TAYLOR SWODEN 330200LYG (01) PDF MANUAL

Read the manual carefully before using the appliance for the first time and retain these instructions for future reference.

Before operating the appliance for the first time, make sure the dust cup is installed correctly.

This appliance should only be used with a power supply of 220-240V~50-60Hz.

Do not vacuum water, hazardous material, burning material, or ashes.

Please change the dust cup/HEPA immediately in the event it gets damaged.

Do not store or use the machine in or near to high-temperature locations.

If the appliance breaks or makes an abnormal noise, produces a strange smell, or emits smoke during operation, turn it off and unplug it from the switch immediately. Contact your service center for repair. Do not attempt to repair it yourself.

Any damaged power supply cords should only be replaced by the manufacturer, its service agent, or a similarly qualified person.

This appliance should only be operated by children aged eight years and above and those who have a reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they are adequately supervised, have been instructed on its safe use, and understand the hazards involved. Children should never be permitted to play with the appliance. Cleaning and user maintenance shall not be performed by children without supervision.

The vacuum cleaner consists of the following parts:

1. Brush tool

2. Extending metal tube

3. Dust chamber

4. Hose connector

5. Dust cup handle

6. ON/OFF and speed control knob

7. Back wheel rubber

8. Back wheel

9. Handle

10. Hose

11. Winding device button

12. Dust cup release button

13. Round brush

14. Crevice nozzle

15. Furniture brush

16. 3-in-1 accessories holder

Insert the hose into the hose connector in front of the dust chamber. To remove the hose, press the hose release button and pull it out.

Hold the flexural connector of the hose and put it into the bigger hole of the tube until fixed in place. If you want to disassemble it, press the hose release button and pull it out.

Slide button: The suction power and inner vacuum degree can be controlled by opening or closing the slide. For instance, if you find the resistance is too high when using the floor brush, open the slide. This decreases the power of the vacuum and subsequently makes it easier to move the vacuum head over the floor.

The length of the tube can be adjusted by pulling the adjustment switch.

Push the extending tube into the brush hole until firmly in place.

When cleaning hard floors, lower the bristles by pushing gently on the tread pedal with one foot. When cleaning carpeted floors, push on the tread pedal again to raise the bristles.

When cleaning hard floors, open the suction control slide to reduce resistance. When cleaning carpeted floors, close the slide to generate stronger suction.

When operating the appliance, do not continue to pull the power cable out of the vacuum beyond the yellow mark. If the power cable has been removed to the extent that the red mark can be seen, retract some of the cable. When you have completed the cleaning process, turn off the power, remove the appliance plug from the socket, and push the power cable retract button until the cord has been fully retracted back into the machine.

Insert the plug into the socket, press the power button to turn on the machine, and rotate the speed control button to control the power of the suction.

Round brush: Used primarily for cleaning desktops and other smooth surface furniture.

Crevice nozzle: Mainly used to clean between narrow gaps. The narrow aperture will significantly enhance the vacuum and suction.

Furniture brush: Used for cleaning soft furnishings, such as sofas, curtains, upholstery, etc.

3-in-1 accessories holder: The 3-in-1 accessories holder can be hung on the metal tube to store the additional accessories.

Step 1. Hold the dust chamber and handle and press the release button. Remove the dust chamber from the machine.

Step 2. Uncover the dust chamber and remove the dirt and dust.

The filter should be cleaned twice a year, or when there is visible dirt on the filter.

Fix the filter securely in place before operating the vacuum cleaner.

The filter should not be vacuumed or cleaned in a washing machine.

Make sure the filter is thoroughly dry before use. The use of a wet filter will reduce the suction power and could damage the motor.

1) Press the outlet grid lock to open the outlet cover. Remove the HEPA filter.

2) Remove the dust cup locker, open the dust cup cover, and remove any dust and debris. Take out the filter rack and MIF sponge.

3) Clean all the dust on the filter rack. All filters can be washed by hand. Wash the dust cup, dust cup cover, and outlet grid, and allow them to dry before reassembling the appliance fully.

4) Reassemble all accessories and make sure they are fixed firmly in place.

When not in use, neatly store the appliance in a cool, dry location away from direct sunlight. The floor brush can be stored at the back of the appliance to save space.