WZATCO YUVA GO MAX (01) PDF Document

To use the WZATCO YUVA GO MAX projector correctly, please follow these guidelines:

1. Do not point the lens towards the human eye to avoid damage to the eyes caused by the strong light of the lens after the machine is turned on.

2. Please do not block the air inlet/outlet of the device to avoid damage to the internal electronic devices due to the failure of the device to dissipate heat normally.

3. Do not use paper, cloth and other cleaning tools to directly wipe the lens to avoid damage to the lens; please use a cleaning air blower to remove dust on the surface of the lens.

4. Please keep the device and its parts and accessories out of the reach of children.

5. Please ensure that the device is used in a dry and ventilated environment.

6. Do not store and use the device in overheated or cold places. High (low) temperature will shorten the life of electronic devices; the allowable operating environment is 0°C~35°C.

7. Do not forcefully squeeze the device or place shields above or on its back to avoid damage to the device.

8. Do not drop, knock or strongly vibrate the device to cause damage to the internal circuit board.

9. Do not attempt to disassemble the device without permission; if there is any problem, please contact the after-sales service.

10. Do not repair any products by yourself; if the equipment or any parts are not working properly, you should consult the after-sales service or return to the factory for repair.

11. The equipment must not be exposed to water droplets or splashes, and objects filled with liquids such as vases should not be placed on the equipment.

The main components and ports of the WZATCO YUVA GO MAX projector are:

1. USB input

2. Earphone /3.5mm sound output

3. Hd input

4. Power botton

5. Sound speaker

6. Cooling window

7. Power input

8. IR receiver

The functions of the buttons on the remote control are as follows:

1. Power

2. Mute key

3. Home button

4. Set key

5. Arrow button

6. Menu

7. Return key

8. Mouse button

9. Volume up

10. Focus Plus

11. Volume down

12. Focus reduction

13. Signal

Step 1: Take out the machine from the packing box, remove the packing bag and lens cover, place the projector on a basic level table, plug in the matching power cord, and then connect to the AC power supply. At this time, the indicator light on the projector panel is Standby red.

Step 2: Press the on-off button on the body or the on-off button on the remote control to start the projector. At this time, the indicator light on the projector panel turns solid blue and the lens emits light, and the projector is started.

1. This function is automatically turned on by default, and the screen can be kept square even after the device is displaced.

2. Press the menu key, go to Projector Setting—>Omnidirectional automatic correction to set the shape.

1. This function is automatically turned on by default. If the projector moves, it will trigger the gyroscope and start Auto focus, the picture automatically changes from blur to clear.

2. The focus will be completed automatically. After completion, you can also fine-tune by pressing the F+ (Manual focus “+”) and F- (Manual focus “-“) buttons on the remote control.

Press the signal source key “S” on the remote control to enter the signal source menu interface. Use the arrow keys and the confirm key to select the desired signal source.

To connect a computer, use the HDMI (high-definition interface).

Steps: switch the projector signal source > connect the corresponding data cable > switch the notebook output mode.

Method 1: For an XP system, press Fn + dual screen key (F1–F12 draws two screens), switch 2-3 times.

Method 2: For Windows 7 and above, just press Win + P on your keyboard, select the “Copy” option to connect. If this does not work, please update your computer’s graphics card driver.

Connect the 3in1 video adapter cable to the AV interface of the projector, and select the multimedia signal channel: “AV”.

The projector can be connected to 3.5mm headphones and other wired audio equipment via the 3.5mm audio device connection port.

You can use AirPlay to display the same screen as your iPhone/iPad. Note: Make sure the projector is connected to the phone under the same WiFi network or hotspot.

Step 1: In the projection side of my app, open the “tranScreen” APP.

Step 2: Bring up the phone console interface and click the screen mirroring button.

Step 3: Select the device you want to cast, select to be on the same screen.

The name of the projection device can be defined in the projection APP. It is recommended to connect to 5G WiFi to avoid stuttering on the same screen.

You can use Miracast to display the same screen as your Android phone/tablet.

Step 1: Go to Settings > Network > turn on the WiFi switch on the projection side, and open the “Miracast” APP in My App.

Step 2: On the mobile phone (using Xiaomi as an example), open the WiFi port, enter the settings > other connection methods > wireless display > select the projection device name.

Step 3: During the connection process, a connection invitation appears on the projector, click Accept.

Note: Different mobile phones have different Miracast setting paths and names. Common names are: media output/projection screen/multi-screen interaction, etc. Please refer to the mobile phone for details. Due to the large number of mobile phone types, it is not guaranteed that all mobile phone models can be compatible with the same screen.

Proper maintenance will affect the performance, longevity, and effectiveness of your WZATCO YUVA GO MAX projector.

1. Dustproof: Excessive dust will affect heat dissipation. Clean the dust filter of the projector in one and a half months in actual environment.

2. Ventilation: The projector generates heat. Ensure there are no objects blocking the air vent and air outlet. Heat dissipation depends on the convection of cold air to improve performance, stability, and longevity.

3. Lens maintenance: The lens is a core component related to picture clarity. Too much dust will affect image quality. If the lens is dirty, use a soft cotton cloth to wipe the glass surface. Do not use a hard cloth or corrosive materials.

4. Cleaning: Clean up excessive dust on the surface of the projector in time, as too much dust will affect the fuselage heat dissipation.

5. Moisture-proof: The projector is easily affected by humid air. The working humidity should be between 45%-60%. Air that is too humid will affect working stability.

6. Shockproof: The projector must be strictly prevented from strong impact, extrusion, and vibration. Do not move or knock the projector during normal work, as it may cause internal electrical failure.

7. Do not install the projector on an unstable, shaky or uneven table.

8. Do not place containers filled with liquid on the projector.

High brightness lamp! Avoid staring or directly looking at the light, especially for children.

1. Please wash the anti-dust mesh once a month in order to protect your projector!

2. Before using this machine, please remove the protective membrane from the top & bottom cover.