttons on the XO XOIL4219KSE function as follows:

BUTTON 0: Turns both the Blower and Lights On and Off

BUTTON 1: Blower motor operates on LOW speed.

BUTTON 2: Blower motor operates on MEDIUM speed.

BUTTON 3: Blower motor operates on HIGH speed.

To activate POWER BOOST on the XO XOIL4219KSE, Press and Hold BUTTON 3 for 2 seconds. This increases airflow to a fourth and even higher speed for 10 minutes. When activated, the button will blink to alert you it is running. After 10 minutes the blower speed will return to its last setting. Note: The POWER BOOST function will operate even when the hood is off.

To manually stop the POWER BOOST before 10 minutes has elapsed:

Press BUTTON 3 and it will revert to HIGH speed, or

Press BUTTON 0 to shut the blower off completely

BUTTON T on the XO XOIL4219KSE Activates and Deactivates the TIMER Function.

Pressing BUTTON T (whether the blower is off or running) will cause the motor to run at LOW speed for 5 minutes before shutting off the blower and lights automatically.

While the TIMER is activated, you can change speed or engage POWER BOOST, the hood will still shut off after 5 minutes.

To manually turn the unit off before 5 minutes has elapsed:

Press BUTTON T or BUTTON 0.

To synchronize the optional remote control (XOVREMOTE1) with the XO XOIL4219KSE hood, follow these simple steps:

1. Standing near the hood, while it is not running, press and hold BUTTON on the hood for 4 seconds -the button should start to blink for 5 seconds.

2. When the button on the hood starts to blink, Press any button on the remote. The hood and remote are now synchronized.

3. If the synchronization fails for any reason, repeat steps 1 and 2.

The ducting guidelines for the XO XOIL4219KSE are:

This hood is designed to use an 8″ round duct – it may be transitioned to a 4″ x 14″ rectangular duct.

Never reduce duct size. Undersized ducting severely restricts air flow and harms performance. (Example: the area of an 8” Duct is more than 75% larger than a 6” Duct)

Keep duct runs as short and straight as possible.

Avoid using flexible metal ducting if run is longer than 6′.

Never use plastic ducting.

Use smooth bore metal ducting.

Minimize the number of fittings (see chart).

When you must use fittings, try to separate them with sections of 4′ or more of straight duct.

Always follow the manufacturer’s guidelines for the cooking equipment you are venting.

If make up air control dampers are required, position the sensor in a straight run of duct ideally with 4′ of straight duct between each side of the sensor and a duct fitting. Remember to include power and control wiring for this in your plans.

Total equivalent feet should be less than 100′.

To estimate the Total Equivalent Feet in a Duct Run for the XO XOIL4219KSE (for 1000 CFM or less):

Under “QTY USED” enter how of each section you will be using.

In the first two rows – enter how many feet of each type of straight duct you will be using (i.e. for 20 ft enter 20, for 30ft enter 30).

Enter the number of each type of turn you are using and the type of end cap.

Multiply across each row the “MULTIPLIER” x “QTY USED” to get the equivalent feet for those components.

Add up all the values in the “EQUIVALENT FEET” column.

Note: If using flexible metal duct – increase all multipliers by 50% (12 becomes 18 – etc.)

The Total Equivalent Feet should be less than 100.

DUCT PIECE – DESCRIPTION – MULTIPLIER – QTY USED – EQUIVALENT FEET

1′ of 8″ Round Duct – 1

1′ of 4″ x 14″ Rect. Duct – 1

8″ 90 Degree Elbow – 12

8″ 45 Degree Elbow – 7

4″ x 14″ 90 Degree – 14

4″ x 14″ 45 Degree – 8

4″ x 14″ x 8″ Round – 2

4″ x 14″ x 8″ 90 Degree – 4

8″ Round Wall Cap w Damper – 24

4″ x 14″ Wall Cap w Damper – 24

8″ Round Roof Cap – 33

To reduce the risk of a range top grease fire when using the XO XOIL4219KSE:

A. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

B. Always turn hood ON when cooking with high heat.

C. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.

D. Use proper pan size. Always use cookware appropriate for the size of the surface element.

E. Keep fan, filters and grease laden surface clean.

F. Use high range setting on range only when necessary. Heat oil slowly on low to medium setting.

G. Don’t leave range unattended when cooking.

H. Always use cookware and utensils appropriate for the type and amount off food being prepared.

To reduce the risk of injury to persons in the event of a range top grease fire when using the XO XOIL4219KSE, observe the following:

A. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

B. NEVER PICK UP A FLAMING PAN – You may be burned.

C. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.

D. Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

2. The fire is small and contained in the area where it started.

3. The fire department is being called.

4. You can fight the fire with your back to an exit.

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

A. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.

B. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

C. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

D. Ducted fans must always be vented to the outdoors.

E. This unit must be grounded.

WARNING – TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

WARNING – UNDER CERTAIN CIRCUMSTANCES DOMESTIC APPLIANCES MAY BE DANGEROUS.

A. Do not check filters with hood working.

B. Do not touch the lamps after a prolonged use of the appliance.

C. No food must be cooked flambè underneath the hood.

D. The use of an unprotected flame is dangerous for the filters and could cause fires.

E. Watch constantly the fried food in order to avoid the cooking oil flares up.

F. Before performing any mainteinance operation, disconnect the hood from the electrical service.

IMPORTANT SAFETY INSTRUCTIONS (FOR RESIDENTIAL USE ONLY):

Read and save these instructions. Please read entire instructions before proceeding.

Take care when using cleaning agents or detergents.

Suitable for use in household cooking area.

WARNING – To reduce the risk of fire or electric shock, do not use this fan with any Solid-State Speed Control Device.

CAUTION – To reduce risk of fire and to properly exhaust air, be sure to duct air outside – Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages.

CAUTION – For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.

CAUTION – To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit.

CAUTION – Please read specification label on product for further information and requirements.

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

A. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer.

B. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.