WAC LIGHTING FM-4115 (01) PDF MANUAL


Post questions, comments, reviews or errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD WAC LIGHTING FM-4115 (01) PDF MANUAL


PDF Content Summary: INSTALLATION INSTRUCTION Slice - LED Flush Mount FM-4115 WARNING IMPORTANT: NEVER attempt any work without shutting off the electricity. - Read all instructions before installing. - System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. - Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF” the circuit breaker switch(es) that control the power to the fixture or room that you are working on. - Place the wall switch in the “OFF” position. CAUTION - All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this fixture. CAUTION When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only. AVERTISSEMENT IMPORTANT : Coupez l’électricité avant TOUTE manipulation. - Lisez toutes les instructions avant d’installer. - Système est destiné à être installé par un électricien qualifié en conformité avec le code national de l’électricité et les règlements locaux. - Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt (« OFF »). - Placez l’interrupteur mural en position d’arrêt (« OFF »). MISE EN GARDE - Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base. ADVERTENCIA IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico. - Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta lámpara. - Sistema está disenado para ser instalado por un electricista calificado, de acuerdo con el código eléctrico nacional y las normas locales. - Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación principal en la posición “OFF” (APAGADO). - Coloque el interruptor de la pared en la posición “OFF” (APAGADO). PRECAUCIÓN - Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calificación ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo. HARDWARE A1 B1 C1 D1

Wire Connector Qty: 3 pcs Junction Box Screw Qty: 2 pcs + 1 Extra Allen Screw Qty: 1 pcs Extra Allen Screw Qty: 1 pcs Extra Allen Wrench Qty: 1 pcs Allen Wrench Qty: 1 pcs Allen Wrench Qty: 1 pcs waclighting.com Phone (800) 526.2588 Fax (800) 526.2585 Headquarters/Eastern Distribution Center 44 Harbor Park Drive Port Washington, NY 11050 Central Distribution Center 1600 Distribution Ct Lithia Springs, GA 30122 Central Distribution Center 1600 Distribution Ct Lithia Springs, GA 30122 Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760 Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760 Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760

1 WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. INSTALLATION INSTRUCTION Slice - LED Flush Mount FM-4115 FIG.1 Junction Box Input Wires Wire Connector Mounting Plate Junction Box ScrewPressed Glass PREPARATION 1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar. 2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation. CONNECTING THE WIRES (Fig. 2) 3. Connect the fixture wires with supply wires as shown in Fig. 2, making sure all wire connector (A1) are secured. If your outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate using the green screw provided. After all wires are connected, tuck them carefully inside the junction box. MOUNTING THE FIXTURE (Fig. 1) 4. Secure mounting plate to the junction box using junction box screws (B1). The side of the mounting plate marked “GND” must face out. 5. Place the canopy over the mounting plate and secure with mounting screws. 6. Twist lock the glass into the canopy, then lock it with allen screw (C1) using allen wrench (D1). A1B1 Allen ScrewC1 D1 Allen Wrench Canopy Mounting Screw Fig.2 Wiring waclighting.com Phone (800) 526.2588 Fax (800) 526.2585 Headquarters/Eastern Distribution Center 44 Harbor Park Drive Port Washington, NY 11050 Central Distribution Center 1600 Distribution Ct Lithia Springs, GA 30122 Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760 2 WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Fixture Wires Black or Smooth Fixture Wires White or Ribbed Fixture Wires Bare wire (Ground) House Wires Black (Hot) House Wires White (Neutral) House Wires Green or Bare Copper (Ground)


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply