FREE ENGLISH TOSHIBA E-STUDIO6527AC (01) PDF USER GUIDE
FREE ENGLISH TOSHIBA E-STUDIO6527AC (01) PDF USER MANUAL
FREE ENGLISH TOSHIBA E-STUDIO6527AC (01) PDF OWNER GUIDE
FREE ENGLISH TOSHIBA E-STUDIO6527AC (01) PDF OWNER MANUAL
FREE ENGLISH TOSHIBA E-STUDIO6527AC (01) PDF REFERENCE GUIDE
FREE ENGLISH TOSHIBA E-STUDIO6527AC (01) PDF INSTRUCTION GUIDE
FREE ENGLISH TOSHIBA E-STUDIO6527AC (01) PDF REFERENCE MANUAL
FREE ENGLISH TOSHIBA E-STUDIO6527AC (01) PDF INSTRUCTION MANUAL
FREE ENGLISH TOSHIBA E-STUDIO6527AC (01) PDF OPERATING INSTRUCTIONS
CLICK HERE TO DOWNLOAD TOSHIBA E-STUDIO6527AC (01) PDF MANUAL
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How do I stop copying?
Press [Stop] on the touch panel.
Copying or scanning stops.
How do I stop and restart copying?
1. Press [Job Cancel] on the touch panel to stop copying.
2. Press [Next Copy] on the touch panel or the [START] button on the control panel to restart.
How do I scan the next original during copying (auto job start)?
1. Set the number of copy sets and the copy modes as required.
2. Press the [START] button on the control panel.
How do I confirm auto jobs?
You can confirm which jobs are in waiting on the touch panel or cancel them as required. For details, see the reference below:
Information About Equipment – Information About Equipment – Confirming Job Statuses of Printing/ Copying/Scanning/Faxing – Confirming jobs in progress or ones in waiting
How do I cancel jobs being scanned?
Press [Stop] on the touch panel to stop a job while originals are being scanned.
When you press [Job Cancel] on the touch panel or the [FUNCTION CLEAR] button on the control panel while the scanning is being paused, the scanning will end. (In this case, the data which were scanned before the job was paused will be copied.) To restart the scanning, press the [START] button.
How do I scan the next original during copying (priority job)?
1. Press [Interrupt Priority] and select [Priority].
2. Set the number of copy sets and the copy settings as required.
3. Press the [START] button.
How do I confirm registered priority job?
You can confirm the registered priority job on the touch panel. In addition, you can remove it. For details, see the reference below:
Information About Equipment – Information About Equipment – Confirming Job Statuses of Printing/ Copying/Scanning/Faxing – Confirming jobs in progress or ones in waiting
How do I interrupt copying and make other copies (interrupt copying)?
1. Press [Interrupt Priority] and select [Interrupt].
2. Select other copy modes as required.
3. Press the [START] button.
What are the restrictions when using interrupt copying?
The following functions cannot be used together with interrupt copying:
Cover sheet copying, Sheet insertion copying, Job build, Store to e-Filing, Copy & File
How do I make one copy as a sample (proof copy)?
1. Select the number of copy sets and copy modes.
2. Press [Proof Copy] on the touch panel.
3. Press the [START] button on the control panel.
4. Change the number of copy sets and copy modes as required after checking the proof copy.
5. Press the [START] button on the control panel.
How do I specify the orientation of originals?
1. Press a paper direction button on the Basic menu, matching the orientation of the placed original.
How do I copy with Automatic Paper Selection (APS)?
1. Press [APS] on the touch panel.
2. Select other copy modes as required, and then press the [START] button on the control panel.
How do I select the drawer for my desired paper manually?
1. Press the drawer button corresponding to the desired paper size.
2. Select other copy modes as required, and then press the [START] button on the control panel.
How do I copy mixed-size originals in one operation?
1. Press [Zoom] on the Basic menu.
2. Press [Mixed Size].
3. Select a paper size.
4. Select other copy modes as required, and then press the [START] button on the control panel.
How do I perform bypass copying on standard size paper?
1. Place paper on the bypass tray.
2. Select the same size button under “Copy” as that of the paper you placed on the bypass tray.
3. Press [Paper Type] on the touch panel if the paper type of the paper you placed on the bypass tray is other than plain paper.
4. Select the paper type, and press [OK].
5. After setting the paper size and type, press [OK].
6. Select other copy modes as required, and then press the [START] button on the control panel.
How do I perform bypass copying on other than the above standard sizes of paper?
1. Place the original(s) and paper on the bypass tray.
2. Press [Size Setting] on the touch panel.
3. Press the button of the same size as the paper you placed on the bypass tray.
4. Press [Other] under “Copy”.
5. Press [Paper Type] if the paper you placed on the bypass tray is other than plain paper.
6. Select the paper type and press [OK].
7. After setting the paper size and paper type, press [OK].
8. Select other copy modes as required, and then press the [START] button on the control panel.
How do I copy on an envelope?
1. Place the original on the original glass.
2. Place paper on the bypass tray.
3. Press [Size Setting] on the touch panel.
4. Press the button of the same size as the envelope you placed on the bypass tray.
5. Press [Other] under “Copy” and press [OK].
6. Select other copy modes as required, and then press the [START] button on the control panel.
How do I perform bypass copying on non-standard size paper?
1. Place the original.
2. Place paper on the bypass tray.
3. Press [Custom Paper] on the touch panel.
4. Key in the dimension, and press [OK].
5. Select other copy modes as required, and then press the [START] button on the control panel.
How do I change the exit tray?
To change the exit tray, press [Exit Tray]. Every time you press this, the display changes from the exit tray of the equipment, each exit tray of the finisher and Job Separator, and automatic selection in this order.
How do I switch color modes?
Press any of [Full Color], [Black] or [Auto Color] on the touch panel.
How do I adjust the density automatically?
Press [Auto] on the touch panel.
How do I adjust the density manually?
Press either or to select the desired density level.
How do I use Automatic Magnification Selection (AMS)?
1. Press [Zoom] on the Basic menu.
2. Select the desired paper size, press [AMS] and then [OK].
3. Place the original(s).
How do I specify both the original size and the copy paper size separately?
1. Press [Zoom] on the Basic menu.
2. Select the desired sizes for the original and copy paper, and then press [OK].
How do I register paper sizes to “Other” size?
1. Press [Size Setting] on the touch panel.
2. Select the desired size.
How do I register non-standard size in the memory?
1. Follow the same procedure noted in steps 1 to 3 in the reference below:
2. Register dimensions.
How do I specify the reproduction ratio manually?
1. Press [Zoom] on the Basic menu.
2. Press the buttons below to select the desired reproduction ratio.
3. Select the desired size, and then press [OK].
How do I copy photo originals in the optimal reproduction ratio for copy paper size (Photo Zoom) (Color Model only)?
1. Press [Zoom] on the Basic menu.
2. Press [Photo Zoom].
3. Select the original size.
4. Select the desired copy paper size, and then press [OK].
5. Select other copy modes as required, and then press the [START] button on the control panel.
6. Place the next original, and then press [Next Copy] on the touch panel or the [START] button on the control panel.
7. When the scanning of all the originals is finished, press [Job Finish] on the touch panel.
How do I copy photo originals of other sizes?
1. Press [Custom] on the touch panel.
2. Key in the size of the original, and press [OK].
How do I reduce images to scan the entire original, including the edges (Full Image) (Color Model only)?
1. Press [Zoom] on the Basic menu.
2. Select sizes for the original and copy paper, and press [OK].
3. Press [Full Image] on the Edit menu.
How do I make a copy with a scanned image reduced and moved to the center of the paper?
1. Press [Zoom] on the Basic menu.
2. Select a desired reproduction ratio.
3. Press [Centering Copy].
4. Press [OK] on the displayed centering copy screen.
5. Press [OK] on the [Zoom] screen.
How do I select finishing modes?
See the table below for each finishing mode.
| Finishing mode | Description |
|---|---|
| Non-sort Non-staple | Copies exit without being sorted or stapled. |
| Sort | Copies exit in the offset mode (shift exiting) in the same page order as the originals one set after another. |
| Group | Copies grouped by page exit in the offset mode (shift exiting). |
| Rotate sort | Copies exit in the offset mode (shift exiting) set by set alternately in a different direction. |
| Staple sort | Copies exit with their corner stapled. |
| Magazine sort | Copies exit in a book-type page order. |
| Center fold | Copies exit in a book-type page order with their center folded. |
| Saddle stitch | Copies exit in a book-type page order with their center folded and stapled. |
| Magazine sort & center fold | Magazine sort and center fold are used together. |
| Magazine sort & saddle stitch | Magazine sort and saddle stitch are used together. |
| Hole punch | Copies exit with their side punched. |
| Manual staple | Copies are stapled manually. |
How do I set up for Sort and group mode?
1 Press [Finishing] on the Basic menu.
2 Select [Sort] or [Group], and then press [OK].
3 Key in the desired number of copies on the Basic menu.
How do I set up for Rotate sort mode?
1 Press [Finishing] on the Basic menu.
2 Select [Rotate Sort], and then press [OK].
3 Key in the desired number of copies on the Basic menu.
How do I set up for Staple sort mode?
1 Press [Finishing] on the Basic menu.
2 Press the button for the staple position, select the direction that matches the original you set from “Original Direction”, and press [OK].
How do I set up for Magazine sort / Center fold / Saddle stitch?
1 Place the original(s).
2 Press [Finishing] on the Basic menu.
3 Select the direction that matches the direction you set from “Original Direction”, and press [Binding].
4 Select a binding mode and press [OK].
5 When you select [Magazine Sort], [Magazine Sort & Center Fold], or [Magazine Sort & Saddle Stitch], specify the binding margin and press [OK].
6 Combine the copied paper if the center fold mode or magazine sort & center fold mode is used.
How do I set up for Hole punch mode?
1 Press [Finishing] on the Basic menu.
2 Select [Hole Punch] and [Original Direction], and then press [OK].
What are the Duplex Copying options?
You can copy a 1-sided original to a 2-sided copy or vice versa, or copy a 2-sided original to a 2-sided copy. This is useful when you want to save the paper, or when you want to copy a book-type original maintaining the same page order. As for the directions of originals or copied images, “open to left” is called “book” and “open to top” is called “tablet”.
1-sided original -> 1-sided copy
2-sided original -> 1-sided copy
1-sided original -> 2-sided copy
2-sided original -> 2-sided copy
Book-type original -> 2-sided copy
How do I make a 1-sided copy?
1 Press [2-Sided] on the Basic menu.
2 Select the desired mode and original direction, and then press [OK].
How do I make a 2-sided copy?
1 Press [2-Sided] on the Basic menu.
2 Select the desired mode, book or tablet of original and paper, and original direction, and then press [OK].
How do I make a 2-sided copy from a book-type original?
1 Press [2-Sided] on the Basic menu.
2 Select [Book -> 2].
3 Select the start page to be scanned and page layout.
4 Press [OK].
5 Press the drawer button corresponding to the desired paper size.
6 Select other copy modes as required.
7 Place the original on the original glass.
8 Press the [START] button on the control panel. Once the pages are scanned, set the next ones on the original glass.
9 When all the pages have been scanned, press [Finished].
How do I clear dirty edges of originals (Edge Erase)?
1 Press [Edge Erase] on the Edit menu.
2 Adjust the width of the part to be erased, and press [OK].
How do I clearing Shadows in the Center of Book-type Originals (Book Center Erase)?
1 Select the drawer for the desired paper size.
2 Press [Book Center Erase] on the Edit menu.
3 Adjust the width of the part to be erased, and press [OK].
4 Place the original on the original glass.
How do I copy the Sides of Book-type Originals Separately (Dual Page)?
1 Press [Dual Page] on the Edit menu.
2 Press [1 Side] or [2 Side].
3 Select other copy modes as required.
4 Press the [Basic] tab to display the Basic menu, and then select A4, B5 or LT as the copy paper size.
5 Open the desired page of the original and place it on the original glass.
6 Press the [START] button on the control panel. When the scanning of the opened pages is finished, open the next pages and place them.
7 When all the pages have been scanned, press [Finished].
How do I copy Multiple Originals onto One Sheet (2 in 1 / 4 in 1)?
1 Press [2 in 1/4 in 1] on the Edit menu.
2 Perform 2 in 1 / 4 in 1 setting, and press [OK].
How do I set the printing direction when copying multiple originals onto one sheet?
Select an arrangement order of pages with the button in the menu of Direction.
Select [Original Direction] according to the placed original.
How do I copy with duplex settings when copying multiple originals onto one sheet?
To perform duplex copying, select the duplex mode.
How do I use Trimming and masking?
1 Press [Editing] on the Edit menu.
2 Select [Trim] or [Mask].
3 Place the original on the original glass with its face up.
4 Read the following 4 values to specify the area using the left and top scales on the original glass.
5 Key in the read values, and press [OK].
6 Place the original again on the original glass with its face down.
How do I use Mirror image and negative/positive reversal?
1 Press [Editing] on the Edit menu.
2 Select [Mirror] or [Neg/Pos], and then press [OK].
How do I use Applying Separate Reproduction Ratios to Vertical and Horizontal Directions (XY Zoom)?
1 Press [XY Zoom] on the Edit menu.
2 Set the reproduction ratio in both vertical and horizontal directions.
How do I perform Applying Different Settings for Cover Sheets (Cover Sheet)?
1 Place the paper for the cover sheets and specify the paper type.
2 Place the normal paper in the drawer(s).
3 Place the original(s).
4 Press [Cover Sheet] on the Edit menu.
5 Select the front and back cover
CLICK HERE TO DOWNLOAD TOSHIBA E-STUDIO6527AC (01) PDF MANUAL