Free English WHELEN CCP (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD WHELEN CCP (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What is the function of the WHELEN CCP Control Point Module?
The WeCanX (WCX) Control Point Module serves as the main controller of the Whelen WCX Series lightbar. When utilizing the Whelen Command Programming Software, this module can be configured via the USB-C port to provide the necessary instructions that allow the WCX lightbar to function and operate in the desired manner.
What is the Diagnostic Output on the WHELEN CCP?
The Diagnostic Output (J1, Pin 2) is a high-side programmable output signal, capable of syncing a maximum of 2.5 AMPS.
How does the Ignition Sense input on the WHELEN CCP work?
The Ignition Sense Input (J2, Pin 1) is to be wired to an ignition signal line on the vehicle. This will enable the WCX Control Point Module to turn on (line high, ignition sensed), or turn off (line low, ignition off). It must be connected to an ignition controlled circuit that can accommodate an additional 250 mA load.
How do the Digital Inputs on the WHELEN CCP function?
The Digital Inputs (J2, Pins 2-8 / Pins 10-17) are used as programmable digital inputs, activated by applying +VBAT to the input pin. These inputs can be used to trigger instructions for lightbar operation.
What is the purpose of the Analog Inputs on the WHELEN CCP?
The Analog Inputs (J2, Pins 9 / 18) are used as programmable analog inputs, capable of registering a range of voltages that can trigger lightbar operations when responding to voltage trip points set by the Whelen Command Programming Software.
What is the wiring configuration for the J1 connector on the WHELEN CCP?
| Pin | Wire Color | Function |
|---|---|---|
| 1 | RED | 10-30 VDC Power |
| 2 | RED/WHT | Diagnostic Output |
| 3 | BLACK | Ground |
| 4 | GREEN | Can – H |
| 5 | BLK/WHT | SHIELD |
| 6 | GREY | CAN – L |
A 5 AMP fuse is required on the RED wire connected to the positive terminal of the battery.
What is the wiring configuration for the J2 connector on the WHELEN CCP?
| Pin | Wire Color | Function |
|---|---|---|
| 1 | GRN | Ignition * |
| 2 | GRN/WHT | Input 2 (Digital) |
| 3 | GRN/BLK | Input 3 (Digital) |
| 4 | WHT/RED | Input 4 (Digital) |
| 5 | WHT | Input 5 (Digital) |
| 6 | YEL | Input 6 (Digital) |
| 7 | WHT/VIO | Input 7 (Digital) |
| 8 | WHT/GRN | Input 8 (Digital) |
| 9 | WHT/ORG | Input 9 (Analog) |
| 10 | BLU | Input 10 (Digital) |
| 11 | BLU/WHT | Input 11 (Digital) |
| 12 | BLU/BLK | Input 12 (Digital) |
| 13 | WHT/BRN | Input 13 (Digital) |
| 14 | WHT/BLK | Input 14 (Digital) |
| 15 | WHT/BLU | Input 15 (Digital) |
| 16 | RED/WHT | Input 16 (Digital) |
| 17 | WHT/YEL | Input 17 (Digital) |
| 18 | VIO | Input 18 (Analog) |
* Connect to an ignition controlled circuit that can accommodate an additional 250 mA load.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
CLICK HERE TO DOWNLOAD WHELEN CCP (01) PDF DOCUMENT