VITAMIX ASCENT X2 VM0231 (01) PDF Document

Carefully read all instructions before operating the VITAMIX ASCENT X2 VM0231 for the first time. Save these instructions for future reference.

NEVER attempt to remove the retainer nut or blade assembly from the container. The container is designed to be completely cleanable without removing the retainer nut and blade assembly. The cleaning and sanitizing procedures or a dishwasher cleaning cycle will ensure a complete and thorough cleaning of the container and components.

If the container is damaged, DO NOT USE IT. Contact Vitamix Household Technical Support IMMEDIATELY for assistance.

Wipe the motor base with a damp, soft cloth or sponge rinsed in a mild solution of liquid dish soap and warm water and dry with a soft cloth.

Wash and install the tamper holder.

Wash the container, lid, lid plug, and tamper with warm, soapy water. Rinse all parts and wipe dry with a dry, soft cloth.

Place the appliance on a counter that is level, dry, and clean.

Plug the appliance into a grounded, 3-prong outlet.

ALWAYS use grounded outlets.

NEVER remove the ground.

NEVER use an adapter.

NEVER use an extension cord.

NEVER plug the appliance into a timer or an outlet controlled by a switch.

Failure to follow instructions can cause death or electrical shock.

NEVER immerse the power cord, power plug, or motor base in water or any other liquid.

If the appliance becomes submerged, unplug immediately.

ALWAYS turn off AND unplug the appliance when not in use and before assembling, disassembling, moving, cleaning, and storing.

ALWAYS ensure the appliance is unplugged from the power outlet before cleaning the motor base or centering pad, or touching parts that move.

NEVER modify the plug in any way.

If the appliance will not operate, unplug the appliance and reset the household electrical system circuit protector.

If the circuit protector continues to trip, unplug the appliance from the outlet and contact a qualified electrician.

NEVER allow the power cord to hang over the edge of a table or counter, touch hot surfaces, or become knotted.

NEVER unplug the appliance by pulling on the cord. To unplug the appliance, grasp the power plug and pull from the outlet.

NEVER touch moving parts. Keep hands and utensils out of the container.

NEVER come in contact with moving parts, especially the blades.

The blending blade assembly is very sharp. Handle carefully and keep out of reach of children.

NEVER operate the appliance with loose, nicked, or damaged blending blades. Check the blending blades prior to each use and replace if damaged.

NEVER tighten the acorn nut (on the top of the blade assembly). If loose, replace the blade assembly immediately.

ALWAYS ensure the appliance is completely and properly assembled before operation including the unwinding of the power cord fully before use.

NEVER place a blade assembly on the motor base unless assembled to the Vitamix container to reduce the risk of injury.

NEVER attempt to place a container on an operating motor base or operate a motor base without a container properly in place.

ALWAYS operate the appliance with the lid and lid plug firmly in place when the machine is in operation. NEVER remove the 2-part lid while the blades are rotating. Only remove the lid plug to add ingredients and to use the tamper.

NEVER operate the appliance without ensuring the lid is securely locked in place.

NEVER operate the appliance without the centering pad installed properly underneath the container.

Ensure the container is flush with the centering pad to ensure the drive spline is engaged with the drive socket before operating.

High temperatures exist when blending hot liquids.

When blending hot liquids or ingredients in the container, use caution; spray or escaping steam may cause burns.

NEVER expose the container to temperatures or ingredients over 210°F (99°C).

To avoid possible burns, NEVER start on speeds above Variable Speed 1 when processing hot liquids in a large container. Escaping steam, splashes, or contents may burn. ALWAYS operate with the lid and lid plug in place and start on Variable Speed 1, then slowly increase to 10.

Extreme caution must be used when moving an appliance or container filled with hot oil or other hot liquids; spray or escaping steam may cause burns.

Turn the On/Off Switch on the lower right side of the motor base to the ON (I) position.

Load the container according to the Vitamix recipe directions or the Load Order Illustration.

Place the lid onto the container:

Push down on the lid until the two tabs snap onto the lip of the container.

Insert the lid plug and turn clockwise to lock it into the lid.

Place the container with lid onto the motor base.

Turn the dial clockwise to Variable Speed 1.

Press the Start/Stop Switch. The blades will begin to turn and the timer will count the minutes and seconds the blend has been processing.

Rotate the dial between Variable Speed 1 and 10 during the blending cycle to increase or decrease the speed of the blades.

At the end of the blend, rotate the dial counter-clockwise to Standby | or press the Start/Stop Switch ▷ to stop the appliance.

Turn the On/Off Switch on the lower right side of the motor base to the ON (I) position.

Load the container according to the Vitamix recipe directions or the Load Order Illustration.

Place the lid onto the container:

Push down on the lid until the two tabs snap onto the lip of the container.

Insert the lid plug and turn clockwise to lock it into the lid.

Place the container with lid onto the motor base.

Turn the Variable Speed Dial counter-clockwise to the desired program and the display will show the default program time.

Press the Start/Stop Switch to start the program. The appliance will stop automatically at the end of the program or press the Start/Stop Switch at any time to stop the program.

Remove the lid plug by turning it counter-clockwise, insert the tamper through the lid plug opening, and stir until the mixture ‘burps’.

If this does not work, press the On/Off Switch to stop the motor.

Remove the container from the motor base, remove the lid, and use a rubber spatula to press the air bubble away from the blades.

Add liquid if necessary.

Replace the lid and lid plug and return the container to the motor base and continue blending.

After blending, wait until the blades stop completely before removing the lid or removing the container from the motor base.

Use a Vitamix Under Blade Scraper or spatula to remove salsa, jelly, jam, peanut butter, and other ingredients from the container.

If food becomes lodged around the blending blade, remove the container from the motor base, and use a spatula to dislodge the food. NEVER use fingers as the blending blade is sharp.

If the blend is not processing when blending dry, thick, or heavy mixtures, stop operation and use a spatula to dislodge the food. NEVER use fingers as the blade is sharp. Allow the motor to cool for 1 minute before turning the appliance back on.

ONLY remove the lid plug to use the tamper or to add ingredients.

NEVER use the tamper for more than 30 consecutive seconds to avoid overheating.

The container should not be more than 2/3 full when the tamper is used.

Fill the container half full with warm water and add a couple of drops of dishwashing liquid.

Snap or push the complete 2-part lid into the locked position.

Rotate the knob counter-clockwise to the Self-Cleaning icon.

On the Ascent X2 model, the processing time will display for the Self-Cleaning program.

Press the Start/Stop Switch.

The program will stop automatically when complete.

Rinse and drain all pieces.

Fill the container half full with warm water and add a couple of drops of dishwashing liquid.

Snap or push the complete 2-part lid into the locked position.

Press the Start/Stop Switch to turn on the appliance and slowly increase to Variable Speed 10.

Run the appliance for 30 to 60 seconds.

Rotate the Variable Speed Dial to Standby | or to Variable Speed 1 and press the Start/Stop Switch to turn off the appliance.

Rinse and drain all pieces.

First perform the “Container Cleaning” instructions.

Then repeat the “Container Cleaning” instructions but add 1.5 teaspoons (7.4 ml) of liquid bleach to 16 oz. (473 ml) of water.

Allow the mixture to stand in the container for an additional 1-1/2 minutes.

Pour the bleach mixture out. Allow container to air dry. DO NOT rinse after sanitizing. If desired, rinse immediately before next use.

First perform the “Container Cleaning” instructions.

Then repeat the “Container Cleaning” instructions but use 16 oz. (473 ml) of vinegar for every 16 oz. (473 ml) of water.

Allow the mixture to stand in the container for an additional 3 full minutes. Total contact time of the vinegar solution in the container should equal 5 minutes.

Pour the vinegar solution out of the container over the inside surface of the 2-part lid.

Repeat the sanitizing procedure a second time (Steps 2 through 4).

Allow the container and lid to air dry. DO NOT rinse after sanitizing. If desired, rinse immediately before next use.

Turn off and unplug the appliance and remove the container from the motor base.

Wash the outside surface with a damp, soft cloth or sponge rinsed in a mild solution of liquid dish soap and warm water. NOTE: NEVER immerse the power cord, power plug, or motor base in water or any other liquid.

The centering pad can be removed for more thorough cleaning and is dishwasher safe or can be hand-washed in warm, soapy water.

Immediately dry all surfaces and polish with a soft cloth.

The tamper is dishwasher safe or can be hand-washed in warm, soapy water. Rinse clean under running water and then dry.

The motor is designed to protect itself from overheating.

If the appliance will not start immediately, check to ensure the appliance is plugged in and the On/Off Switch is ON.

If the motor has overheated, allow the motor to cool for 20-45 minutes.

If the motor is overheated, allow the motor to cool for 20-45 minutes.

ALWAYS load the container according to the Vitamix recipe directions or the Load Order Illustration.

The Load Order Illustration is as follows:

On/Off Switch 1: Controls power to the machine and is located on the lower right side of the motor base.

Display:

Container Detect – Shows three dashes (…) on the display if a compatible container is not properly positioned on the motor base. 0:00 will show on the display once a compatible SELF-DETECT container is in position. – 0 – will show on the display if there is no program available for the attached container.

Sleep Mode – Dims the display if the control panel is not used for 30 seconds. To exit sleep mode, rotate the Variable Speed Dial to the desired speed or program for the next blend.

Error Code – Shows numbers on the display indicating the appliance has experienced a fault. Document the error code number and contact Vitamix Household Technical Support for resolution.

Timer – Counts up when using variable speed until the Start/Stop Switch is pressed. Each container is programmed with a specific maximum run time. The blender will shut down automatically when the maximum run time has elapsed.

Motor Overheated – Flashes three dashes (…) on the display if the motor is overheated. Allow the motor to cool for 20-45 minutes.

Pulse – Rotates the blade at the speed selected on the Variable Speed Dial.

Start/Stop Switch ▷ – Starts or stops the blending at any time and is located on the right side of the control panel.

Variable Speed Dial – Contains all the modes the appliance operates:

Variable Speed – Provides manual speed control from Variable 1 (slowest) to 10 (highest).

Standby | – Pauses the appliance and has it ready to start the next recipe. Standby is located at the top position on the Variable Speed Dial.

Self-Cleaning – Runs the cleaning cycle after water and dishwashing liquid have been added to the machine and the lid and lid plug are in place.

Programs – Operates the appliance for preset times and will stop automatically at the end of the program. When the Start/Stop Switch is pressed in the middle of a program, the machine will stop and the program time will reset on the display to the beginning of the run time.