XIAOMI LSNFJ04ZMEU (01) PDF Document

The XIAOMI LSNFJ04ZMEU is intended for indoor use only. During use, place the heater on a stable and level surface, and do not tilt or tip it over.

No, do not use the XIAOMI LSNFJ04ZMEU near bathtubs, sprinklers, or swimming pools.

Do not expose bare skin to direct contact with the XIAOMI LSNFJ04ZMEU to avoid burns. Additionally, do not touch the heater during or right after use.

No, do not use the XIAOMI LSNFJ04ZMEU to warm or heat animals or plants.

To prevent the risk of overheating or fire, never use an extension cord with the XIAOMI LSNFJ04ZMEU.

Use the XIAOMI LSNFJ04ZMEU in a well-ventilated environment, and do not let debris enter or block the air inlet or outlet.

Do not insert any wires or other foreign objects into any openings of the XIAOMI LSNFJ04ZMEU to avoid electric shock.

Do not place or use the XIAOMI LSNFJ04ZMEU near gasoline, paint, other flammable or explosive materials, or in dusty areas, such as garages or workshops. Never place the heater next to objects prone to deformation, discoloration, or deterioration by heat.

The XIAOMI LSNFJ04ZMEU is a high-power product. When using it for the first time or with a new power outlet, check whether the plug fits the outlet properly.

1. Plug the XIAOMI LSNFJ04ZMEU into the outlet.

2. Enable hot air mode and disable it after about 30 minutes.

3. Unplug the heater after it cools down to check whether the plug prongs are overheating (temperature over 55°C). If so, change the outlet to avoid the risk of a burnt plug or fire due to overheating.

Do not use the XIAOMI LSNFJ04ZMEU when its power cord or plug is damaged. If damaged, the power cord must be replaced by personnel from the manufacturer, the after-sales service department, or other professional department to avoid hazards.

Make sure there are no other appliances used in the same circuit as the XIAOMI LSNFJ04ZMEU to prevent overloading.

Non-professionals are not allowed to disassemble the XIAOMI LSNFJ04ZMEU to avoid hazards. Contact the after-sales service team in case of malfunction.

The XIAOMI LSNFJ04ZMEU in natural breeze mode cannot fully replace the fan.

Do not disconnect the power before the XIAOMI LSNFJ04ZMEU cools down; otherwise, it may trigger power-off protection. The heater needs to be completely cooled off before it can be resumed use.

The XIAOMI LSNFJ04ZMEU is not intended for use by persons (including children) who lack the physical, perceptive or mental ability, or the experience or knowledge required to operate it, except under the supervision or guidance of a guardian responsible for their safety.

Do not directly rinse the XIAOMI LSNFJ04ZMEU with water. Do not immerse it in water. Do not spill water into the heater. Do not cover the heater to avoid overheating. Do not use the heater in greenhouses or on construction sites. Do not place the heater directly under a power outlet.

Check to make sure the XIAOMI LSNFJ04ZMEU is in good condition and the power cord is undamaged. Use a 220 V AC outlet with a rated current of at least 10 A. It is recommended to plug the heater into a wall outlet and not share the power strip with other appliances. Place it at a distance of 1–2 meters for optimal heating performance.

Plug the XIAOMI LSNFJ04ZMEU into the power outlet. Press the on/standby button to run the heater. Press the on/standby button during its heating, and the heater will blow air for heat dissipation for 30 seconds before entering standby. Press the on/standby button when blowing air for heat dissipation, and the heater will enter the previous mode.

Press the mode button when the XIAOMI LSNFJ04ZMEU is running to cycle through:

Natural breeze mode: Blowing air only, no heating.

Warm air mode: Blowing warm air at a power of about 1200 W.

Hot air mode: Blowing hot air at a power of about 2000 W.

Constant temperature mode: Blowing hot air at an adjustable target temperature.

Press the temperature button when the XIAOMI LSNFJ04ZMEU is running to cycle through target temperatures: 22°C, 24°C, 26°C, and 28°C. It automatically enters constant temperature mode after the target temperature is set. Target temperature adjustment is not available in other modes.

Press the timer button when the XIAOMI LSNFJ04ZMEU is running to cycle through scheduled standby time: 1 hour, 2 hours, 4 hours, 8 hours, and disabled. If no operation is performed within three seconds after the scheduled standby time is selected, the timer/temperature indicator will light up for the targeted temperature. Press the timer button during scheduled standby to indicate the approximate remaining time.

To enable or disable oscillation, press the oscillation button when the XIAOMI LSNFJ04ZMEU is running.

To enable or disable child lock, simultaneously press and hold the timer button and the temperature button for seven seconds when the XIAOMI LSNFJ04ZMEU is powered on.

The Wi-Fi is enabled by default. When the XIAOMI LSNFJ04ZMEU is powered on, simultaneously press and hold the timer button and oscillation button for 7 seconds to enable or disable Wi-Fi. To reset Wi-Fi, press and hold the oscillation button for seven seconds when the heater is powered on.

Simultaneously press and hold the oscillation button and the mode button for seven seconds when the XIAOMI LSNFJ04ZMEU is powered on.

Unplug the XIAOMI LSNFJ04ZMEU and wait for it to fully cool down before cleaning. Wipe it with a clean, soft, and damp cloth. Do not drip water into the heater when cleaning. Do not disassemble the heater during maintenance. Use or store the heater only when it is fully dry. Do not bump or scratch the heater. Store in the original packaging in a dry place.

Model: LSNFJ04ZMEU. Rated Power: 2000 W. Rated Voltage: 220–230 V~. Rated Frequency: 50 Hz. Net Weight: Approx. 2.3 kg. Dimensions: 176 x 467 mm. Connectivity: Wi-Fi IEEE 802.11 b/g/n 2.4 GHz.