FREE ENGLISH TOASTMASTER 1503T (01) PDF USER GUIDE
FREE ENGLISH TOASTMASTER 1503T (01) PDF USER MANUAL
FREE ENGLISH TOASTMASTER 1503T (01) PDF OWNER GUIDE
FREE ENGLISH TOASTMASTER 1503T (01) PDF OWNER MANUAL
FREE ENGLISH TOASTMASTER 1503T (01) PDF REFERENCE GUIDE
FREE ENGLISH TOASTMASTER 1503T (01) PDF INSTRUCTION GUIDE
FREE ENGLISH TOASTMASTER 1503T (01) PDF REFERENCE MANUAL
FREE ENGLISH TOASTMASTER 1503T (01) PDF INSTRUCTION MANUAL
FREE ENGLISH TOASTMASTER 1503T (01) PDF OPERATING INSTRUCTIONS
CLICK HERE TO DOWNLOAD TOASTMASTER 1503T (01) PDF MANUAL
If this is not the document you want for this product, click here to see if we have any other documents for this product.
TOASTMASTER 1503T (01) PDF SUMMARY:
What are the three categories of Toastmaster electric Food Warmers?
Toastmaster electric Food Warmers are designed in three categories: drop-in, built-in, or counter units.
What type of applications are Toastmaster Food Warmers designed for?
All Toastmaster Food Warmers are designed to be used in either a wet or dry application except for models 1527H, 1527TH, 1509, and 1509D, which are for wet applications only.
What should you do when uncrating a counter type unit?
Care should be taken while uncrating a new Toastmaster Food Warmer to prevent damage and scratching of the surface. First, open the carton by removing all fastening staples. Remove and discard the internal packing material from the top of the unit. Lift the unit up and out of the carton. Locate any mounting brackets or other loose items and set aside.
How do you install the legs on counter type units?
On counter type units, except for model 1511E and 1527H, you will find four 4" plastic legs with level adjusting feet. To install these legs, turn the unit on its top or back and screw the legs into the four tapped holes in the bottom. The models 1511E and 1527H have already fixed 1 1/4" adjusting feet installed. Upright the unit on your counter.
What position should the thermostat control knob be in before connecting to electrical power?
Locate the thermostat control knob on the front panel and set it in the “OFF” position. Note that model 1528 has two controls – they must both be in the “OFF” position before connecting to the electrical power.
What voltages are available for Toastmaster Food Warmers?
Toastmaster Food Warmers are provided in different voltages: 120, 208, or 240.
What is the electrical cord length of counter units?
All counter units are shipped with a factory installed 6-foot electrical cord and plug.
Are Toastmaster Food Warmers single-phase or multi-phase?
All Food Warmers are provided in single-phase only regardless of voltage.
How should cutouts be made for drop-in models?
Cutouts for the Food Warmers should be made per the enclosed dimensions given for your model. Cutouts for the food well are to be made in the top of the counter, and the control panel is to be mounted in the front face of the counter.
How far can the control box be mounted from the unit?
The control box cannot be further away than 48", as the conduit provided is 48".
What should be done to the counter top before installing the food well?
You should provide some protection for your counter top to avoid scratching it. Do not install the food well because the opening in the counter top is required for the control box installation.
What is the first step to install the control panel?
Align the control panel front over the hole provided and align the bolt holes. Secure it with four #8 sheet metal screws provided by the installer.
How should the control box be installed?
Place the control box down through the top opening and align it with the control panel front. Reinstall the hex head bolts to secure the front to the box. Replace the recessed cup and secure with the screws removed earlier. Replace the control knob.
How is a watertight seal created when installing the food well?
Lay a bead of silastic sealer around the flange of the food well. Allow the silastic to cure for 1 hour before installing.
How are models 1504, 1506, and 1527 secured to the counter?
For 1504, 1506, and 1527, use the six flat washers and six #10-32 nuts furnished.
How are the 1509 series warmers secured to the counter?
For the 1509 series, use the four brackets and four nuts provided. The longest edge of the brackets should be positioned against the bottom edge of the counter, and the other edge next to the body of the food warmer.
How are 1503T series warmers secured to the counter?
1503T series warmers are secured to the counter with mounting brackets that completely surround the lower edge of the mounting flange. The long edge goes against the counter, and the short edge goes against the food warmer. All four pieces of the mounting brackets are secured with the fourteen nuts provided.
What should be done with excess silastic after tightening the food warmer?
Wipe up any excess silastic that oozes out around the flange when the food warmer is tightened securely.
What should the installer provide for models with drains?
If a model is equipped with a drain, the installing contractor should provide a suitable drain connection equipped with a shut-off valve.
What should you do if you plan to use a food warmer as a dry application, regarding the drain?
If you plan to use your food warmer as a dry application exclusively, the drain can be capped with a simple plumbing pipe cap.
What models are designed for wet application only?
The models 1527TH and 1509 are designed for wet application ONLY.
What is the wire connection and conduit length of drop-in models?
All Food Warmers have a 48" wire connection and conduit.
What is available in the control box for drop-in models?
All models have a knockout in the control box to allow for ease in running a 1/2" conduit from the control box to your electrical power source. The ground lug is mounted inside the control box.
Is it necessary to disconnect any pre-wired, internal wiring to complete the installation?
It is not necessary to disconnect any of the pre-wired, internal wiring of these units to complete the installation.
What should be done before using a food warmer for the first time after installation?
Before use, make the following checks: 1. Turn the control knob to the “OFF” position. 2. Turn on the main electrical disconnect. 3. Turn the control knob to the highest setting. 4. Check to see if the unit is heating (heating light should be lit).
What should you do if the unit fails to heat?
If the unit fails to heat, recheck the main disconnect and the food warmer control to see if they are on. Have the installer recheck all electrical connections.
How do you operate food warmers for wet applications, excluding models 1527H and 1527TH?
Be sure the control knob is set in the “OFF” position, then energize the unit at the main disconnect. For wet applications, fill the unit with approximately 1" of HOT water and turn the control knob dial to the high position for 25 to 30 minutes. After 30 minutes, set the control knob at the desired setting. Always keep insert pans in place or cover the unit to conserve heat and to prevent water evaporation.
How much water should be maintained in wet applications?
You should maintain at least a 1/2" water level.
Can food items be placed directly in the receptacle?
Never place food items directly in the receptacle without the use of the insert pan(s).
How do you operate food warmers for dry applications?
For dry applications, merely set the insert vessel into the food warmer.
How do you operate models 1527H & 1527TH?
Fill the warming unit with about 2 1/2 quarts of water. Place food in the Heat N’ Hold and turn the control knob to high. After approximately 18 minutes, turn the control knob to a minimum of 150° F for holding. Always keep the heating element covered with water to ensure proper heat transfer. “Dry” running of the unit will substantially lower the temperature in the insert pan. Check the water level daily.
Can food products be placed directly in the warmer well of the 1527H & 1527TH models?
Never place food products directly in the warmer well.
What are some common uses for the “Heat N’ Hold” units?
Common uses of the “Heat N’ Hold” units are soup, chili, hot chocolate, or vegetables.
What are some operating hints for Food Warmers?
When operating wet, always use hot or warm water to speed up the preheat time. Do not use too much or too little water. Keep the cover on the food insert pan and the entire food well as much as possible to avoid lost heat. Always set the controls to the off position when the unit is not preheating or in use.
What should you do before cleaning a food warmer?
Always unplug or disconnect the power to the unit before cleaning.
How should food warmers be cleaned?
Food warmers should be cleaned frequently to remove scale and prevent buildup. Vinegar and water or a commercial de-scaling agent may be used. The food warmers should be emptied daily and washed with soapy water, rinsed, and wiped dry. Extreme care should be taken while cleaning so that the electrical components do not get wet. Never submerge the unit in water.
What are the cleaning instructions for 1527H & 1527TH “Heat N’ Hold” Units?
Wipe the well daily. Wash or scour with a mild abrasive. Do not use steel wool for cleaning as it could scratch the surface and cause the unit to rust. To remove scale caused by hard water, soak with vinegar and water or a commercial de-scaling agent that is safe with copper.
What is the purpose of the adaptor kit?
The adaptor kit is used for mounting the unit into a wooden counter top.
What is the purpose of the adaptor rings?
The adaptor rings are for 7 qt and 11 qt pans for models 1527TH and 1527H.
What should you do if a Toastmaster Model 1529 food warmer is damaged in transit?
The Delivering Transportation Company is required by law to make a notation of damages on your paid freight bill. If there may be concealed damage, the Delivering Transportation Company is obliged to make an inspection after the goods are unpacked.
Who is responsible for damages during shipping?
The Carrier (not the Shipper) should be charged with any loss or damage, and any claim should be filed with the Delivery Transportation Company.
What should you do if the buzzer sounds on the Toastmaster Model 1529?
Turn the food warmer OFF. Remove the insert pan. Refill the well with the proper amount of 160 F (HOT) WATER. Reinstall the insert pan. Turn the power switch back ON.
How should the Toastmaster Model 1529 be cleaned?
Pour any remaining water out of the well. Wipe the exterior case and the well with a DAMP cloth or sponge wrung out of hot detergent water solution to remove food residue. Rinse using a clean DAMP cloth and wipe dry. Do not immerse the warmer or use excessive water when washing.
What should you do in case of fire with the food warmer Model 1529?
Unplug the warmer or turn the branch circuit disconnect OFF.
What is the purpose of the ON/OFF switch?
The ON/OFF switch turns power to the device. The signal light glows to show power is on.
What does the operating thermostat do?
The operating thermostat cycles the heating unit on and off to maintain an average temperature of 170 (filled with water to the water level mark in well).
What is the purpose of the Hi-Temperature thermostat?
The Hi-temperature thermostat turns the buzzer on when the water boils.
What does the audible buzzer do?
The audible buzzer signals the operator to fill the well with water immediately.
What are the possible causes of no signal light, no heat, and no buzzer, during normal operation?
The possible causes are: no incoming power, a defective switch, or a wire off.
What are the possible causes of no signal light, but it heats, during normal operation?
The possible cause is a defective switch light.
What are the possible causes of signal light glows, but no heat, during normal operation?
The possible causes are: a wire off, a defective heating unit, or a defective operating thermostat.
What are the possible causes of signal light glows, and the buzzer sounds during normal operation?
The possible cause is a defective Hi-temperature thermostat.
What are the possible causes of signal light glows, but no buzzer during abnormal operation (no water in well)?
The possible causes are: a defective buzzer or a defective Hi-Temperature thermostat.
What is the electrical plug configuration for Model 1511E at 120V?
The electrical plug configuration for Model 1511E at 120V is NEMA 5-15P.
What is the electrical plug configuration for Model 1511E at 208V?
The electrical plug configuration for Model 1511E at 208V is NEMA 6-15P.
What is the electrical plug configuration for Model 1511E at 240V?
The electrical plug configuration for Model 1511E at 240V is NEMA 6-15P.
What is the electrical plug configuration for Model 1523 at 120V?
The electrical plug configuration for Model 1523 at 120V is NEMA 5-15P.
What is the electrical plug configuration for Model 1523 at 208V?
The electrical plug configuration for Model 1523 at 208V is NEMA 6-15P.
What is the electrical plug configuration for Model 1523 at 240V?
The electrical plug configuration for Model 1523 at 240V is NEMA 6-15P.
What is the electrical plug configuration for Model 1521 at 120V?
The electrical plug configuration for Model 1521 at 120V is NEMA 5-15P.
What is the electrical plug configuration for Model 1521 at 208V?
The electrical plug configuration for Model 1521 at 208V is NEMA 6-15P.
What is the electrical plug configuration for Model 1521 at 240V?
The electrical plug configuration for Model 1521 at 240V is NEMA 6-15P.
What is the electrical plug configuration for Model 1527TH at 120V?
The electrical plug configuration for Model 1527TH at 120V is NEMA 5-15P.
What is the electrical plug configuration for Model 1528 at 120V?
The electrical plug configuration for Model 1528 at 120V is NEMA 5-15P.
What is the electrical plug configuration for Model 1528 at 208V?
The electrical plug configuration for Model 1528 at 208V is NEMA 6-15P.
What is the electrical plug configuration for Model 1528 at 240V?
The electrical plug configuration for Model 1528 at 240V is NEMA 6-15P.
CLICK HERE TO DOWNLOAD TOASTMASTER 1503T (01) PDF MANUAL