WATERSTONE 6100-18 (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD WATERSTONE 6100-18 (01) PDF MANUAL


PDF Content Summary: TRADITIONAL BRIDGE FAUCET INSTALLATION INSTRUCTIONS Model #s: 6100-12 6100-18

6150-12 6150-18 6200 6250 6300 6350 6100-12 6100-18 6200 6300 6150-12 6150-18 6250 6350 7600-12 7600-18

INSTALLATION GUIDE BEFORE YOU BEGIN YOUR INSTALLATION: 1 2 3 4

Turn o water supply. Observe all local plumbing codes. Inspect waste and water supplies for signs of damage. Replace as necessary. DO NOT use petroleum based products on this faucet.

REQUIRED TOOLS: PARTS INCLUDED: HK-BHC HANDLE BUTTON KIT (TRADITIONAL ONLY)

1. Adjustable Wrench 2. Phillips Screwdriver FAUCET HOLE PLACEMENT HK-USM1250 UNDER SINK MOUNTING HARDWARE KIT (1-1/4”)

1. NOT TO SCALE Recommended deck hole 1-3/8”. Drill holes for bridge faucet in mounting surface 8” on center. OPTIONAL SIDE SPRAY: We recommend installing the side spray hole a minimum of 4-3/4” away from nearest mounting hole of faucet. 8” 4” 4” RECOMMENDED HOLE SIZE 1-3/8” SINK OR MOUNTING SURFACE FAUCET INSTALLATION 1. 2. C C COUNTER OR SINK

B A BD D E A

Remove clamp nut (A) and washer (B) from threaded shroud (C). Fit flexible hoses (D) and rigid sidespray tube (E) through holes on counter or sink. (No plumbers putty is required. O-rings seals base). 3. 4. F F Slide washer and thread the clamp nut onto threaded shroud. Tighten nut snug to underside of sink or counter. Securely tighten clamp screws (F). CONNECTING SUPPLY HOSES A 1. Before connecting supply hoses, flush supply stops to clear any debris. Place a bucket underneath stops and run water for 5 to 10 seconds. Turn water off. 2. Carefully position hot and cold supplies so they will not interfere with other hoses. B 3. Connect supply hoses (A) to supply stops (B). DO NOT use teflon tape or plumbers putty. Turn water back on and check for leaks. OPTIONAL DECORATIVE BUTTONS 1. Place a small standard screwdriver in slot at bottom of metal ring that surrounds

handle buttons. Gently pry button from faucet handle. 2. Position new button and snap in with thumb. COMPASS HOT AND COLD FINISH MATCH CROSS HANDLE LEVER HANDLE LEVER HANDLE

CONNECTING OPTIONAL SIDE SPRAY 1. 2. 3. 4. A G COUNTER OR SINK

C BD F E

1. Insert side spray base (A) into side spray hole on your sink or counter. No plumbers putty is required. O-ring seals base. Slide washer (B), thread attaching nut (C) and securely tighten. 2. Slide sidespray hose (D) through side spray base. 3. Remove hose cap (E) from end of sidespray hose tube (F) on faucet (G). 4. Connect and tighten end of sidespray hose to sidespray hose tube. Check for leaks.

CLEANING AERATOR AND DEBRIS SCREEN 1. 2. 3. 4. 5.B C A

Depending on quality of your household water, the aerator and debris screen may become clogged. We recommend cleaning one week after installation, then a minimum of once of year thereafter. To remove the debris, follow the steps below. 1. Gently unscrew and remove spout tip (A) by hand. 2. Remove O-ring (B). To remove aerator (C), push with finger from bottom. 3. Thoroughly rinse aerator with water until all debris is removed. 4. Place aerator, then O-ring back into spout tip. 5. Gently screw spout tip, by hand, snuggly back onto spout.

CARE AND CLEANING FOR WATERSTONE FAUCET FINISHES ATTENTION: Waterstone offers many finishes for it’s products. Every finish is unique and requires different techniques for care and cleaning. Find your product’s finish in the sections below, then carefully read and follow directions for that finish.

CLEAR PROTECTIVE COATED FINISHES LIVING FINISHES

ABOUT YOUR FINISH: These finishes have a clear protective coating on them. Even though they have a protective coating, they are only con sidered semi-durable. If the outside clear coating is scratched or damaged in any way, the base metal finishes exposed will oxidize. Any use of an abrasive cleanser, or any abrasive pad, cloth or sponge can remove or dull the protective coating and Antique Brass - AB Antique Copper - AC American Bronze - AMB Antique Pewter - AP Distressed Antique Brass - DAB Distressed Antique Copper - DAC Distressed American Bronze - DAMB Distressed Antique Pewter - DAP Polished Brass - PB ABOUT YOUR FINISH: These finishes are considered Living Finishes and have NO PROTECTIVE COATING on them. Living finishes are finishes that have a very shallow patina on their surface. Es sentially, the finish is what nature would do to the surface over a long period of time. The finishes are intended to change with time and generally darken slightly where they are not being touched, and highlight where Antique Bronze - ABZ Black-Oil Rubbed Bronze - ORB Caribbean Bronze - CB Tuscan Brass - TB Unlacquered Polished Brass - UPB Weathered Brass - WB Weathered Copper - WC

damage the finish. Some available sink cleaners with bleach, soaps, and hand lotions will damage the finish, as can acidic organic cleansers. Always wipe your fixture down with a clean soft cloth and keep it clean and dry after use. IMPORTANT NOTICE: Polished Copper - PC Satin Brass - SB Satin Nickel - SN Venetian Bronze - VB the high use points are on the fixture. Hand oils, soaps, and acidic fluids and cleaners can damage the finish. These finishes are not durable, and are easily scratched or scuffed. Any type of astringent cleaner or any type of abrasive cleanser, pad, cloth or sponge will damage the finish. To help keep the surface on the fixture from oxidizing in the packaging, Waterstone initially applies a wax to the finish surface to help protect and prevent the finish from exposure to air and oxidizing prior to installation. IMPORTANT NOTICE:

It is the responsibility of the customer to check for any material finish defects BEFORE installation. Waterstone does not warranty these finishes AFTER installation. SUGGESTED FINISH MAINTENANCE PROCEDURE: 1. Do not allow water spots to dry on the fixture. Keep the surface clean and dry after use. 2. Periodic cleaning can be done by using a mild diluted glass cleaner (we recommend Windex). Apply the mild cleaner to a soft clean cloth, and periodically wipe your fixture down to remove water spots and surface debris. 3. Never use cleaners with bleach, abrasives, or vinegar. Never use any type of abrasive pad or sponge. POWDER COATED FINISHES ABOUT YOUR FINISH: It is the responsibility of the customer to check for any material finish defects BEFORE installation. Waterstone does not warranty these finishes AFTER the fixture has been installed. SUGGESTED FINISH MAINTENANCE PROCEDURE FOR ANTIQUE BRONZE, CARIBBEAN BRONZE, TUSCAN BRONZE, UNLACQUERED POLISHED BRASS AND WEATHERED BRASS: 1. Do not allow water spots to dry on the fixture. Keep the surface clean and dry after use. 2. Periodic cleaning can be done by using a micro-crystalline wax (we recommend Renais sance Wax). Apply the wax with a soft non-abrasive tissue paper, and gently buff the wax with a soft clean cloth to help remove surface spots and add a protective coating to the finish. 3. Never use cleaners with bleach, abrasives, or vinegar. Never use any type of abrasive pad or sponge. SUGGESTED FINISH MAINTENANCE PROCEDURE FOR BLACK-OIL RUBBED BRONZE:

These finishes are powder coated color finishes. They have NO ADDITIONAL PROTECTIVE COATING. These finishes are not considered durable finishes and can be scratched, chipped or scuffed. If the exterior color coating is damaged, the exposed metal base will oxidize. Any use of an abrasive cleanser, or any abrasive pad, cloth or sponge can remove or dull the color coating and damage the finish. Some available sink cleaners with bleach, soaps, and hand lotions will damage the finish, as can Almond - 01 Black - 06 Biscuit - 07 Chocolate Bronze - CHB Euro-White - EW Matte Black - MB White - WT 1. Do not allow water spots to dry on the fixture. Keep the surface clean and dry after use. 2. Periodic cleaning can be done by applying mineral oil to a clean soft cloth and gently wiping down the finish surface to clean. Make sure not to rub too hard, in that you can remove too much of the surface patina surface with aggressive cleaning. 3. Once the mineral oil has been applied, with a clean soft dry cloth gently pat the finish surface to remove any excess oil on the fixture to until the fixture no longer looks “wet”. 4. Never use cleaners with bleach, abrasives, or vinegar. Never use any type of abrasive pad or sponge.

acidic organic cleansers. Always wipe your fixture down with a clean soft cloth and keep it clean and dry after use. IMPORTANT NOTICE: It is the responsibility of the customer to check for any material finish defects BEFORE installation. Waterstone does not warranty these finishes AFTER installation. SUGGESTED FINISH MAINTENANCE PROCEDURE: 1. Do not allow water spots to dry on the fixture. Keep the surface clean and dry after use. 2. Periodic cleaning can be done by using a mild diluted glass cleaner (we recommend Windex). Apply the mild cleaner to a soft clean cloth, and periodically wipe your fixture down to remove water spots and surface debris. 3. Never use cleaners with bleach, abrasives, or vinegar. Never use any type of abrasive pad or sponge. SUGGESTED FINISH MAINTENANCE PROCEDURE FOR WEATHERED COPPER: 1. Do not allow water spots to dry on the fixture. Keep the surface clean and dry after use. 2. Periodic cleaning can be done by applying denatured isopropyl alcohol to a clean soft cloth and gently wiping down the finish surface to clean. Do not rub too hard, in that you can remove too much of the surface patina. This step will leave the finish looking a shade darker. 3. Using a different soft clean cloth, apply a non-abrasive metal polish (we recommend “Miracle Shine” by GSM) to the cloth and gently rub the polish into the finish. This will clean, protect, and brighten up the finish after it was left darker from the alcohol cleaning in step 2. 4. Never use cleaners with bleach, abrasives, or vinegar. Never use any type of abrasive pad or sponge.

CONTINUED ON NEXT PAGE... CARE AND CLEANING FOR WATERSTONE FAUCET FINISHES (Cont.)

PLATED FINISHES ABOUT YOUR FINISH: These finishes are the most durable finishes Waterstone offers. The best general maintenance is regular cleaning. Even though these finishes are considered durable, you Black Nickel - BLN Chrome - CH Polished Nickel - PN STAINLESS STEEL ABOUT YOUR FINISH: Waterstone’s stainless steel fixtures are actually made of solid stainless. This finish has NO PROTECTIVE COATING on it. Stainless steel is by its material nature very tarnish Stainless Steel - SS

can never use any abrasive type cleaners, clothes, or pads to clean your fixture. Always try and keep your finishes clean and dry. Trapped moisture on the surface of your Satin Chrome - SC resistant, but by no means tarnish or stain proof. This finish will indeed oxidize naturally over time and react to its environment, and in a reaction to some chemical cleaners that have bleach in them rusting can be induced on the finish. Keep your stainless fixture wiped

finish can lead to staining. Astringent cleaners, chlorine, bleach, along with acidic based organic cleansers are potentially harmful to these finishes. Chrome plated finishes are very tarnish resistant. However, they are not indestructible and can scratch and mar. IMPORTANT NOTICE: It is the responsibility of the customer to check for any material finish defects BEFORE installation. Waterstone does not warranty these finishes AFTER the fixture has been installed. SUGGESTED FINISH MAINTENANCE PROCEDURE: 1. Do not allow water spots to dry on the fixture. Keep the surface clean and dry after use. 2. Periodic cleaning can be done by applying denatured isopropyl alcohol with a soft clean cloth to gently remove surface spots. 3. Never use cleaners with bleach, abrasives, or vinegar. Never use any type of abrasive pad or sponge. PRECIOUS METALS clean and dry, and use only a cleaner specifically made for stainless steel. Trapped moisture on the surface of your finish can lead to staining. Astringent cleaners, chlorine, bleach, along with acidic based organic cleansers are potentially harmful to stainless steel finishes. IMPORTANT NOTICE: It is the responsibility of the customer to check for any material finish defects BEFORE installation. Waterstone does not warranty these finishes AFTER the fixture has been installed. SUGGESTED FINISH MAINTENANCE PROCEDURE: 1. Do not allow water spots to dry on the fixture. Keep the surface clean and dry after use. 2. Periodic cleaning can be done by applying a “stainless steel cleaner” with a soft clean cloth to gently remove surface spots and brighten the finish. 3. Never use cleaners with bleach, abrasives, or vinegar. Never use any type of abrasive pad or sponge.

ABOUT YOUR FINISH: This finish is done with real precious metal gold plating on the brass fixture surface. This finish has NO PROTEC TIVE COATING and is extremely soft. Some or all of the Gold plating will be removed if any type of polish is used. Polished Gold - PG Satin Gold - SG

Additionally, the finish will wear aware with time. The gold plating is considered very delicate and can be easily scratched or scuffed. Any type of astringent cleaner or any type of abrasive cleanser, pad, cloth or sponge will damage the finish. IMPORTANT NOTICE: It is the responsibility of the customer to check for any material finish defects BEFORE installation. Waterstone does not warranty these finishes AFTER the fixture has been installed. SUGGESTED FINISH MAINTENANCE PROCEDURE: 1. Do not allow water spots to dry on the fixture. Keep the surface clean and dry after use. 2. Periodic cleaning can be done with mild liquid soap only. Wipe gently with a soft cloth to clean. 3. Never use cleaners with bleach, abrasives, or vinegar. Never use any type of abrasive pad or sponge. 41180 Raintree Court • Murrieta, CA 92562 1-888-304-0660 • 951-304-0520 waterstoneco.com VEN-038-BRGF Rev. B


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply