WHYNTER PROTECH CDM-710BW (01) PDF Document

To prevent death or injury to the user or other people and property damage, the following instructions must be followed:

Read all instructions before using the refrigerator.

Never clean refrigerator parts with flammable fluids. The fumes can create a fire hazard. Do not use an excessively wet cloth, industrial solvents, and oil-based products to clean this refrigerator.

Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of this or any other refrigerator. The fumes can create a fire hazard.

Do not abuse, sit on, or stand on the refrigerator.

This refrigerator is not intended for use by persons (including children with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge) unless they have been given supervision or instruction concerning use of the refrigerator by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the refrigerator.

If the power cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

Use the refrigerator only for its intended function.

To avoid the risk of shock, the product should never be used in bathrooms, shower rooms, or in any other steamy or wet areas.

During installation, the power supply must not be excessively or dangerously bent or flattened.

Do not tamper with controls.

Make sure the power plug is placed fully and firmly into the wall socket. If the wall receptacle you intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker, have a qualified electrician install an outlet that is appropriate to local electrical codes and requirements.

Do not use multiple sockets or an extension cord as it may overheat and become a risk of fire.

Make sure the power plug is clean before usage.

After turning the refrigerator off, please take the power plug out of the socket.

Make sure hands are dry when connecting the power plug. The refrigerator is equipped with a three-prong grounded power plug on the power cord for your protection. Never modify, remove, or attempt to repair the power plug yourself.

Do not repair, disassemble, and/or modify the refrigerator by yourself.

Remove the exterior and interior packing.

Before connecting the refrigerator to the power source, let it stand upright for approximately 4 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation.

Clean the interior surface with lukewarm water using a soft cloth.

The refrigerator is designed for freestanding installation.

Do not store or install the refrigerator outdoors.

Place your refrigerator on a hard and level floor that is strong enough to support it when it is fully loaded.

To level your refrigerator, adjust the leveling legs at the bottom of the refrigerator if needed.

Allowance of at least 5 inches (127mm) of space between the back and sides of the refrigerator is suggested, which allows proper air circulation to cool the compressor and condenser.

We do not recommend installing the refrigerator on carpet.

Avoid installing the refrigerator near an oven or other heating source, as direct sunlight and heat sources may affect performance.

Ensure the refrigerator is installed in an area protected from the elements, such as wind, rain, water spray, or drips.

When using this refrigerator in confined spaces, such as a pantry, be sure to allow proper ventilation to prevent overheating and fire.

This refrigerator requires a standard 115/120 Volt AC ~/60Hz electrical ground outlet with a three-prong plug.

Ensure that the wall outlet and circuit are properly grounded by a qualified electrician.

Secure the cord behind the refrigerator to prevent accidental injury.

Always plug the refrigerator into its own individual electrical outlet matching the voltage rating on the refrigerator label to prevent overloading circuits.

Avoid pulling the power cord to unplug the refrigerator; grip the plug firmly and pull straight out from the receptacle.

Immediately repair or replace frayed or damaged power cords to prevent electrical hazards.

Due to potential safety hazards, it is strongly recommended not to use an extension cord with this refrigerator. However, if necessary:

Use only a UL/CUL-Listed, 3-wire grounding type refrigerator extension cord with a grounding type plug and outlet.

Ensure that the electrical rating of the extension cord is 115 volts and at least 10 amperes.

The temperature in the refrigerator is regulated by the thermostat control knob, which is located inside the refrigerator cabinet.

To adjust the temperature, simply turn the thermostat control knob clockwise or counterclockwise.

The markings “1 – 7” and “OFF” on the control knob indicate the different temperature settings, with “1” representing cold and “7” the coldest (32°F-50°F).

Setting 1: Use when a colder temperature is not required.

Setting 4: Normal setting suitable for daily use.

Setting 5-6: Use when a colder temperature is desired.

Setting 7: Use when the refrigerator needs to operate at its coldest temperature.

Note that even when set to “1”, the temperature will not exceed freezing.

Ensuring that the refrigerator is properly leveled is essential for its optimal operation. You can adjust the level by rotating each of the legs located at the bottom of the machine.

1. Place a carpenter’s level on top of the product to check if the refrigerator is level from front to back and side to side.

2. Turn the leveling legs to the right to lower that side of the refrigerator, and turn them to the left to raise that side of the refrigerator.

Under typical ambient conditions, the refrigerator usually doesn’t require defrosting. However, in colder ambient temperatures and/or high humidity, some frost may accumulate.

To defrost the refrigerator, simply set the thermostat dial to “OFF”, and defrosting should occur within a few hours.

Once defrosting is complete, return the thermostat control knob to the desired setting.

For faster defrosting, you can remove all items from inside the cabinet, unplug the refrigerator, and leave the door open.

Never use a knife or any other metal instrument to scrape ice or frost.

Your new refrigerator may produce sounds that are unfamiliar to you. Hard surfaces, like the floor and walls, can amplify these sounds. Here are common sounds you may hear and their possible causes:

Rattling Noises: These noises may originate from the flow of refrigerant or the water line. Items stored on top of the refrigerator can also contribute to rattling sounds.

Compressor Sounds: The high-efficiency compressor may emit pulsating or high-pitched sounds during operation.

Water Flow: Water running from the evaporator to the water reservoir may result in a splashing sound.

Refrigerant Circulation: At the end of each cycle, you may hear a gurgling sound caused by refrigerant flowing in the refrigerator.

Condenser Fan: You may notice the sound of air being forced over the condenser by the condenser fan.

If the refrigerator is unplugged, encounters a power interruption, or is turned off, you must wait 3-5 minutes before restarting the refrigerator. If you attempt to restart before this time delay, the refrigerator may not start.

Most power failures are resolved within a few hours and should not significantly affect the temperature of your refrigerator if you minimize opening the refrigerator cover.

If the power outage is expected to last longer, take the necessary steps to disconnect your refrigerator to prevent potential hazards.

When loading the cabinet, you can arrange the items in a single row or stack them. It is advisable to distribute the load throughout the refrigerator if you don’t have enough items to fill it completely, to avoid imbalanced loads.

Remove or relocate the adjustable shelves to accommodate larger cans, bottles, or other products.

Maintain small gaps between the walls and the items stored and avoid overloading the cabinet to facilitate air circulation.

Ensure the internal cabinet fan (located on the back wall panel) is not obstructed by items stored inside.

Do not attempt to slide the shelves outwards beyond their fixed positions to prevent items from falling.

Do not pull out more than one loaded shelf at a time, as this may cause the refrigerator to tilt forward if not properly installed.

Turn off the power, unplug the refrigerator, and remove all items including shelves.

Wipe the interior with a warm water and baking soda solution. The solution should consist of about 2 tablespoons of baking soda to one quart of water.

Clean the shelves with a mild detergent solution.

Wipe the exterior cabinet with warm water and mild liquid detergent.

Avoid using steel wool or steel brushes on the stainless steel surface, as these may cause erosion and rusting.

If the refrigerator will not be used for an extended period or is to be moved to another location, it’s necessary to defrost the unit and dry the interior.

1. Disconnect the refrigerator from the power supply by unplugging the power plug from the wall socket. Do not touch the power plug with wet hands.

2. Leave the door open to facilitate air circulation and prevent mold, mildew, and unpleasant odors.

Store the unit out of reach of children.

Remove all items from inside the refrigerator.

Securely tape down all loose items (such as shelves) inside your refrigerator.

Turn the adjustable legs up to the base to avoid damage.

Tape the door shut.

Ensure the refrigerator remains secure in the upright position during transportation and protect the exterior with a blanket or similar item.

Check if there is a power failure.

Ensure the refrigerator is plugged in and the power outlet has power.

Check if a house fuse has blown or the circuit breaker is tripped; replace the broken fuse or reset the breaker.

Adjust the temperature.

Keep the refrigerator away from sunshine or other heat sources.

Close the door tightly and do not open the door too frequently or for a long period of time.

Ensure the door gasket is not loose.

Ensure the item is in an area with temperatures above 60°F (16°C) and below 90°F (32°C).

Ensure no items are placed against the back internal cabinet wall.

Check if items are blocking the internal fan(s).

The ambient (room) temperature may be too low or high; decrease or increase the ambient temperature.

A large amount of contents may have been added to the refrigerator; do not add a large amount of contents at once to minimize temperature fluctuation.

The door may be opened too often or not closed completely.

The door gasket may not be sealing properly.

Note: It is normal for the fan to come on and off to circulate the air inside of the unit for even temperature distribution and to save energy.

The noise may come from the flow of the refrigerant and expansion of the inside walls, causing popping and crackling noises.

The high-efficiency compressor may make a pulsating or high-pitched sound.

Make sure the unit is on a hard and level surface.

Do not place the refrigerator on carpet.

Ensure the refrigerator is level.

Ambient temperature or humidity is high; lower the room humidity by a dehumidifier or air conditioner.

The door gasket is not sealing; ensure the door gasket is not loose or damaged.

Close the door tightly and do not open the door too frequently or for a long period of time.

The door gasket may not be sealing; ensure the door gasket is not loose.

If the door is not closing completely, use a screwdriver to loosen the screws to re-position the door/hinge and tighten the screws.

If ambient temperature or humidity is high, lower the room humidity with a dehumidifier or air conditioner.