WILLIAMS SOUND HEARING HELPER PFM 350 (01) PDF MANUAL


Post questions, comments, reviews or errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD WILLIAMS SOUND HEARING HELPER PFM 350 (01) PDF MANUAL


PDF Content Summary: MANUAL AND USER GUIDE HEARING HELPERTM Personal FM System Wireless FM Listening System Models PFM 350, PFM 300, PFM 350E RCH, & PFM 300E RCH Transmitter Model PFM T32 Optional Receiver Models PFM R32, R31 MAN 072I 2 HEARING HELPERTM PERSONAL FM SYSTEM MODELS PFM 350, PFM 300, PFM 350E RCH, PFM 300E RCH INSTALLATION GUIDE & USER MANUAL Contents Page SYSTEM OVERVIEW 3 SYSTEM COMPONENTS 4 SAFETY INFORMATION 5 RECYCLING INSTRUCTIONS 5 OPERATING INSTRUCTIONS PFM T32 TRANSMITTER 6 PFM R32 RECEIVER 9 PFM R31 RECEIVER 10 BATTERY INFORMATION BATTERY INSTALLATION 13 RECHARGEABLE AND NON-RECHARGEABLE BATTERIES 13 USING OPTIONAL CHG 200 BATTERY CHARGER 14 USING YOUR PERSONAL FM SYSTEM WITH A HEARING AID 15 APPLICATIONS FOR VARIOUS HEARING LOSS LEVELS 15 IN CASE OF DIFFICULTY 16 WARRANTY 17 SYSTEM SPECIFICATIONS 18 ACOUSTIC SPECIFICATIONS 19 SYSTEM OVERVIEW Thank you for purchasing the Hearing HelperTM Personal FM System from Williams Sound Corp. Anyone needing auditory assistance to overcome background noise, reverberation, or distance from the sound source can benefit from the Personal FM System. Your PFM System has two principal parts: the Transmitter and the Receiver. Much like a miniature radio station, the Transmitter and microphone pick up the sounds you want to hear and broadcast them over an FM radio signal. The receiver and earphone are used to pick up the broadcast up to 100 feet away. To avoid difficulties, please read through these instructions as you begin to use the system. Then save them for questions that arise as you continue to use your Williams Sound Personal FM System. If you have problems with the PFM system, don’t hesitate to call us toll-free at 1-800-843-3544. FIGURE 1: HOW THE PFM SYSTEM WORKS

Speaker Uses Transmitter With Microphone FM Radio Signal Listeners use R31 or R32 Receivers with Earphones, Headphones, Or Neckloop

The speaker wears the body-pack transmitter and a clip-on microphone. The speaker’s voice is broadcast as an FM radio signal over a distance of 100-150 feet (30-45 m). Listeners use the pocket receiver and earphone or headphone to hear the speaker’s voice directly, with reduced background noise. A neckloop telecoil coupler allows the system to be used with telecoil (T-Switch) equipped hearing aids. 3 4 SYSTEM COMPONENTS ► Body Pack Transmitter (PFM T32) with (2) AA batteries (BAT 001) ► Lavalier microphone (MIC 090) ► Mini earphone (EAR 013) ► Soft Nylon System Carry Case (CCS 020) ► (2) Belt clip cases (CCS 001) ► Instructions (MAN 072) ► PFM System 300 Only: Personal FM Receiver (PFM R32) with (2) AA batteries (BAT 001) ► PFM System 350 Only: Personal FM Receiver (PFM R31) with Plug Mount Microphone (MIC 014) and (2) AA batteries (BAT 001) ► PFM System 300E RCH Only: Personal FM Receiver (PFM R32) with CHG 200A Drop-in Charger and (2) AA NiMH rechargeable batteries (BAT 026) ► PFM System 350E RCH Only: Personal FM Receiver (PFM R31) with CHG 200A Drop-in Charger and (2) AA NiMH rechargeable batteries (BAT 026) FIGURE 2: SYSTEM COMPONENTS Williams Williams Sound Sound Williams Williams Sound Sound Williams Williams Sound Sound Hearing Hearing Helper Helper ® ® Hearing Hearing Helper Helper ® ® Hearing Hearing Helper Helper ® ® T32 Transmitter R32 Receiver R31 Receiver (PFM 300 & 350 Systems) (PFM 300 System) (PFM 350 System) SAFETY INFORMATION HEARING SAFETYCAUTION! This product is designed to amplify sounds to a high volume level which could poten- tially cause hearing damage if used improperly. To protect your hearing and the hear- ing of others: 1.Make sure the volume is turned down before putting on the earphone or headphone before adjusting the volume to a comfortable level. 2.Set the volume level at the minimum setting that you need to hear. 3.If you experience feedback (a squealing or howling sound), reduce the volume setting and move the microphone away from the earphone or headphone.

4. Do not allow children or other unauthorized persons to have access to this product.

BATTERY SAFETY AND DISPOSAL CAUTION! This product is supplied with disposable Alkaline batteries. Do not attempt to recharge disposable batteries, which may explode, release dangerous chemicals, cause burns, or other serious harm to the user or product. PACEMAKER SAFETY: CAUTION! 1.Before using this product with a pacemaker or other medical device, consult your physician or the manufacturer of your pacemaker or other medical device.

2. If you have a pacemaker or other medical device, make sure that you are using this product in accordance with safety guidelines established by your physician or the pacemaker manufacturer.

RECYCLING INSTRUCTIONS BATTERY SAFETY AND DISPOSAL Help Williams Sound protect the environment! Please take the time to dispose of your equipment properly. Product Recycling for Customers in the European Union: Please do NOT dispose of your Williams Sound equipment in the household trash. Please take the equipment to a electronics recycling center; OR return the product to the factory for proper disposal. Battery Recycling for Customers in the European Union: Please do NOT dispose of used batteries in the household trash. Please take the batteries to a retail or community collection point for recycling. 12/27/06 5 6 USING THE PFM T32 TRANSMITTER 1. Install two (2) AA batteries. If you’re using rechargeable batteries, they must be charged before using. See battery information on page 13. 2. Plug the microphone cord into the “Mic” jack on top of the transmitter. FIGURE 3: T32 TOP VIEW 3. Place the transmitter in the belt clip case provided. 4. Slide the Power Switch on top of the transmitter to “On.” The Power ON LED indicator should illu- minate Red. 5. The microphone should be placed as close to the speaker’s mouth as is practical. For lapel mics, attach the microphone to a collar, lapel, or tie. 6. When you are ready to speak, turn the Mic Mute Switch (speaker icon) to the “On” position. When you are done speaking, mute the mic by turning the Mute Switch to the “Off” position (speaker icon with line through it). The transmitter can be placed in a pants pocket, or clipped onto a belt or waistband. FIGURE 4: CORRECT MICROPHONE PLACEMENT Yes Yes No The PFM System comes with an omnidirectional, lapel-clip style microphone. It should be clipped to a collar, lapel, tie, or neckline as close to the mouth as possible and centered on the body as shown. Note On The Transmitter Antenna: The microphone cord is the transmitting antenna. Do not bunch up the cord or wrap it around the transmitter. For maximum range, the cord should hang as straight as possible. CHANGING THE PFM T32 FREQUENCY FIG. 5: PFM T32 FREQUENCY CHANGE By default, the T32’s frequency is to set 72.9 MHz (Channel E). If you experience FM interference, or if you need to match a receiver’s frequency, it may be necessary to adjust the frequency on the T32. Instructions: 1. Open the battery compartment using a coin in the slot in the bottom of the transmitter. Remove the batteries. 2. Lift the battery compartment door up and pull to your left to expose the circuit board. 3. Refer to FIG 5 to locate the Channel Switch. 4. Use a small screwdriver to rotate the Channel Switch to correspond with the desired operating fre- quency. Choose between 16 standard channels. Refer to the Channel Selection Chart in FIG 5 for available channels. 5. Reinstall the batteries, then close the back of the transmitter. 6. Plug the microphone in and turn the transmitter on to provide a tuning signal for the receivers. Important: Make sure all receivers being used match the frequency of the transmitter. Refer to the receiver’s instruction manual for frequency change instructions. 7 ADVANCED FEATURES ON THE PFM T32Gain Control Adjustment If necessary, the microphone gain control on the T32 FIG. 6: T32 ADVANCED FEATURES can be increased or decreased to meet the demands of specific listening applications. Instructions: 1. Open the battery compartment using a coin in the slot in the bottom of the transmitter. Remove the batteries. 2. Lift the battery compartment door up and pull to your left to expose the circuit board. 3. Refer to FIG 6 to locate the microphone gain con- trol. 4. Using a small screwdriver, turn the gain control fully counterclockwise to reduce the gain. Turn the gain control fully clockwise to increase the gain 5. Close the back of the case and battery door. COMPRESSION ADJUSTMENT By default, the T32 transmitter compression jumper is set to “Off” for normal operation, or 1:1 compression. For hearing assistance applications, the compression jumper can be set to “On” for 2:1 compression. Instructions: 1. Open the battery compartment using a coin in the slot in the bottom of the transmitter. Remove the batteries. 2. Lift the battery compartment door up and pull to your left to expose the circuit board. 3. Refer to FIG 6 to locate the Compression Selector. 4. Gently remove the jumper from the circuit board by pulling it up and away from the unit. You will see three exposed “pins.” To turn compression “On” (2:1 Compression): Press jumper on to the top two pin locations as shown on left. To turn compression “Off” (1:1 Compression): Press jumper on to the bottom two pin locations as shown on left. 5. Close the back of the case and battery door. 8 USING THE PFM R32 RECEIVER (PFM 300 & PFM 300E RCH): Receiver model PFM R32 has a single volume control and an earphone output jack. 1. Make sure there are two charged AA batteries in the Receiver. If batteries are not installed, see Battery Information on page 13. 2. Plug the earphone or headphone into the “Ear” jack on top of the Receiver. FIGURE 7: R32 RECEIVER TOP VIEW 3. Turn the power on by rotating the volume control knob on top of the Receiver. 4. Place the earphone in your ear. 5. Choose the correct channel using the right switch on the R32’s back panel. Unless you have changed the Transmitter channel, set the receiver to channel 1. If the Transmitter is on and tuned to channel 1, the FM Indicator light on the R32 will light. 6. Adjust the receiver volume control to a comfortable listening level. You should be able to hear someone speaking into the Transmitter microphone. 7. Adjust the receiver tone control to your needs. Lo – more low frequencies; Mid – some low frequency cut; Hi – maximum low frequency cut, emphasizes higher frequencies. (See Figure 8.) 8. Place the Receiver in the belt clip case provided. The Receiver can be placed in a pants pocket, or clipped onto a belt, harness, or waistband. Notes: The earphone cord is the receiving antenna. Do not bunch up the cord or wrap it around the receiver. For best reception, the cord should hang as straight as possible. Make sure the Receiver is turned OFF when not in use. The channel selector can be used to switch between an individual and a group channel. On Earphone Jack EAR FM Indicator FM Indicator FM On Volume Off Max Control FIGURE 8: RECEIVER TONE & CHANNEL CONTROLS TONE Channel Lo Mid Hi CH1 CH2 9 10USING THE PFM R31 RECEIVER (PFM 350 & PFM 350E RCH): Receiver model PFM R31 has two volume control knobs (one for the FM signal, one for environmental sounds), a microphone input jack, and an earphone output jack. 1. Make sure there are two charged AA batteries in the Receiver. If batteries are not installed, see Battery Information on page 13. 2. Insert the small Plug Mount Microphone (MIC 014) into the “Mic” jack on top of the R31 Receiver. FIGURE 9: R31 TOP VIEW FM Volume On Indicator Mic Jack Mic EAR FM OnMic MIC Volume FM Indicator FM Off Max Min Max Mic Jack 3. Plug the earphone or headphone into the “Ear” jack on top of the Receiver. 4. Turn the power on by rotating the taller “FM” volume control on top of the Receiver. 5. Place the earphone in your ear. FIGURE 10: RECEIVER TONE & CHANNEL CONTROLS TONE Channel Lo Mid Hi CH1 CH2 6. Choose the correct channel using the right switch on the R31’s back panel. If the Transmitter is on and tuned to channel 1, the FM Indicator light on the R31 will light. 7. Adjust the receiver tone control to your needs. Lo – more low frequencies; Mid – some low frequency cut; Hi – maximum low frequency cut, emphasizes higher fre- quencies. (See Figure 10.) 8. Place the Receiver in the belt clip case provided. The Receiver can be placed in a pants pocket, or clipped onto a belt, harness, or waistband. Notes: The earphone cord is the receiving antenna. Do not bunch up the cord or wrap it around the receiver. For best reception, the cord should hang as straight as possible. Make sure the Receiver is turned OFF when not in use. The channel selector can be used to switch between an individual and a group channel. Adjusting The R31 Volume Controls 1. Adjust the taller “FM” volume control to a comfortable listening level. You should be able to hear someone speaking into the Transmitter microphone. 2. Now adjust the shorter “Mic” volume control until you can hear sounds picked up by the environ- mental microphone on top of the receiver. 3. Adjust the two volume controls for a comfortable mix of FM and environmental sounds. You will normally want to have the FM signal louder than the environmental Mic signal to avoid picking up extra background noise. If no environmental sounds are desired, turn the “Mic” control fully to “Min”. If you want to hear nearby conversation or your own voice, turn the “Mic” control up. 11 12 TUNING THE PFM R32 & R31 RECEIVERS Tuning for the R32 and R31 Receivers is determined by tuning coils, and is stabilized by phase- locked-loop circuitry. A plastic tuning wrench (PLT 005) is needed to adjust the receiver tuning coil. 1. Use the Transmitter as a tuning signal source. Have someone speak into the microphone so you have something to listen to. 2. Keep the Transmitter and Receiver about 15 - 20 feet apart while tuning. The receiver must be tuned under weak signal conditions. 3. Open the battery compartment using a coin in the slot in the bottom of the transmitter. Pull up the receiver battery flap to open the receiver back like a book. This will expose the circuit board. 4. Move the channel selector switch to channel 2 (right position). 5. Use Figure 11 below to locate the tuning coils. Use the earphone supplied with the receiver to listen for the transmitter signal while you slowly and gently rotate the tuning slugs inside the tun- ing coil with the tuning wrench. Adjust the tuning coil for channel 2 slowly and carefully. Do not press down on the tuning slug. Adjust for maximum signal. 6. Re-tune all the receivers and mark the new frequency inside the case for future reference. FIGURE 11: LOCATION OF RECEIVER TUNING COILS

Batteries R31/R32 Receiver Channel 1 Tuning Coil Channel 2 Tuning Coil Channel Selector Switch

BATTERY INFORMATION INSTALLATION Open the battery compartment using a coin in the slot in the bottom of the receiver or transmit- ter. Press the batteries into place, observing proper battery polarity. Incorrect insertion of the battery is difficult, and if forced, may cause both mechanical and electrical damage to transmit- ters or receivers not covered by the five year warranty. Units will not work with the battery incorrectly installed. FIGURE 12: BATTERY INSTALLATION Rear of Transmitter or Receiver –+ Battery Compartment Note Proper + – Pry Slot Polarity DISPOSABLE BATTERIES In normal use, two AA 1.5 V alkaline batteries will last about 30 hours in the T32. The batteries will last approximately 80 hours in the R32 and R31 Receivers, respectively. If the sound becomes weak or distorted, replace the battery. The indicator light may still be on, even with a battery that is weak. Do not leave dead batteries in the receivers! Battery corrosion is not covered by the Williams Sound five year warranty. RECHARGEABLE BATTERIES The PFM 350 and PFM 300 Systems can use rechargeable AA batteries (BAT 026). On an overnight charge, these NiMH batteries are designed to operate for 20 hours in a T32 Transmiter. The R32 and R31 Receivers will last for 50 and 60 hours, respectively. Note: The battery installed in the receiver may be recharged in the receiver only if it is a NiMH battery, and only if the Williams Sound CHG 200A charger is used. Damage from improper charging is not covered by the Williams Sound five year warranty. For charging directions, see figure 13. !! IMPORTANT WARNINGS !! DO NOT ATTEMPT TO RECHARGE ZINC CARBON (“HEAVY DUTY”), ALKALINE, OR LITHIUM BATTERIES! DO NOT ATTEMPT TO RECHARGE DISPOSABLE BATTERIES! These batteries may heat up and explode, causing possible injury and damage to the equipment. Avoid shorting the plus and minus battery terminals together with metal objects. Battery damage and burns can result! Use only Williams Sound Supplied chargers and batteries! 13

14FIGURE 13: USING THE OPTIONAL CHG 200A BATTERY CHARGER TO CHARGE TRANSMITTERS AND RECEIVERS Step 1: Plug the CHG 200’s power supply into the Power Input on the charger’s side and a standard AC wall outlet. Step 2: Route the power cord around the Cord Hook (see figure at right). This will minimize strain on the cord and jack and insure that the power cord is not detached during charging. Step 3: Make sure the receivers/transmitters to be charged are turned OFF. Step 4: Place the receivers/transmitters in the slots so that the CHG 200’s Charging Pins and receiver’s side panel contacts are coupled. Make sure that the charg- ing contact holes line up with the charging pins. The receivers should drop easily into the slots. DO NOT FORCE THEM IN BACKWARDS. Step 5: The Charging Indicators will light, indi- cating that charging is in process. It takes 14–16 hours to fully charge the batteries. Remove the receivers when charging is completed. FURTHER SUGGESTIONS Receivers and Transmitters SHOULD NOT be left charging continuously when not in use. Receivers should always be turned OFF while charging. It’s best to allow the batteries to fully discharge before charging. If the batteries are near end of life and the LED turns off while the receiver is operating, this is an indication to change or recharge your batteries. Approximately one hour of battery life remains. Repeatedly charging the batteries after short periods of use (1-2 hours) will shorten battery life. Rechargeable batteries will need to be replaced after 1–2 years of use. Charging Contact Holes !! WARNING !! DO NOT ATTEMPT TO RECHARGE DISPOSABLE BATTERIES! The batteries may heat up and burst, causing possible injury and damage to the equipment. Avoid shorting the plus and minus battery terminals together with metal objects. Battery damage and burns can result! Use only Williams Sound supplied chargers and batteries. Charging Indicators Charging Pins Cord Hook Power Input

USING YOUR PERSONAL FM SYSTEM WITH A HEARING AID If you have a hearing aid equipped with a Telecoil (T-Switch), you can use a Neckloop (NKL 003–children’s size, or NKL 001–adult’s size) to magnetically couple the signal from the PFM Receiver into your hearing aid. The Neckloop plugs into the earphone jack of the receiver. Turn the switch to the “T” position on your hearing aid and adjust the volume control on the receiver to a comfortable level. If you have two hearing aids with telecoils, the signal will couple into both hearing aids (when using a silhou- ette). Direct Audio Input cords can be used with compatible hearing aids as well as with Cochlear Implant Processors. If your hearing aid has a direct audio input boot, you can obtain a cord from your hear- ing aid manufacturer to plug directly into the PFM receiver. The cord should have a 3.5 mm plug. APPLICATIONS FOR VARIOUS HEARING LOSS LEVELS The Personal FM is designed to provide hearing assistance for anyone when background noise or distance from the sound source make listening difficult. The microphone and transmitter are placed close to the desired sound source to help minimize background noise and to effectively eliminate the distance between the listener and the sound source. Because hearing ability varies, three cate- gories of amplification have been delineated: NO HEARING LOSS – LOW AMPLIFICATION Among Low Amplification applications are classroom and similar uses. The PFM System can be used with headphones or earphones for Central Auditory Processing Disorders, Learning Disabilities, or Attention Deficit Disorders. The PFM System is used primarily to boost speech sounds above other background noises, making it easier for the listener to focus on what is being said. The optional Rugged Headphone (HED 022–children’s size, and HED 021–adult’s size) are recommended for this application. The EAR 013 Single Mini Earphone, EAR 008 Surround Earphone, or EAR 014 Dual Mini Earphone can also be used. MILD – MODERATE HEARING LOSS These applications include the classroom, TV listening, car riding, and one-on-one conversations. The PFM System can be used with the Single or Dual Mini Earphone (EAR 013 or EAR 014) for moderate amplification fittings. The PFM System is also suitable for temporary mild hearing loss due to Otitis Media. The Rugged Headphones (HED 021) or Surround Earphone (EAR 022 or EAR 008) are recommended since they do not enter the ear canal. SEVERE – PROFOUND HEARING LOSS These applications include the classroom, TV listening, car riding, and one-on-one conversations. For severe to profound hearing loss, the PERSONAL FM System should be used in conjunction with a hearing aid. A Neckloop can be used with hearing aids that have a telecoil. An adaptor cord can be used with hearing aids that have direct audio input 15 16IN CASE OF DIFFICULTY If your Personal FM System is not working, check the following: 1. Read through the manual and user guide carefully to verify proper setup and installation of your system. 2. Make sure the batteries are fresh or completely charged and that the “plus” and “minus” termi- nals are installed correctly. 3. If the rechargeable batteries will only work for a short period of time (less than 1 hour) even after they are fully charged, they must be regenerated. Leave them in the receiver or transmitter with the unit turned on, for 5 - 6 hours. Then turn receiver or transmitter off, place it in the charger, and charge for 14 - 16 hours. This should restore normal battery life. Rechargeable bat- teries will gradually lose their capacity over time and should be replaced every year. 4. Make sure the microphone is plugged into the T32 Transmitter and the earphone is plugged into the Receiver. 5. If you have the PFM System 350, make sure the R31 Receiver’s plug mount microphone IS NOT plugged into the Transmitter. 6. If you’re using the PFM System 350 with the PFM R31 Receiver, make sure that the earphone has been plugged into the earphone jack and not into the R31 Receiver’s microphone jack. 7. Move the Transmitter and Receiver closer together. You may be out of range. When using the system indoors, it’s normal for the signal to momentarily disappear in certain locations. This is called a “drop-out.” Moving a few feet will restore the signal. 8. Make sure that the Transmitter and Receivers are tuned to the same channel. The units have stickers inside the back cover identifying the channel. Unless the Transmitter channel has been changed, set the Receiver to channel 1. 9. Do not try to use more than one Transmitter on the same channel in close proximity to each other. MORE THAN ONE TRANSMITTER ON THE SAME CHANNEL WILL RESULT IN INTERFERENCE IF THEY ARE CLOSE TOGETHER. Keep the systems 50 - 100 feet apart or use separate channels for each system used. 10. If you are still hearing interference on the Receivers, turn the Transmitter off and listen with a receiver. If you hear the interference with the Transmitter off, you need to change to a clear channel. See the re-tuning instructions. 11. If problems remain, contact your dealer for further help. Or call Williams Sound toll-free at 1-800-843-3544. Limited Warranty Williams Sound products are engineered, designed, and manufactured under carefully controlled condi- tions to provide you with many years of reliable service. Williams Sound warrants the Hearing Helper® Personal FM System against defects in materials and workmanship for FIVE (5) years. During the first five years from the purchase date, we will promptly repair or replace the Hearing Helper® Personal FM System. Microphones, earphones, headphones, batteries, chargers, cables, carry cases, and all other accessory products carry a 90-day warranty. WILLIAMS SOUND HAS NO CONTROL OVER THE CONDITIONS UNDER WHICH THIS PROD- UCT IS USED. WILLIAMS SOUND, THEREFORE, DISCLAIMS ALL WARRANTIES NOT SET FORTH ABOVE, BOTH EXPRESS AND IMPLIED, WITH RESPECT TO THE Hearing Helper® Personal FM System, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MER- CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. WILLIAMS SOUND SHALL NOT BE LIABLE TO ANY PERSON OR ENTITY FOR ANY MEDICAL EXPENSES OR ANY DIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY ANY USE, DEFECT, FAILURE OR MALFUNCTIONING OF THE PRODUCT, WHETHER A CLAIM FOR SUCH DAMAGES IS BASED UPON WARRANTY, CONTRACT, TORT OR OTHERWISE, THE SOLE REMEDY FOR ANY DEFECT, FAILURE OR MALFUNCTION OF THE PRODUCTS REPLACEMENT OF THE PROD- UCT. NO PERSON HAS ANY AUTHORITY TO BIND WILLIAMS SOUND TO ANY REPRESENTA- TION OR WARRANTY WITH RESPECT TO THE HEARING HELPER® PERSONAL FM SYSTEM. UNAUTHORIZED REPAIRS OR MODIFICATIONS WILL VOID THE WARRANTY. The exclusions and limitations set out above are not intended to, and should not be construed so as to con- travene mandatory provisions of applicable law. If any part or term of this Disclaimer of Warranty is held to be illegal, unenforceable, or in conflict with applicable law by a court of competent jurisdiction, the validity of the remaining portions of this Disclaimer of Warranty shall not be affected, and all rights and obligations shall be construed and enforced as if this Limited Warranty did not contain the particular part or term held to be invalid. If you experience difficulty with your system, call Toll-Free for customer Assistance: 1-800-843-3544 (U.S.A.) or +1 952 943 2252 (Outside the U.S.A.) If it is necessary to return the system for service, your Customer Service Representative will give you a Return Authorization Number (RA) and shipping instruction. Pack the system carefully and send it to: Williams Sound Corp. Attn: Repair Dept. 10321 West 70th Street Eden Prairie, MN 55344 USA Your warranty becomes effective the date you purchase your system. Your returned warranty card is our way of knowing when you warranty begins. Please take a moment to fill it out and mail the enclosed card. You may also register your product online: williamssound.com/registration.aspx. This information will help us serve you better in the future. Thank you! 17 18 TECHNICAL SPECIFICATIONS FM TRANSMITTER, MODEL PFM T32 Dimensions: 3-5/8" L x 2-3/8" W x 7/8" H (92.1 mm x 60.3 mm x 22.2 mm) Weight: 4.4 oz (125 g) with battery Color: Royal blue, shatter-resistant polypropylene Battery Type: Two (2) AA 1.5 V non-rechargeable Alkaline batteries (BAT 001), 70 mA nominal current drain, 30 hours approx. life (OR) Two (2) AA 1.5 V NiMH rechargeable batteries (BAT 026), 70 mA nominal current drain, 20 hours per charge approx., recharges in 14–16 hours, uses CHG 200 or CHG 1600 Charger Operating Freq’s: Selectable, 16 channels, 72.1 – 75.9 MHz*, internal rotary switch Stability: ± .005%, frequency synthesized, crystal reference, PLL Modulation: Wide-band FM, 75 kHz pk, 75 μS pre-emphasis RF Output: 8000 μV/m at 30 m, max., 40 mW typical Freq Response: 200 to 10 kHz, + 3 dB at 1% max. THD Signal-to-Noise Ratio: 55 - 60 dB, with R31 or R32 Receiver Microphone Gain Control: 45 dB maximum, 18 dB minimum range Transmit Antenna: Integral with 39" microphone cord Microphone: Electret type, 39" cord, 3.5 mm mono phone plug Controls: On/Off switch, slide-type; Microphone Mute Switch, slide-type; Compression Selector 1:1 or 2:1 with internal selectable jumper Mic Connector: 3.5 mm mono phone jack Compatible Receivers: PPA R35, PFM R31, PFM R32 Approvals: FCC, Industry Canada, RoHS, WEEE Warranty: 5 years, parts and labor (90 days on accessories) Note: FCC regulations, section 15.21, requires the user to comply with the rules of transmitter operation. Any changes or modifications made by the user not expressly approved for compliance may result in the loss of all privileges and authority to operate the equipment. RECEIVER, MODELS PFM R31 & PFM R32 Dimensions and 3-5/8" L x 2-3/8" W x 7/8" H (92.1 mm x 60.3 mm x 22.2 mm) Weight: 4.6 oz (130 g) with batteries Color: Royal blue, shatter-resistant polypropylene Battery Type: Two (2) AA 1.5 V non-rechargeable Alkaline batteries (BAT 001), 14 mA nom. current drain, 80 hours approx. life (OR) Two (2) AA 1.5 V NiMH rechargeable batteries (BAT 026), 14 mA nominal current drain, 50 hours per charge approx., recharges in 14–16 hours, uses CHG 200 Charger Operating Freq’s: Pre-Tuned, Field–tuneable, 72 MHz - 76 MHz*. Pre-set channels are E (72.9 MHz) and G (75.7 MHz) FM Deviation: Wide-band, 75 kHz, 75 μS de-emphasis AFC Range: ± 120 kHz Sensitivity: 4 μV at 12 dB Sinad with squelch defeated, squelches at 10 μV for min. 50 dB S/N ratio Freq Response: 100 to 10 kHz, + 3 dB Signal–Noise Ratio: 50 dB at 10 uV Receive Antenna: Integral with earphone cord Audio Output: 35 mW, max. at 16 Ω Output Connector: 3.5 mm mono phone jack Squelch: Set to turn off audio under weak or no signal condition Carrier Detect Ind: Red LED, turns on in the presence of a carrier Controls: Volume: rotary/on/off/volume Tone: 3-way slide switch; Lo = flat response (20 Hz), Mid = –3 dB at 235 Hz, Hi = –3 dB at 730 Hz Channel: 2-way slide switch; Ch 1 = 72.9 MHz, Ch 2 = 75.7 MHz Indicators: On/off and FM Note: Specifications are electrical performance Approvals: FCC, WEEE Warranty: 5 years, parts and labor (90 days on accessories) PFM R31 Receiver Only Mic Connector: 3.5 mm mono phone jack, supplies positive DC for Williams Sound electret mics Microphone: Plug mount electret, omnidirectional, with windscreen, 3.5mm mono phone plug (MIC 014) Mic Volume: Rotary control *DISCLAIMER: FCC RULES LIMIT USE OF THIS EQUIPMENT TO “AUDITORY ASSISTANCE FOR THE HANDICAPPED.” NOTE: SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.

ACOUSTIC SPECIFICATIONS Environmental Mic Response (PFM R31 Only) Input: 80 dB random noise Device: KEMAR mannequin with BTK 3550 Tester Y: 80.0 dB 80 db Main Y: 50.2 dB X: 100 Hz + 8 OCT LOG Main X: 4 kHz ANSI 2.44 TEST FM Response (PFM R31, R32) Input: 80 dB random noise Device: KEMAR mannequin with BTK 3550 Tester Y: 80.0 dB 80 db Main Y: 34.1 dB X: 100 Hz + 8 OCT LOG Main X: 4 kHz ANSI S3.22–1987 TEST 3.4 % at 800 Hz 2.2 % at 1600 Hz MAXIMUM LOW CUT (TONE SET TO HI) Max. SSPL90: 133.5 dB at 1000 Hz HF Avg SSPL90: 127.0 dB HF Avg Full On Gain: 35.4 dB at 60 dB in Reference Test Gain: 35.8 dB Response Limit: 78.01 dB F1=200 Hz, F2=8 kHz Total Harmonic Dist: 1.1 % at 500 Hz 2.7 % at 800 Hz 2.1 % at 1600 Hz

FM Response (PFM R31, R32) MINIMUM LOW CUT (TONE SET TO LOW) Max. SSPL90: 135.8 dB at 500 Hz HF Avg SSPL90: 127.1 dB HF Avg Full On Gain: 37.7 dB at 60 dB in Reference Test Gain: 38.1 dB Response Limit: 80.1 dB F1=200 Hz, F2=8 kHz Total Harmonic Dist: 3.6 % at 500 Hz 3.9 % at 800 Hz 2.2 % at 1600 Hz MEDIUM LOW CUT (TONE SET TO MID) Max. SSPL90: 135.5 dB at 600 Hz HF Avg SSPL90: 127.1 dB HF Avg Full On Gain: 36.8 dB at 60 dB in Reference Test Gain: 37.3 dB Response Limit: 79.4 dB F1=200 Hz, F2=8 kHz Total Harmonic Dist: 3.4 % at 500 Hz Environmental Mic Response (PFM R31 Only) NO TONE MODIFICATION Max. SSPL90: 134.8 dB at 500 Hz HF Avg SSPL90: 126.4 dB HF Avg Full On Gain: 40.9 dB at 60 dB in Reference Test Gain: 40.8 dB Response Limit: 81.1 dB F1=200 Hz, F2=8 kHz Total Harmonic Dist: 1.1 % at 500 Hz 1.1 % at 800 Hz 0.3 % at 1600 Hz 19 © 2007, Williams Sound Corp. MAN 072I


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply