Post questions, comments, reviews or page errors in the comment box below.

Click here to download TASER AXON BODY (02) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** (D TASER Axon Body Quick Start Guide English (U.S./Canada/Australia/U.K.) Hardware Axon Body Camera Quick Reference Operation LED o Top View Recharging/Dataport Data Transfer & Recharging through PC or Evidence.com Dock Camera Lens Speaker Battery LED Green Yellow = – Red = Less Than 20% Microphone AXON Volume/Pairing Bottom View Bluetooth Pairing and Upload Status LED Power Switch Red On/Buffering Event Button Double Tap = Start Record Hold 3 Sec = Stop Record Battery Status Button Push to Show Status of Battery Axon Body USB Cable Axon Body Wall Charger Step 1: Recording The Axon Body camera has two operating modes. The default mode, or BUFFERING mode, provides pre-event buffering to capture activities that occur before you activate the EVENT (recording) mode. 1 Turn the system on. Move the ON/OFF switch to the ON position. Audio quality will be reduced if the camera is not in the holster. 2 To record, quickly double-press the EVENT button. The camera now records audio as well as video. The camera will beep twice to let you know that recording has sta rted. The 2 beeps will repeat every 2 minutes (if the system is muted, there will be no audio notifications). The operation LED will blink red. Event Button Solid Red Boot Up Mode ..r— Blinking Green / Buffering Mode Blinking Red – Record Mode The camera takes a few seconds to boot up and be ready to record (the red area under the switch will be exposed with the switch moved to the ON position). The operation LED will be solid red and then transition to blinking green when the system goes into BUFFERING mode. The Axon Body camera will go into BUFFERING mode after the boot up sequence. The BUFFERING mode holds the previous 30 seconds of video [NO AUDIO leading up to the beginning of a recording. Step 2: Camera Operation LED The Axon Body camera’s operation LED displays the system’s current operating 3 To stop recording and return to BUFFERING mode, press and hold the EVENT button for at least 3 seconds until there is a long, audible beep. Because the system does not capture audio in BUFFERING mode, the first 30 seconds of a recorded event will be video-only (depending on your agency’s settings). BUFFERING mode starts only after the camera is turned on. The system does not record when the Axon Body camera is turned off. Step 3: Battery LED The camera’s battery LED displays the battery’s remaining capacity, when the device mode. Operating Mode Recording Buffering Booting up/powering down Operation LED Blinking red Blinking green Solid red is being used or when charging. Battery Status Battery capacity is 41 —100% Battery capacity is 20-40% Battery capacity is less than 20% Battery critically low I Battery LED Green Yellow Red during operation; flashing red and yellow during charging Blinking red and yellow

****** Page 2 ****** Step 4: Audio Notification The camera emits beeping sounds called audio prompts to notify you of the system status. These audio prompts usually occur after you perform an action with the Step 5: Recharging the Battery and Uploading Data Ifyou do not have an Evidence.com Dock, upload video with a Windows compatible computer using Evidence Sync: TASER.com/syncdownload. camera. Operating Mode Powering on or off Recording an event Press the battery button while the camera is recording The device is ending an event and returning to BUFFERING mode The battery is at 20% capacity or lower Camera memory is full (camera will not record). Step 6: Audio Notification One beep Two beeps (every two minutes) Two beeps One long beep Four quick beeps (every 20 seconds) Three beeps 2 Ensure the Axon Body camera is off. Insert the camera into the Evidence.com Dock as shown. The Evidence.com Dock automatically uploads data to Evidence.com, deletes videos from the camera, and charges the camera. (The camera must be registered to your Evidence.com account.) At the beginning of the next shift, ensure that your camera (if one has been assigned to you) displays with a green upload status LED before removing it from the Evidence.com Dock. Axon Body Evidence.com Dock Upload Status LED When you plug your camera into the Evidence.com Dock, the upload status LED on the bottom of the camera displays the system’s status System Status Initial connection (momentary) In queue awaiting upload Uploading data Device ready (all videos uploaded successfully) Device not assigned, agency mismatch, camera set in the offline mode, or device error Evidence.com Dock has no communication with the camera Firmware update, internal battery charging, extremely low battery, or memory full Network error Transfer error, device re-trying to transfer Step 7: Using Axon Mobile The Axon Mobile application enables you to replay video and add metadata (GPS, title, case ID, and category) to your videos using a smart phone or multimedia player. I LED Indication Solid red (for 20 seconds or fewer) Solid yellow Blinking yellow — DO NOT remove the camera from the Evidence.com Dock Solid green Blinking red LED off Blinking red and yellow — DO NOT remove the camera from the Evidence.com Dock Blinking red, yellow, and then green Blinking green and yellow Step 8: Pairing the Axon Body Camera with a Smart Device 1 2 3 Using your smart device, download the Axon Mobile application from the Google Play store or the iTunes App Store. Search Axon Mobile. On your smart device, open the Axon Mobile application and follow the onscreen instructions for Bluetooth pairing. See diagram below (or see Step 8: Pairing an Axon Body camera with a Smart Device). To add categories to your videos you will need to sign into your agency. In the Axon Mobile app go to the Settings menu, select Agency, enter your email address and select your agency. You will now be able to add categories to your Axon Body videos. (Must be connected to Internet.) oo O 2 3 4 5 1. While holding down the volume/pairing button, move the ON/OFF switch to the ON position. Wait until you hear 3 beeps. The pairing LED will blink green. Release the volume/pairing button. Using your smart device’s Bluetooth settings, pair it with the Axon Body camera. You will hear 3 beeps when the devices are paired. The Axon Body camera will AXON then go into BUFFERING mode. Hold down PairingNolume Button 3. Pairing LED will blink green, you will hear 3 beeps Turn on Axon Body camera 2. Note: All data is stored on the Axon Body camera. No videos are stored on your smart device. For more information, see the Axon Body Camera User Manual, Evidence@com Dock Quick Start Guide, Axon Mobile forAndroid Devices User Manual, or Axon Mobile for IOS Devices User Manual, available at TASER.com, au.TASER.com, uk.TASER.com. Additional information is available at axon.io/. Bluetooth is a trademark of the Bluetooth SIG, Inc. Google Play is a trademark of Google, Inc. iTunes is a trademark of Apple, Inc. IOS is a trademark of Cisco Systems, Inc. Windows is a trademark of Microsoft Corporation. AXON are trademarks of TASER International, Inc. TASER, Axon, and (D are trademarks of TASER International, Inc., registered in the US and other countries. For Evidence.com and more information, see TASER.com/IegaI. All rights reserved. 0 2015 TASER International, Inc. MPC0168 Rev: D


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL

TAGS:

TASER AXON BODY (02) PDF MANUAL

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.