TWOTHOUSAND QS620 (01) PDF MANUAL

This machine is designed for high performance, adopting a group of high-speed circumvolving knives to repeatedly circulate and cut up food in the bowl. It can speedily cut up meat, fruit, vegetables, etc., and can also be used for filling preparation.

All parts that touch the food are made of high-quality aluminium or stainless steel, meeting national food sanitation standards.

The machine is set with a top cover safety protect device to avoid suddenness accidents. It also has an electromotor protection device that stops the power automatically during overload or under reverse circuits.

It is suitable for food preparation in hotels, family kitchens, restaurants, bars, canteens, etc.

Bowl diameter	Capability	Voltage	Frequency	Power	Rating input power	IPNO	Dimensions (mm)	Weight
600 mm	400 kg/h	220V	50 Hz	1.1 kW	1.4 kW	IPX1	775x710x940	126 kg

1. Check if the power supply voltage conforms with the data plate and ensure the floor line is fast and credible.

2. For power lines without a plug, connect to a device installed at the fixed placement with at least 3mm point distance. The rated current should be ≥ 35A.

3. Check if the knife is tight; if loose, lock the screw. Put down the bowl tray cover.

4. Test the machine: check if the bowl’s turning direction is the same as the label shows. If not, exchange any two fire lines of the 3-phase power line.

When adding food into the bowl, the food size must be moderated.

Meat needs to have bone and skin removed.

Put the meat piece by piece to let the knife work more effectively.

It can cut 8kg of meat or 5kg of vegetables at one time.

Attention: When the machine is working, hands must not loll in the danger area under the bowl tray cover.

Make sure to move out the food only after the power is shut down.

1. After finishing, clean all parts such as the bowl, knife, barrelhead, etc., to keep sanitation.

Attention: Do not clean the machine by water under belch (high pressure/direct spray).

2. The machine was pre-filled with high-quality lubricant in the decelerate box. Generally, it can be used for one year. When lubricant needs changing or adding, use 40# gear oil.

The machine has an electromotor protect device. It will stop the power automatically if it overloads or experiences under reverse circuits. To restart, shut down the power, clean out the obstruction, then restart the machine after connecting the power.

Trouble	Reason	Debar way
Press start key, machine can not work.	Touch not well with the power	Check the electric circuitry
Low working efficiency	Knife fray	Re-polish the knife mouth or change knife
	Drive belt skid	Adjust tight up belt wheel or change belt.
Big noise at gear-box, heat graveness.	Lubricate not good	Add or change lubricant

Symbol	Name	Q’ty
SB2	Start button	1 group
HL1	Indication light
SB1	Stop button
M	Motor	1
KM1	Contactor	1
FR1	Heat relay	1
SQ1	Limit switch	1

(The manufacturer has the right to change the circuit without notice)

Illus	Part No.	Name of part	QTY	Illus	Part No.	Name of part	QTY
1	QS620-08	Bowl	1	22	QS620-09	Clamp plate I	1
2	QS620-24	Pulley shield	1	23	GB5781-86	Bolt M8x80	3
3	QS620-31	Left cover	1	24	QS620-10	Cutter	6
4	QS620-07	Faceplate	1	25	QS620-09	Clamp plate II	6
5	QS620-01	Body	1	26	QS620-06	Supporter seat	1
6	QS620-02	Front cover	1	27	QS620-12	Main shaft	1
7	YCB20-4	Motor	1	28	QS620-28	Tension seat	1
8	QS620-21	Motor fixed plate	1	29	QS620-26	Tension pulley	1
9	QS620-33	Belt pulley	1	30	GB276-82	Bearing 6202-2Z	1
10	A700	Belt	2	31	QS620-27	Sleeve	1
11	3″	Foot wheel	4	32	GB276-82	Bearing 6202-2Z	1
12	A1100	Belt	2	33	QS620-11	Bowl cover	1
13	QS620-29	Big belt pulley	1	34	QS620-02	Back plate	1
14	HWH-25-08	Bearing seat	1	35	QS620-13	Left nut	1
15	GB276-82	Bearing 6206-2Z	3	36	GB7813-87	Bearing seat 1506	1
16	QS620-30	Connector shaft	1	37	QS620-25	Belt pulley	1
17	QS620-32	Connector sleeve	1	38	QS620-18	Switch shield	1
18	NP7030	Reductor	1	39	LX19-001	Limit switch	1
19	QS620-29	Big belt pulley	1	40	QS620-14	Axis	1
20	GB7813-87	Bearing seat 1506	1	41	QS620-15	Bowl cover seat	1
21	QS620-13	Right nut	1	42	M8	Handle sphere	2