FREE ENGLISH TEMTOP LKC-1000S+ (LKC-1000SPLUS) (01) PDF USER GUIDE
FREE ENGLISH TEMTOP LKC-1000S+ (LKC-1000SPLUS) (01) PDF USER MANUAL
FREE ENGLISH TEMTOP LKC-1000S+ (LKC-1000SPLUS) (01) PDF OWNER GUIDE
FREE ENGLISH TEMTOP LKC-1000S+ (LKC-1000SPLUS) (01) PDF OWNER MANUAL
FREE ENGLISH TEMTOP LKC-1000S+ (LKC-1000SPLUS) (01) PDF REFERENCE GUIDE
FREE ENGLISH TEMTOP LKC-1000S+ (LKC-1000SPLUS) (01) PDF INSTRUCTION GUIDE
FREE ENGLISH TEMTOP LKC-1000S+ (LKC-1000SPLUS) (01) PDF REFERENCE MANUAL
FREE ENGLISH TEMTOP LKC-1000S+ (LKC-1000SPLUS) (01) PDF INSTRUCTION MANUAL
FREE ENGLISH TEMTOP LKC-1000S+ (LKC-1000SPLUS) (01) PDF OPERATING INSTRUCTIONS
CLICK HERE TO DOWNLOAD TEMTOP LKC-1000S+ (LKC-1000SPLUS) (01) PDF MANUAL
If this is not the document you want for this product, click here to see if we have any other documents for this product.
TEMTOP LKC-1000S+ (LKC-1000SPLUS) (01) PDF SUMMARY:
What should I do if the detector displays a higher value when turned on for the first time or unused for a long time?
Place it in a ventilated environment for 8 hours before detection.
What should I do before detection to calculate the overall air quality?
Keep the target room airtight for 10 minutes. Take the average value of multiple points in order to calculate its overall air quality.
Where should I avoid placing the detector?
Do not put the detector in the environment with formaldehyde (HCHO) concentration above 1.0 mg/m3 or PM concentration above 500 ug/m’ for a long time. Otherwise, the sensor may be damaged and cannot run normally.
What substances should the detector not contact?
Do not contact with organic solvents which include silica gel and other adhesives, paintings, drugs, oil and high-concentration gases.
In what environment should I avoid using the detector?
Do not use the detector in humid environment in order to maintain the detection accuracy.
What should I be mindful of when using the detector?
Do not cover the air inlet/ outlet when using the detector.
What might cause cross interference with the detector?
Be cautious of cross interference by ethanol, benzene, ammonia, etc.
How do I set the time on the detector?
Press the Left or Right key to set the current value, press the Up key to switch to the next item. The setting range of “year” is 2017 to 2099. After setting the time, switch to the “Save” option and press (!) to save the current setting, otherwise it will not be saved.
How do I set the storage interval?
Press the Left or Right key to set the current value, press the Up key to switch to the next item. Options: 1, 5, 10, 30 and 60 minutes.
How do I export data?
If the detector is connected to the computer and the driver is successfully installed, it enters data export mode. The computer will display a removable storage disk named “Temtop”, containing a HISTORY folder and a SYSTEM folder. The data is stored in the HISTORY folder. The SYSTEM folder contains system configuration files, which are only for engineers to repair and test the detector. After the data exported, press the “HCHO” button to exit the mode. The detector will shut down and can be used after restarted.
What should I do if the USB connection is unsuccessful?
If the detector has connected to the computer but the driver fails to be installed, it will pop up a tip and shut down. Please restart the detector and try again.
What does it mean if the detector displays “No use connection detected?”
If the USB cable is not used to connect to the computer for data export, the detector will not find the correct connection and pop up a tip. Please connect it in the right way.
What should I check if the detector fails to connect to the computer?
If the detector fails to connect to the computer, check the computer or data cable whether it supports data export function.
How do I switch the detector On/Off?
Hold the power button 2 seconds to turn on/off the detector.
What should I know about the detector’s automatic shut off?
The detector will automatically off after 1 hour of inactivity. This Auto off function is disabled in graph view interface.
How does the detector work?
After switch on the detector, it will automatically start to detect the concentration of pollutants in the air, such as PM2.5, PM10, HCHO, etc.
What is Running mode?
In Running mode, the detector always displays currently detected data.
What is Hold mode?
In Hold mode, the detector paused the detection function and will stop updating data on the screen.
How do I store and export data?
Adjust the time and save the data detection interval in “Setting”. After the detector is correctly connected to the computer, obtain and check the data history on the computer.
How do I charge the battery?
Plug in the supplied USB cable to the charging port of the detector.
What do the battery icons indicate?
IIlilll: Battery full. D: Battery low. Please charge.
CLICK HERE TO DOWNLOAD TEMTOP LKC-1000S+ (LKC-1000SPLUS) (01) PDF MANUAL