FREE ENGLISH TOSHIBA E-STUDIO2525AC (01) PDF USER GUIDE
FREE ENGLISH TOSHIBA E-STUDIO2525AC (01) PDF USER MANUAL
FREE ENGLISH TOSHIBA E-STUDIO2525AC (01) PDF OWNER GUIDE
FREE ENGLISH TOSHIBA E-STUDIO2525AC (01) PDF OWNER MANUAL
FREE ENGLISH TOSHIBA E-STUDIO2525AC (01) PDF REFERENCE GUIDE
FREE ENGLISH TOSHIBA E-STUDIO2525AC (01) PDF INSTRUCTION GUIDE
FREE ENGLISH TOSHIBA E-STUDIO2525AC (01) PDF REFERENCE MANUAL
FREE ENGLISH TOSHIBA E-STUDIO2525AC (01) PDF INSTRUCTION MANUAL
FREE ENGLISH TOSHIBA E-STUDIO2525AC (01) PDF OPERATING INSTRUCTIONS
CLICK HERE TO DOWNLOAD TOSHIBA E-STUDIO2525AC (01) PDF MANUAL
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How do I stop and restart copying?
1. Press [Stop] on the touch panel.
Copying or scanning stops.
2. Press [Job Cancel] on the touch panel to stop copying.
Press [Next Copy] on the touch panel or the [START] button on the control panel to restart.
How do I scan the next original during copying (auto job start)?
Even if copying is in progress or “Ready (Warming Up)” is displayed on the touch panel, you can scan the next original (auto job start).
1. Set the number of copy sets and the copy modes as required.
2. Press the [START] button on the control panel.
How do I scan the next original during copying (priority job)?
When you scan the next original as a priority copying job, it is carried out immediately after the job in progress is finished (priority job).
1. Press [Interrupt Priority] and select [Priority].
2. Set the number of copy sets and the copy settings as required.
3. Press the [START] button.
How do I interrupt copying and make other copies (interrupt copying)?
You can interrupt the copy job in progress to make other copies (interrupt copying).
1. Press [Interrupt Priority] and select [Interrupt].
2. Select other copy modes as required.
3. Press the [START] button.
The job in progress is paused and an interrupt copying job starts.
After the interrupt copying job is finished, the interrupted one restarts.
How do I make one copy as a sample (proof copy)?
When you make a large amount of copies, you can check if they will be made exactly as you desire by copying only one set before copying them all (proof copy).
1. Select the number of copy sets and copy modes.
2. Press [Proof Copy] on the touch panel.
3. Press the [START] button on the control panel.
Scanning starts. 1 set of copies will be printed out.
4. Change the number of copy sets and copy modes as required after checking the proof copy.
5. Press the [START] button on the control panel.
How do I specify the orientation of originals?
You can specify the orientation of the placed originals.
1. Press a paper direction button on the Basic menu, matching the orientation of the placed original.
How do I use Automatic Paper Selection (APS)?
This equipment detects the size of an original and selects paper of the same size automatically.
1. Press [APS] on the touch panel.
2. Select other copy modes as required, and then press the [START] button on the control panel.
How do I select the drawer for your desired paper manually?
You need to select paper by yourself when copying the following originals whose sizes cannot be detected correctly:
1. Press the drawer button corresponding to the desired paper size.
2. Select other copy modes as required, and then press the [START] button on the control panel.
How do I copy mixed-size originals in one operation?
You can copy or scan a set of originals whose sizes are individually different, using the ADF with the mixed size function.
1. Press [Zoom] on the Basic menu.
2. Press [Mixed Size].
3. Select a paper size.
4. Select other copy modes as required, and then press the [START] button on the control panel.
How do I specify the Paper Type?
When you place any special paper other than plain paper or that not used for normal copying, you need to set the thickness and attribute into this equipment.
How do I copy onto recycled paper, thick paper?
When you place recycled paper, thick paper in the drawer, set the thickness and attribute into this equipment.
How do I copy onto thin paper, sticker labels, or special paper?
Thin paper, sticker labels, or special paper can be used to make copies by using the bypass tray.
Place such paper on the bypass tray and set the thickness and attributes into this equipment before you start copying.
How do I specify and copy cover sheets or paper to insert?
Cover sheets or paper to insert a specific page can be prepared and copied in a drawer different from an ordinary drawer.
Place paper in a drawer and set attribute as the paper type.
How do I use bypass copying?
When you make copies on OHP film, sticker labels, envelopes, or non-standard size paper, place the copy paper on the bypass tray.
Bypass copying is also recommended for copying on standard size paper which is not set in any of the drawers.
How do I copy on A3, A4, B4 and B5 size paper (in equipment other than for North America) / LD, LT, LG and ST-R size paper (in equipment for North America)?
1. Place paper on the bypass tray.
2. Select the same size button under “Copy” as that of the paper you placed on the bypass tray.
3. Press [Paper Type] on the touch panel if the paper type of the paper you placed on the bypass tray is other than plain paper.
4. Select the paper type, and press [OK].
5. After setting the paper size and type, press [OK].
6. Select other copy modes as required, and then press the [START] button on the control panel.
How do I copy on other than the above standard sizes of paper?
1. Place the original(s) and paper on the bypass tray.
2. Press [Size Setting] on the touch panel.
3. Press the button of the same size as the paper you placed on the bypass tray.
4. Press [Other] under “Copy”.
5. Press [Paper Type] if the paper you placed on the bypass tray is other than plain paper.
6. Select the paper type and press [OK].
7. After setting the paper size and paper type, press [OK].
8. Select other copy modes as required, and then press the [START] button on the control panel.
How do I copy on an envelope?
1. Place the original on the original glass.
2. Place paper on the bypass tray.
3. Press [Size Setting] on the touch panel.
4. Press the button of the same size as the envelope you placed on the bypass tray.
5. Press [Other] under “Copy” and press [OK].
6. Select other copy modes as required, and then press the [START] button on the control panel.
How do I copy on non-standard size paper?
You can specify the size of non-standard size paper and copy it.
1. Place the original.
2. Place paper on the bypass tray.
3. Press [Custom Paper] on the touch panel.
4. Key in the dimension and press [OK].
5. Select other copy modes as required, and then press the [START] button on the control panel.
How do I select the exit tray?
You can select the exit tray if the finisher or the Job Separator is installed.
The exit tray currently selected is displayed on the equipment status indication area. To change the exit tray, press [Exit Tray]. Every time you press this, the display changes from the exit tray of the equipment, each exit tray of the finisher and Job Separator, and automatic selection in this order.
How do I switch color modes (Color Model only)?
You can switch the color mode. There are 3 color modes.
Press any of [Full Color], [Black] or [Auto Color] on the touch panel.
How do I adjust density automatically (automatic density adjustment)?
This equipment detects the density level of originals and automatically adjusts the density level of the copied image to the optimal one.
Press [Auto] on the touch panel.
How do I adjust density manually?
Press either or to select the desired density level.
How do I use Automatic Magnification Selection (AMS)?
Specify the copy paper size in advance so that this equipment will detect the original size and automatically select the optimal reproduction ratio to the copy paper size.
1. Press [Zoom] on the Basic menu.
2. Select the desired paper size, press [AMS] and then [OK].
3. Place the original(s).
How do I specify both the original size and the copy paper size separately?
1. Press [Zoom] on the Basic menu.
2. Select the desired sizes for the original and copy paper, and then press [OK].
How do I register paper sizes to “Other” size?
If you want to select a size other than the following for the original size and copy paper size, you need to register the size as “Other” following the procedures below.
1. Press [Size Setting] on the touch panel.
2. Select the desired size.
How do I register non-standard size in the memory?
1. Follow the same procedure.
2. Register dimensions.
Select a desired memory number and enter the values in [Length] and [Width].
How do I specify reproduction ratio manually?
1. Press [Zoom] on the Basic menu.
2. Press the buttons below to select the desired reproduction ratio.
3. Select the desired size, and then press [OK].
How do I copy photo originals in the optimal reproduction ratio for copy paper size (Photo Zoom) (Color Model only)?
1. Press [Zoom] on the Basic menu.
2. Press [Photo Zoom].
3. Select the original size.
4. Select the desired copy paper size, and then press [OK].
5. Select other copy modes as required, and then press the [START] button on the control panel.
6. Place the next original, and then press [Next Copy] on the touch panel or the [START] button on the control panel.
7. When the scanning of all the originals is finished, press [Job Finish] on the touch panel.
How do I set photo originals in other sizes?
1. Press [Custom] on the touch panel.
2. Key in the size of the original, and press [OK].
How do I reduce images to scan the entire original, including the edges (Full Image) (Color Model only)?
1. Press [Zoom] on the Basic menu.
2. Select sizes for the original and copy paper, and press [OK].
3. Press [Full Image] on the Edit menu.
How do I reduce and center an image (Centering Copy)?
1. Press [Zoom] on the Basic menu.
2. Select a desired reproduction ratio.
3. Press [Centering Copy].
4. Press [OK] on the displayed centering copy screen.
5. Press [OK] on the [Zoom] screen.
How do I select a finishing mode?
1. Press [Finishing] on the Basic menu.
2. Select [Sort] or [Group], and then press [OK].
3. Key in the desired number of copies on the Basic menu.
How do I use rotate sort mode?
1. Press [Finishing] on the Basic menu.
2. Select [Rotate Sort], and then press [OK].
3. Key in the desired number of copies on the Basic menu.
How do I use staple sort mode?
1. Press [Finishing] on the Basic menu.
2. Press the button for the staple position, select the direction that matches the original you set from “Original Direction”, and press [OK].
How do I make a 1-sided copy?
1. Press [2-Sided] on the Basic menu.
2. Select the desired mode and original direction, and then press [OK].
How do I make a 2-sided copy?
1. Press [2-Sided] on the Basic menu.
2. Select the desired mode, book or tablet of original and paper, and original direction, and then press [OK].
How do I make a 2-sided copy from a book-type original?
1. Press [2-Sided] on the Basic menu.
2. Select [Book -> 2].
3. Select the start page to be scanned and page layout.
4. Press [OK].
5. Press the drawer button corresponding to the desired paper size.
6. Select other copy modes as required.
7. Place the original on the original glass.
8. Press the [START] button on the control panel. Once the pages are scanned, set the next ones on the original glass.
9. When all the pages have been scanned, press [Finished].
How do I display the Edit Menu?
You can display the Edit menu by pressing the [Edit] tab on the touch panel when you want to use various editing functions.
How do I create top, bottom, left, and right margins?
1. Press [Image Shift] on the Edit menu.
2. Select the type of binding margin.
3. Adjust the width of the binding margin, and press [OK].
How do I create bookbinding margins?
1. Press [Image Shift] on the Edit menu.
2. Press [Book].
3. Adjust the width of the binding margin, and press [OK].
4. Press [OK].
How do I clear dirty edges of originals (Edge Erase)?
You can whiten the edge of the copied image when a shadow-like dark part appears on it.
1. Press [Edge Erase] on the Edit menu.
2. Adjust the width of the part to be erased, and press [OK].
How do I clear shadows in the center of book-type originals (Book Center Erase)?
1. Select the drawer for the desired paper size.
2. Press [Book Center Erase] on the Edit menu.
3. Adjust the width of the part to be erased, and press [OK].
4. Place the original on the original glass.
How do I copy the sides of book-type originals separately (Dual Page)?
You can copy the 2 facing pages of a book-type original or 2 original sheets placed side by side onto 2 separate sheets of paper or on both sides of 1 sheet of paper.
1. Press [Dual Page] on the Edit menu.
2. Press [1 Side] or [2 Side].
3. Select other copy modes as required.
4. Press the [Basic] tab to display the Basic menu, and then select A4, B5 or LT as the copy paper size.
5. Open the desired page of the original and place it on the original glass.
6. Press the [START] button on the control panel. When the scanning of the opened pages is finished, open the next pages and place them.
7. When all the pages have been scanned, press [Finished].
How do I copy multiple Originals onto One Sheet (2 in 1 / 4 in 1)?
You can copy 2 or 4 originals to 1 sheet of paper by shrinking them.
1. Press [2 in 1 / 4 in 1] on the Edit menu.
2. Perform 2 in 1 / 4 in 1 setting, and press [OK].
How do I center a Scanned Image (Centering Copy)?
You can make a copy with a scanned image moved to the center of the paper.
1. Press [Centering Copy] on the Edit menu.
2. Press [OK].
How do I use Trimming and masking?
1. Press [Editing] on the Edit menu.
2. Select [Trim] or [Mask].
3. Place the original on the original glass with its face up.
4. Read the following 4 values to specify the area using the left and top scales on the original glass.
5. Key in the read values, and press [OK].
6. Place the original again on the original glass with its face down.
How do I use Mirror image and negative/positive reversal?
1. Press [Editing] on the Edit menu.
2. Select [Mirror] or [Neg/Pos], and then press [OK].
How do I use Applying Separate Reproduction Ratios to Vertical and Horizontal Directions (XY Zoom)?
1. Press [XY Zoom] on the Edit menu.
2. Set the reproduction ratio in both vertical and horizontal directions.
How do I use Applying Different Settings for Cover Sheets (Cover Sheet)?
1. Place the paper for the cover sheets and specify the paper type.
2. Place the normal paper in the drawer(s).
3. Place the original(s).
4. Press [Cover Sheet] on the Edit menu.
5. Select the front and back cover settings, and then press [OK].
6. Press the [Basic] tab to display the Basic menu. Then select a drawer in which normal paper is placed (not the one for the cover sheets).
CLICK HERE TO DOWNLOAD TOSHIBA E-STUDIO2525AC (01) PDF MANUAL