TRUECAM A4 (01) PDF Document

a) Insert the micro SD card into the slot. Always turn off the TRUECAM A4 device whenever inserting or removing the SD card.

b) Install the device on the windshield.

c) Connect the USB port and the cigarette lighter socket with the car charger, then start the engine. The device will automatically power on and start recording.

1. Start the car engine.

2. The TRUECAM A4 device will turn on and start recording automatically.

3. Press the file protection button to lock or unlock the recording video file.

4. Press the down button to start or stop audio recording.

5. Press the Power button to turn off the LCD display.

6. Press the OK button to stop or start recording.

7. When you turn the car engine off, the device will save the file and will be automatically powered off.

In recording mode, press the camera button to take a photo in the current recording resolution.

In standby mode, press the camera button to take a photo in the menu setting resolution.

1. Press the menu button in the video mode to enter the settings options, then choose motion detection.

2. If the device detects a moving object, a red icon will start flashing slowly and the camera will start recording automatically.

When the device no longer detects any moving object, it will automatically stop recording.

Note: It is not recommended to use the motion detection and loop recordings together.

In case of an accident while the camera is recording, a key icon will be shown on the screen and the current video will be stored and protected against deletion caused by cycle recording.

1. While the device is recording, press the menu button. A key icon will be shown on the screen, and the device will lock and protect the current video from deletion.

2. Press the menu button again to disable the file protection function.

1. When the device is in standby status, press the mode button to enter playback mode.

2. Press the up/down button to choose a video file or image file.

3. Press the OK button to play or pause the video file.

4. Press the menu button to enter menu settings.

5. Press the mode button again to enter the menu settings.

1. Turn off the device and connect it via USB cable to a computer.

2. A menu will be shown on the screen. Choose the “Mass Storage” option and a “USB connected” message will be shown. A removable disc will appear on your computer.

3. Open the removable disc. The video and image files will be stored in the “DCIM” folder.

GPS coordinates view (optional): This allows you to display the GPS position within the video. The location is displayed in the form of coordinates.

Current speed view (optional): This allows you to display the current speed within the video, which is usable for future reference.

The video lock feature can be used to lock a video from being overwritten by another video in the future. You can lock videos either in the recording mode or in the playback mode.

The TRUECAM A4 automatically begins recording when it detects sufficient motion, for example, when reversing. The amount of motion needed to begin recording depends on the level of motion sensitivity selected. Be careful when selecting high sensitivity as this may quickly fill up the memory card.

Loop recording allows the TRUECAM A4 to continuously record regardless of the memory card capacity. You can choose from four time intervals: Off / 2 min / 3 min / 5 min. The selected interval determines how long the camera will record for and save a file. The advantage of this setup is that you will never run out of space on your memory card. Moreover, it is much easier to send small files, for example, as an E-mail for use as evidence.

This function is used to delay turning the camera on or off when the car engine is turned on or off. This can increase the free space on the memory card (when there is a switch on delay) or can provide a record of what happens when you leave your car (when there is a switch off delay).

Insert the GPS / Speed camera detector module into the camera holder. Install the device on the windshield with the sticker or the sucker holder.

When the device is powered, the speed camera detector speaker will provide voice instructions, and the device will automatically start to receive a GPS signal.

When connected to a GPS satellite, the GPS icon will be shown on the LCD display.

Note: The GPS module works properly only when it is plugged into the DVR mount adapter that is connected to power in the car lighter. When you want to change the voice alert setting, the GPS module must be connected to power in the car lighter as noted.

When in recording mode or standby mode, pressing the up button will switch the screen to show information about current speed, compass, and distance to a speed camera. If the driving speed is above the current speed limit, a speed limit icon will appear.

LED light	Status	Description
Rec light (blue)	Flash	Device is recording
	On	Device is in standby or playback mode
	Off	Device is off
Charging light (red)	On	Charging battery
	Off	Charging finished

Button	Function	Action	Remark
Power button	Power on/off	Long press	Turn on/off device
	LCD on/off	Short press	Turn on/off LCD display in recording and standby mode
Menu button	Menu setting	Short press	In standby mode, enter menu list
File protection button	File protection	Short press	In recording mode, lock/unlock the video file
Camera button	Take picture	Short press	Take a photo
Mode button	Switch mode	Short press	Switch video/playback mode
Up button	Up / Speedometer on / off	Short press	Up button in menu settings. In recording mode or standby mode, press to turn the speedometer on / off
OK button	Video record	Short press	Start/stop video recording
Down button	Down/mute	Short press	Down button in menu settings. Start/stop voice recording in recording mode

Button	Function	Action	Remark
Menu button	Menu setting	Short press	Enter menu list
Mode button	Switch mode	Short press	Switch video/playback mode
Up button	1) Previous file	Short press	Previous file
	2) Rewind	Short press	When playing video, press this button to rewind
OK button	Play/pause video file	Short press	Play/pause video file
Down button	1) Next file	Short press	Next file
	2) Fast forward	Short press	When playing video, press this button to fast forward play

Function	Menu item	Remark
Resolution	1080P 1920×1080 / 720P 1280×720 / WVGA 848×480 / VGA 640×280	Sets video resolution.
Loop recording	Off / 2 min / 3 min / 5 min	Sets the length of the video time loop.
Picture resolution	12M / 8M / 5M / 3M / 2MHD	Sets photo resolution.
Exposure	+2.0 ; +5/3 ; +4/3 ; +1.0 ; +2/3 ; +1/3 ; 0 ; -1/3 ; -2/3 ; -1.0 ; -4/3 ; -5/3 ; -2.0	The “+” increases recording brightness. The “-” decreases brightness and darkens the recording.
White balance	Auto / Daylight / Cloudy / Tungsten / Fluorescent	We recommend setting it to Auto. White Balance depends on light conditions.
WDR	Off / On	Sets Wide Dynamic Range.
Motion detection	Off / Low / Medium / High	Motion Detection function settings.
G-sensor	Off / Low / Medium / High	G-Sensor sensitivity settings.
Record audio	Off / On	Audio Recording settings.
Date stamp	Off / On	To set the time stamp on video.
Driver name stamp	– – – – – –	Sets the driver’s name.
Driver label	Off / On	Sets the display of the driver’s name.
Image rotation	Off / On	Rotates the image 180 degrees.
Date / time	YY/MM/DD	Date and Time settings.
Power on delay	Off / 10 seconds / 20 seconds / 30 seconds	Sets the delay when turning the camera on.
Power off delay	Off / 10 seconds / 20 seconds / 30 seconds	Sets the delay when turning the camera off.
Auto Power Off	Off / 1 minute / 3 minutes / 5 minutes	By setting the time, the camera switches off automatically in the standby mode after a given period of time if it does not detect any motion.
Beep Sound	Off / On	Sets the camera’s tones On/Off.
Screensavers	Speedometer: 1 min / Speedometer: 3 min / Speedometer: 5 min / Display off: 1 min / Display off: 3 min / Display off: 5 min / Off	Instead of playing recorded footage, the camera screen can be turned off after a certain time interval, or the Speedometer function can be set.
Keyboard backlight	Auto / Off / On	Sets the backlighting of keys.
TV mode	NTSC / PAL	TV mode settings NTSC or PAL.
Frequency	50 Hz / 60 Hz	Sets frequency NTSC(60Hz) PAL(50Hz).
Language	English / French / Spanish / Portuguese / German / Italian / Hungarian / Czech / Polish / Serbian / Chinese / Russian / Japanese / Lithuanian	Language settings.
Time zone setting	N/A	Chooses the time zone.
GPS Watermark	Off / On	Sets the display of the GPS in a video.
Speed Watermark	Off / On	Shows the speed in a video.
Format	Cancel / OK	Formats data on the memory card.
Default setting	Cancel / OK	Resets the camera to the original factory settings.
Software version	TRCM_A4_V##	Displays the installed FW version.

Function	Menu item
Delete	Delete Current / Delete All
Protect	Lock Current / Unlock Current / Lock All / Unlock All
Format	Yes / No
Slide Show	2 seconds / 5 seconds / 8 seconds

LCD display	2.7 Inch 16:9
Camera	Resolution	1/3″ 3.0 mega CMOS sensor, AR0330
	View angle	130° degree
Video	Resolution	1920×1080@30fps / 1280×720@30fps / 640×480@30fps
	Standard	Mov file, H.264 compression
Micro SD card	Supports Micro SD cards up to 32 GB (Class 10 cards are recommended)
G-sensor function	Supported
File protection function	Supported
Motion detection function	Supported
Uninterrupted cycle recording	Supported
Interface	USB2.0 / HDMI
Audio	Built-in microphone
Power	12-24V car chargers
Battery	Built-in 250mAh battery
Menu language	English / French / Spanish / Portuguese / German / Italian / Hungarian / Czech / Polish / Serbian / Chinese / Russian / Japanese / Lithuanian
Operating temperature	-5°C ~ 40°C
Unit size	99x49x37 mm

The package includes: TrueCam A4 / DVR mount / Car charger / USB cable / 3M holder / Suction mount / GPS module (optional).

– For your own safety, do not use the camera’s controls while driving.

– A window mount is needed when using the recorder in a car. Make sure that you place the recorder in an appropriate place, so as not to obstruct the driver’s view or deployment of airbags.

– Make sure that no object is blocking the camera lens and no reflective material is placed near the lens. Please keep the lens clean.

– If the car’s windshield is tinted or coated, it may impact the recording quality.

– For general use it is recommended to have motion detection enabled. May lead to the memory card filling up quickly.

– The camera is primarily designed to operate while being constantly under power supply.

– Before first use, fully charge the battery.

– For charging only use chargers that are specified for this type of battery.

– Use standard cables for charging, otherwise it could damage the device.

– Never connect to a mechanically damaged charger or if the batteries are swollen. Do not use batteries in this condition due to risk of explosion.

– Do not use any damaged adapter or charger.

– Charge at room temperature, never charge at a temperature below 0°C or at a temperature higher than 40°C.

– Avoid dropping the battery, don‘t puncture, or mutilate it. Definitely do not attempt to repair a damaged battery.

– Do not expose the charger or battery to moisture, water, rain, snow or any kind of various liquids.

– Do not leave the battery in the car, do not expose to direct sunlight and do not place it near heat sources. Strong light or high temperatures can damage the battery.

– Never leave batteries without supervision during charging, short circuit or accidentally overcharge. Some batteries are unsuitable for fast charging or being charged excessively. This can cause a shock, or due to charger failure, may cause leakage of aggressive chemicals, explosion or subsequent fire!

– In the case of excessive heating of the battery during charging, immediately disconnect it from the power supply.

– Do not place charger and charging battery on or near flammable objects. Beware of curtains, carpets, tablecloths etc.

– Once the battery or device with integrated battery is fully charged, disconnect it from the power supply.

– Keep the battery out of the reach of children and animals.

– Never disassemble the charger or battery. If the battery is integrated, do not disassemble the device, unless stated otherwise. Any such attempt is dangerous and can cause injury or damage to the product and subsequent loss of warranty.

– Do not dispose worn or damaged batteries into the trash, fire or into heating devices, but hand them in at collection points for hazardous waste.

– Charge the battery under continuous supervision.

– Use only the charger supplied with your device. Use of another type of charger may result in malfunction and/or danger.

– Do not use the charger in high moisture environment. Never touch the charger when your hands or feet are wet.

– Allow adequate ventilation around the charger when using it to operate the device or to charge the battery. Do not cover the charger with paper or other objects that will reduce cooling. Do not use the charger while it is inside a carrying case.

– Connect the charger to a proper power source. The voltage requirements are found on the product case and/or on the packaging.

– Do not use the charger if it is visibly damaged. In case of damage, do not repair the equipment yourself!

– In case of device overheating, immediately disconnect the power source.

– We recommend formatting the SD card while in use once a month. This will prevent the creation of defective files and helps to protect the SD card itself against damage.

– GPS satellite signals cannot pass through solid materials (except glass). When you are inside a tunnel or a building, GPS positioning is not available. Signal reception can be affected by situations such as bad weather or dense overhead obstacles (e.g. trees, tunnels, viaducts and tall buildings).

– The GPS positioning data is for reference only.

– Taking good care of your device will ensure trouble-free operation and reduce the risk of damage.

– Keep your device away from excessive moisture and extreme temperatures and avoid exposing your device to direct sunlight or strong ultraviolet light for extended periods of time.

– Do not drop your device or subject it to severe shock.

– Do not subject your device to sudden and severe temperature changes. This could cause moisture condensation inside the unit, which could damage your device. In the event of moisture condensation, allow the device to dry out completely before use.

– The screen surface can easily be scratched. Avoid touching it with sharp objects.

– Never clean your device when it is powered on. Use a soft, lint-free cloth to wipe the screen and the exterior of your device. Do not use paper towels to clean the screen.

– Never attempt to disassemble, repair or make any modifications to your device. Disassembly, modification or any attempt at repair could cause damage to your device and even bodily injury or property damage and will void any warranty.

– Do not store or carry flammable liquids, gases or explosive materials in the same compartment as your device, its parts or accessories.

– To discourage theft, do not leave the device and accessories in plain view in an unattended vehicle.

– Overheating may damage the device.

Caution:

– The camera includes supplementary software that is eligible to detect speed cameras and other traffic safety systems. Please verify that this supplementary software is according to the law of the state where the camera is used.

– TrueCam is eligible to detect speed cameras and other systems used for securing safety in traffic by finding out their GPS coordinates, which are ascertained from the public databases. The camera is not equipped with any system that is able to detect radio waves sent out by speed cameras or other traffic safety systems.

– You can activate this function in your GPS module by setting it to the ON position. You can receive alerts to warn you about the locations of speed cameras, which will enable you to monitor your speed through these areas.